Tenda PH6 AV1000 Gigabit Passthrough Powerline Adapter Kit Installation Guide
- June 4, 2024
- Tenda
Table of Contents
Tenda PH6 AV1000 Gigabit Passthrough Powerline Adapter Kit
- Applicable to P6 and its kit: This Installation Guide is for installation instruction only. For more product or function details, please visit http://www.tendacn.com.
Attention
wiring
Plug and Play
- Connect one adapter to one of the LAN ports of a router for internet access, and plug it into a wall receptacle nearby.
- Connect the other adapter to a wired device such as a set-top box of a TV, and plug it into a wall receptacle
Optional
Secure Your Powerline Network
- 1. Plug in your adapters.
- 2. Hold down the Pair/Reset button on one adapter for 1 second, and the PLC LED indicator on the adapter starts blinking.
- 3. Hold down the Pair/Reset button on the other adapter for 1 second within 2 minutes after the previous step Observe the PLC LEDs on the two adapters until they light up and keep on.
LED & Button
FAQ
Q1: I cannot access the internet after finishing the installation. What should
I do?
A1: Try the following methods:
- Verify that your router and the adapters are connected properly.
- Verify that you can access the internet normally by connecting your computer directly to the router or modem.
- Verify that your computer has been set to obtain an IP address automatically.
- Verify that the PLC LEDs on the adapters are solid green. If they are not, reset all adapters and then observe the PLC LEDs again.
- Verify that all powerline adapters are in the same electrical circuit.
Q2: I cannot access the internet after finishing the operations in Secure
Your Powerline Network, what should I do?
A2: Try the following methods:
-
Verify that you can access the internet before using the Pair/Reset button to secure your powerline network.
-
Verify that the PLC LEDs on the adapters are solid green. If they are not, reset all adapters and then use the Pair/Reset button to pair
the adapters again. -
Verify that all powerline adapters are on the same electrical circuit.
Q3: An adapter failed to connect to the powerline network after I moved
it to a new location, what should I do?
A3: Try the following methods:
- Verify that all powerline adapters are on the same electrical circuit.
- Verify that the PLC LED on the adapter is solid green before you move it to a new location.
- Use the Pair/Reset button to pair it with another adapter in the powerline network again.
Q4: The PLC LED does not light up. What should I do?
A4: Try the following methods:
- Verify that all powerline adapters are on the same electrical circuit.
- Refer to Secure Your Powerline Network to pair the powerline adapters.
- Reset all powerline adapters to factory settings by holding down the Pair/Reset button for 6 seconds.
Q5: Can a single powerline adapter establish a Powerline network?
A5: No, it cannot. A minimum of two powerline adapters are required.
Q6: Can this Powerline device communicate with other adapters of different
manufacturers or types?
A6: Yes. This Tenda powerline adapter kit complies with
HomePlugAV/Homeplug AV2 standard and can communicate with other manufacturers’
HomePlugAV//Homeplug AV-compliant Powerline devices.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures.
For PLUGGABLE EQUIPMENT, the socket outlet shall be installed near the
equipment and shall be easily accessible.
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. (2) To
avoid unnecessary radiation interference, it is recommended to use a shielded
RJ45 cable.
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution! Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. (2) To
avoid unnecessary radiation interference, it is recommended to use a shielded
RJ45 cable.
RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment. User has the choice to
give their product to a competent recycling organization or to the retailer
when he buys new electrical or electronic equipment.
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, NO.1001, Zhongshanyuan Road, Nanshan District,
Shenzhen, China. 518052
United States Hotline:
1-800-570-5892
Canada Hotline: 1-888-998-8966
HongKong Hotline: 00852-81931998
Skype: Tendasz
Website: http://www.tendacn.com
E-mail: support@tenda.com.cn
Copyright
© 2017 Shenzhen Tenda Technology Co., Ltd. All rights reserved. Tenda is a
registered trademark legally held by Shenzhen Tenda Technology Co., Ltd. Other
brand and product names mentioned herein are trademarks or registered
trademarks of their respective holders. Specifications are subject to change
without notice.
Operating Temperature: 0 °C~40 °C
Operating Humidity: (10~90) % RH, non-condensing
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>