KTC M27T20 Mini LED Monitor User Guide

KTC M27T20 Mini LED Monitor

Important Safety Precautions

1. Please read all the instructions carefully before using the product.

2. When cleaning the display, please unplug the power card. Please wipe the display with a soft wet cloth instead of liquid or spray cleaner. Please use LCD screen cleaner in case aft a stubborn stain.

3. Do not use accessories that are not recommended by the manufacturer, or there may be dangerous.

4. When unplugging the power cord of the display or the power adapter, please hold the power plug with your hand rather than directly pull the power cord to unplug it.

5. Do not place the display near water, such as bathtub, washbasin, kitchen sink, or washing machine. Do not place the display on the wet ground, or near the swimming pool. Do not use fingers or hard objects to press the surface of the LCD screen.

6. The grooves and hales on the sheller at the back and bottom of the display are designed for the ventilation and heat dissipation of the components to ensure reliable operation. So, do not put the display on the bed, sofa, carpet, or other similar surfaces to prevent the heat dissipation hales farm blocking and do not place the display nearer above the radiator or heater. In addition, do not place the display in an embedded device unless adequate ventilation is provided.

7. Daly the power supply type shown on the nameplate can be used for the display. Please feel free to consult the display dealer or the local power supply administration, if you have any doubts about your power supply type.
   For safety, the display or the power adapter uses a power cord with a three- prong plug, whose third prong can only be properly grounded when used with a properly grounded Socket. If your socket cannot match with the plug, please contact an electrician to replace your original socket so that the plug can give full play to ensuring safety.

8. As you may face high voltage are other dangers after removing the shell, do Nat repair the display by yourself. You can have it repaired by qualified maintenance personnel.

9. Please unplug the power cord of the display or the power adapter from the socket, and contact qualified maintenance personnel for repairing the display, when following cases occur:
   a. The power cord or the plug is damaged or worn out.
   b. The display has been dropped from high or the shell is damaged.
   c. Any obvious abnormality indicates a necessary repair.

10. Please place the display in a well-ventilated environment, which is away from strong light, high temperature, or humidity.

11. The roam temperature for the display stare is-10 °c ~ 60 °C, ar it may be permanently damaged.

Product Introduction

Overview

It is a Kind of high-performance intelligent multiple frequency scanning display, which adopts active matrix thin film transistor LED-backlit LCD and is controlled through the microcomputer MCLI digital technology. It is compact and lightweight, which is suitable for narrow working spaces.

Packing List

Before installation, check whether the following articles are complete in the packing box:

• Display x1
• Stand x1
• Base x1
• Power Card x1
• Power Adapter x1
• DP Signal Cable x1
• User Guide x1
• HDMI Cable x1
• Warranty Card x1

If any of above product is missing, please contact with product distributor immediately,
NOTICE: Specific accessories in order to prevail in kind. Please keep packing materials for future movement.

Installation and Connection

Display Installation

Installation Guide

• The display should be installed near an AC power socket that can be easily pluggable.
• For safety purpose, it is recommended to use suitable wall mount brackets or a base.
• To prevent injury, the display should be placed on a smooth horizontal plane, or fixed on a firm wall.
• If you need to install it on a wall, it should be done by professional technicians. The improper display installation may cause instability.
• Do not place the display where it may be suffered from mechanical vibration.
• Do not place the display where insects may enter.
• Do not place the display directly facing an air conditioner, or the internal panel may condense, leading to faults.
• Do not place the display where there is a strong electromagnetic field, or it will be interfered with and damaged by the electromagnetic waves.
  

Signal Cable Connection

Connect the signal coble to the HDMI or DP signal output port on the PC, then connect the other end of the signal coble to the corresponding signal input port on the LCD.

Headset Connection

After connecting to the headset, there will be audio output, and it also supports external loudspeakers.

USB Connection

Use the USB 3.D Type-B coble to connect the USB uplink port on display with the USB port on the case, or use the Type-c cable to connect the Type-C port on display with the USB port on the case. Switch o port corresponding to KVM through the joystick to enable the USB port on display to transmit do to.

Display Operation

The joystick is shown so in the figure. For the models of the some series, only the key positions and the frame styles are different. Please refer to the actual situation for details.

Power Indicator

The blue indicator represents the proper functioning of the display; the red flash indicator represents no signal state. Under the energy conservation state, the display will normally work if the signal is provided again. The display is still powered on in the standby state. Thus, unplug the power cord when you do not use the display for safety.

Key Function Introduction

Initial Status:

pressing and holding for 3 seconds.

Enter the Function Menu:

Safety Protection

When the PC video signal exceeds the frequency range of the display, the display will disable the line and field synchronizing signals to protect the display. Under this circumstance, you must set the output frequency of the PC ta an acceptable range for the display to work properly.

Simple Problems Disposal

supply is in goad contact with the display and the power socket; and check whether the display is turned off.
2. Dark screen| Enter the “Brightness & Contrast” menu to regulate the contrast and the brightness of the display.
3. Display overheating| Leave at least 5cm of ventilated space around the display. Do not place articles on the display.
4. Dark/light spats when powered an| It is normal. Because of the temperature difference in the environment, the backlit tube emits uneven light at the initial stage after the display turns on. However, the backlit tube will emit normal light after 20 minutes, and the dark/light spots will be eliminated at that time.
5. image distortion, flashing, shaking| Check your computer configuration, choose the correct resolution, and reset your refresh rate.
6. Noise y signal when powered off| During the power-off of the display, there may be some noisy signals on the screen caused by the normal discharge .

Product Technical Specifications

Requirements of Operating Environment
Barometric Pressure
Working Temperature and Humidity
Storage Temperature and Humidity| B6kpa- 104 kpa
0C ~40 C  20% ~ 85%
-10 C ~6D C  10% ~ 90%
Packing Dimension (WxHxDJ and Weight
Display Dimension (WxHxDJ [excluding base] Packing Dimension (WxHxDJ
Net Weight of Display (including base] Packing Weight| 617.Bx364.2×64.Bmm
875x225x500mm
6.9Kg
11.BKg

Power Management System

<24DW  (including Type-CJ
Standby| <0.5W

Remark: All technical specifications in the User Guide and on the external packing are allowed to change without prior notice. If there is a subtle difference between the User Guide and the actual operation, the latter shall prevail.

Instruction for base installation

Indicative Description of The Regulations for the Administration of the Recovery and Disposal of Waste Electrical and Electronic Products

To care for and protect the earth better, please send it to a local manufacturer with nationally recognized qualification for recycling according to the national applicable laws and regulations on recycling of waste electrical and electronic products when you no longer need this product or at the end of its service life.

The environment-friendly use period of this product is 10 years (see the Marking for the Restriction of the Use of Hazardous Substances in the right figure).
such use period will be maintained, only if you use the product under the normal working conditions specified in the User Guide only.

Warranty Rules

1. We provide you with a one-year free warranty from the doted of purchase or as agreed in the contract.
2. The following cases are not covered by the warranty:
   • Failure or damages caused by artificial or natural disasters.
   • Failure caused by not following the operation method and precautions written in the User Guide.
   • Failure caused by user disassembly.
3. The liability scape of the warranty card is limited to the maintenance of the product, without covering any other liability,
4. lf you are not sure about the repair and warranty of the machine after the warranty period, please visit the website www.ktcplay.com for the warranty policy.
   

Customer Support

More Information
Please scan QR code or visit www.ktcplay.com

Any question or comments. Please contact:
support@ktcplay.com [North America] support.eu@ktcplay.com [Europe]

 The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI Lago are trademarks or
registered trademarks of HDMI Licensing Administrator, lnc. in the United States and other countries.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>