KTC H34S18S Series 34 Inch Ultrawide Monitor User Guide
- June 1, 2024
- KTC
Table of Contents
KTC H34S18S Series 34 Inch Ultrawide Monitor User Guide
Product Introduction
It is a kind of high-performance intelligent multiple frequency scanning display, which adopts active matrix thin film transistor LED-backlit LCD. The display is controlled through the microcomputer MCU digital technology. It is compact and lightweight, which is suitable for narrow working spaces.
Before installation, please check whether the following articles are complete in the packing box:
- LCD×1
- Basex1
- Power Cordx1
- Power Adapter<1
- Warranty Card×1
- Signal Cablex2
- Screwdriver×1
- User Guidex1
If any of above product is missing, please contact with product distributor immediately.
Notice: Specific accessories in order to prevail in kind. Please keep pocking materials for future movement,
Keys And Interfaces
| Initial Shortcut Keys| Enter the Function Menu
---|---|---
| Signal Source Input| Move Up
| Luminance| Move Down
| Shortcut Key for Gaming Assistance| Exit and Return Previous Menu
| Shortcut Key for Preset| Open Sub-menu and Select an Option
| Turn on the display by short-pressing.Turn off the display by pressing and
holding for 3 seconds| Turn off the display by pressing and holding for 3
seconds
Signal Cable Connection
Connect the signal cable to the HDMI or DP signal output port on the PC,
then connect the other end of the signal cable to the corresponding signal
input port on the LCD.
Headset Connection
After connecting the headset, there will be audio output, and it also supports
external loudspeakers.
Upgrade through USB
The USB port is only used to update display firmware from a USB mobile device.
Do not insert any other devices.
Power Indicator
The blue indicator represents the proper functioning of the display, the red
flash indicator represents no signal state. Under the energy conservation
state, the display will normally work if the signal is provided again. The
display is still powered on in the standby state. Thus, unplug the power cord
when you do not use the display for safety.
Base And Wall Mount
-
Installing the Base:
a. Install the base onto the stand and fasten it with three M4×16 screws;
b. Tilt the base in the direction of the second arrow and install it into the back shell hole.Then press and lock the whole base in the direction of the third arrow.
-
If you want to remove the whole base, do the following:
a. Push upward the slider near the VESA cop on bose;
b. Lift and take out the base along the arrow direction.
-
Rotating lifting bracket
a. be rotated left and right
b. lift up and down R
c. Pitch back and forth
Use M4 screws 100×100mm
Recommended screw length is 8mm If you need wall mounting bracket, you need to
buy it separately)
Mounting Location
Install on the wall
Install on the base
- Please leave the space around the display with the size at least shown in the figure.
- Do not cover the ventilation hales or insert anything into the shell.
- Unless there are proper ventilation conditions and adequate ventilation space around the display, do not place the display within a limited space, such as a book cabinet or a built-in closet.
Installation Guide
- The display should be installed near on AC power socket that can be easily pluggable.
- It is recommended to use suitable wall mount brockets or a base for safety purpose.
- To prevent injury, the display should be placed on a smooth horizontal plane, or fixed on a firm wall.
- If you need to install it on a wall, it should be done by professional technicians, The Improper display installation may cause instability.
- Do not place the display where it may be suffered from mechanical vibration.
- Do not place the display where insects may enter.
- Do not place the display directly facing an air conditioner, or the internal panel may condense, leading to faults.
- Do not place the display where there is a strong electromagnetic field, or it will be interfered with and damaged by the electromagnetic waves.
Safety Protection
When the PC video signal exceeds the frequency range of the display, the display will disable the line and field synchronizing signals to protect the display. Under this circumstance, you must set the output frequency of the PC to an acceptable range for the display to work properly.
Power Management System
Remark: All technical specifications in the User Guide and on the external packing are allowed to change without prior notice. If there is a subtle difference between the User Guide and the actual operation, the latter shall prevail.
| Mode | Power Consumption |
|---|---|
| Normal Operation | $65W |
| Standby | $0.5W |
Product Technical Specifications
| Panel Dimension | 34″ |
|---|---|
| Best Operating Resolution Ratio | 3440×1440@165hz |
| Input Voltage | DC 19V/3.42A |
| Contrast | 4000:1(TYP) |
| Visible Area | 797.22(H)×333.72(V) |
| Pitch size for wall mount | 100mm×100mm |
Working Environment Requirements Maximum altitudeAtmospheric
pressureOperating temperature and humidity Storage temperature and humidity|
5000m86kpa~106kpa0C~40C 30%~90%(Non-condensing)-20C~55 C 20%~93% (Non-
condensing)
---|---
Packing Dimension and WeightDisplay Dimension (excluding base)Packing
Dimension Net Weight of Display (including base)Packing Weight|
811.8×115.2×366.6mm995×225×475mm7.4Kg11Kg
Simple Problems Disposal
| Symptoms | Disposal Methods |
|---|---|
| 1.Blank screen/Power indicator does not work | Check whether the power supply |
is in good contact with the display and the power socket; and check whether
the display is turned off.
2.Blurred too large or too small images| Go to the “Image Settings” category
menu and select “Image Auto Adjust to make the monitor adjust automatically to
correct. (Only available for monitors with VGA)
3.Dark screen| Enter the “Brightness & Contrast” menu to regulate the contrast
and the brightness of the display.
4.Display overheating| Leave at least 10cm of ventilated space around the
display. Do not place articles on the display.
5.Dark/light spots when powered on| It is normal. Because of the temperature
difference in the environment, the backlit tube emits uneven light at the
initial stage after the display turns on. However, the backlit tube will emit
normal light after 20 minutes, and the dark/light spots will be eliminated at
that time.
6.Image distortion, flashing, shaking| Check your computer configuration,
choose the correct resolution, and reset your refresh rate.
7.Noisy signal when powered off| During the power-off of the display, there
may be some noisy signals on the screen caused by the normal discharge.
Important Safety Precautions
-
Please read all the instructions carefully before using the product.
-
When cleaning the display, please unplug the power cord. Please wipe the display with a soft wet cloth instead of liquid or spray cleaner. Please use LCD screen cleaner in case of a stubborn stain.
-
Do not use accessories that are not recommended by the manufacturer, or there may be dangerous.
-
When unplugging the power cord of the display or the power adapter, please hold the power plug with your hand rather than directly pull the power cord to unplug it.
-
Do not place the display near water, such as bathtub, washbasin, kitchen sink, or washing machine. Do not place the display on the wet ground, or near the swimming pool. Do not use fingers or hard objects to press the surface of the LCD screen.
-
The grooves and holes on the shell or at the back and bottom of the display are designed for the ventilation and heat dissipation of the components to ensure reliable operation. So, do not put the display on the bed, sofa, carpet, or other similar surfaces to prevent the heat dissipation holes from blocking and do not place the display near or above the radiator or heater. In addition, do not place the display in an embedded device unless adequate ventilation is provided.
-
Only the power supply type shown on the nameplate can be used for the display. Please feel free to consult the display dealer or the local power supply administration, if you have any doubts about your power supply type. BFor safety, the display or the power adapter uses a power cord with a three-prong plug, whose third prong can only be properly grounded when used with a properly grounded socket. If your socket cannot match with the plug, please contact an electrician to replace your original socket so that the plug can give full play to ensuring safety.
-
As you may face high voltage or other dangers after removing the shell, do not repair the display by yourself. You can have it repaired by qualified maintenance personnel.
-
As you may face high voltage or other dangers after removing the shell, do not repair the display by yourself. You can have it repaired by qualified maintenance personnel. 10. Please unplug the power cord of the display or the power adapter from the socket, and contact qualified maintenance personnel for repairing the display, when following cases occur:
a. The power cord or the plug is damaged or worn out.
b. The display has been dropped from high or the shell is damaged.
c. Any obvious abnormality indicates a necessary repair. -
Please place the display in a well-ventilated environment, which is away from strong light, high temperature, or humidity.
-
The room temperature for the display store is -20°C~55°C, or it may be permanently damaged.
-
The monitor screen is fragile, so please be careful when moving or handling it!
Indicative Description of The Regulations for the Administration of the Recovery and Disposal of Waste Electrical and Electronic Products.
To care for and protect the earth better, please send it to a local manufacturer with nationally recognized qualification for recycling according to the national applicable laws and regulations on recycling of waste electrical and electronic products when you no longer need this product or at the end of its service life.
Please scan QR code or visit www.ktcplay.com
Any question or comments. Please contact:
support@ktcplay.com [North America]
support.eu@ktcplay.com [Europe]
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>