Foxelectronics FOX GRB1605 Bathroom Heater Instruction Manual
- June 14, 2024
- Foxelectronics
Table of Contents
FOX GRB1605 Bathroom Heater
INSTRUCTIONS FOR CONVECTOR
Bathroom heater
FOX GRB1605
Models covered by this instruction sheet:
220V-240V~
50-60Hz
IP23
2000 W
Bathroom heater.
IMPORTANT
Read these instructions fully before using the heater. Retain these
instructions for future reference.
NOTE : The frost protector with thermostat is for keeping small. It is
for use within the home or for similar purposes. The heater may only be used
in a fixed position and only for the purpose described.
It is not for outdoor use!
SAFETY INSTRUCTIONS (to be read before operating the heater)
- This product is a wall mounting appliance, never use it as portable appliance.
- Do not use the heater unless the feet are correctly attached if the heater is used as portable appliance.
- This heater in designed for wall mounting and must be used with the warm air vent facing downwards. This heater should not be used in any other orientation and should not be used as a free standing portable appliance.
- This heater must be installed so that switches and other controls (except the pull cord) cannot be touched by person in the bath or shower
- This product is suitable for installation on surfaces with normal flammability e.g. wood, plasterboard, masonry. It is not suitable for use on highly flammable surface (e.g. polystyrene, textiles)
- The heater is to be installed so that switches and other controls cannot be touched by a person in the bath or shower.
- Before making fixing hole(s), check that there are no obstruction hidden beneath the mounting surface such as pipes or cables.
- The chosen location of your new heater should allow for the product to be securely mounted(e.g. to a firm wall) and safely connected to mains supply
- Ensure the power supply to the socket into which the heater is plugged is in accordance with the rating label on the heater and that the socket is earthed.
- Keep the mains lead away from the hot body of the heater.
- Do not use outdoors.
- Do not cover or obstruct any of the heat outlet grilles or the air intake openings of the heater.
- Do not place the heater on carpets having a very deep pile.
- Always ensure that the heater is placed on a firm level surface. Ensure that the heater is not positioned close to curtains or furniture as this could create a fire hazard.
- Do not position the heater in front of, or immediately below, a wall socket.
- Do not insert any object through the heat outlet or air intake grilles of the heater.
- Do not use the heater in areas where flammable liquids are stored or where flammable fumes may be present.
- Particular care should be taken when the heater is situated in areas occupied by children or invalids.
- Always unplug the heater when moving it from one location to another.
- Do not use the heater if the power cord is damaged. If the power cord is damaged it must be replaced by a recognised service agent or other qualified person.
- Only use a suitable 220-240V electrical socket.
- The room which is to be heated should not contain any easy inflammable materials (e.g., petrol, solvents, spray cannisters etc.) or other easy combustible materials (e.g., wood or paper). Keep such materials away from equipment. Risk of fire!!
- This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
OPERATION INSTRUCTIONS
-
Before inserting the plug into an electrical outlet, make sure that the electrical supply in your area matches that on the rating label on the unit.
-
Carefully remove the heater from the plastic bag and the carton.
-
Place the heater on the wall, set the master button to “-”position. plug the cord set into a AC220-240V~ electrical outlet,with “BEE” sounds the “ ”light is on and the heater will shows the default temperature ,it will twinkle 3 seconds.
-
HEATING PERPARE
** Set time
** Before turn on the heater, set the time as right time. Press remote control “ ” button, light on control panel, it shows current Room temperature. WEEK Press “Set” button one time, “ ”lights on, press “ “two buttons set the week from 1–7 (1=Monday,2=Tuesday…7=Sunday etc.)
HOUR Press “Set” button again,“ ” lights on, “ two buttons set the Hours from 01–00(01=1 o’clock,02=2 o’clock…00=24 o’clock etc.)
MINUTE Press “Set” button again,“ ” lights on, “ two buttons set the Minutes from 00–59(01=1 Minute,02=2 Minute etc.)
PS: Press “Set” button, screen shows number will twinkle 5 seconds, you should operate in time ,otherwise appliance will get back to standby. (Appliance will keep the right time until power off) -
GENERAL USING OPERATION
1.Turn the heater ON by pressing the “ ” main button with the light is on. The unit will blow the cold air and “ ” light is on.
2.Pressing the “ ” button ,the unit will blow the warm air and both“ ”and“ ” lights are on.
3.Pressing the “ ” button second times,the unit will blow the hot air and both “ ”“ ” lights are on.
4.Pressing the “ ” button Three times,the unit will blow the cold air and “ ” light is on.
5.Pressing the “ ” button,the unit will set timer from “01-24” and “ ” light is on.”00” means closed timer.
PS: Control panel “ ” button is same function with remote control “ ” button. -
24H Timer FUNCTION
1. Open the appliance as working conditions,(fan, warm, hot are all ok). Control panel “ ” button and remote control “ ” button are same operate way.
2. Press “ ” button ,set the timer up to 24 hours, keep press “ ” button to increase the hours from 00–24(00= close,01=1hour,02=2 hours…24=24 hours etc.) and the “ ” light is on.
PS: set as “00” means no set timer ,the “ ” light is off -
THERMOSTAT INSTRUCTIONS
1. Open the appliance as working conditions,(fan, warm, hot are all ok).This function only through by Remote control.
2. To adjust temperature, press the “ ” to set the desired temperature and the temperature set from 10 to 49 .
3. When the air temperature drops 2 degree below the set temperature, the heater will start heating with ” ”(1000W).
4. When the air temperature drops 4 degree below the set temperature ,the heater will start heating with” ”(2000W).
5. When the air temperature high 1 degree or ≤the set temperature, the heater will blow the cold air . -
Weekly Timer FUNCTION
1. Open the appliance as working conditions,(fan, warm, hot are all ok).This function only through by Remote control.
2.WEEK Press “ ”button 1st time,“ ” and”W-Timer” are lights on, show “1” means “Monday”.
HOUR Press “ ” button 2nd times,“ ” lights on, “ two buttons set the Hours from 01–00(01=1 o’clock,02=2 o’clock…00=24 o’clock etc.)
MINUTE Press “ ” button 3rd times ,“ ” lights on, “ two buttons set the Minutes from 00–59(01=1 Minute,02=2 Minute etc.)
———————————————————This is open time
HOUR Press “ ” button 4th times,“ ” lights on, “ two buttons set the Hours from 01–00(01=1 o’clock,02=2 o’clock…00=24 o’clock etc.)
MINUTE Press “ ” button 5th times ,“ ” lights on, “ two buttons set the Minutes from 00–59(01=1 Minute,02=2 Minute etc.)
———————————————————This is close time The above are finished set Monday Timer.
3.Press “ ” button once more,“ ” lights on, show “2”means “Tuesday”.Please note that to operate with open time HOUR/MINUTE and close time HOUR/MINUTE are all same as before Monday.
4.From 1-7(1=Monday,2=Tuesday…7=Sunday etc.) are all set finished, press “ ” button on remote control 7th times to set from Monday to Sunday’s temperature and press“ two buttons, select the temperature which you need, the temperature range from 10 to 49 .
PS: In Week timer function, when you set today’s temperature, the thermostat function will start, the rules same as 4) THERMOSTAT INSTRUCTIONS, please noted.
You can set different open time, closed time and temperature within whole week. -
Window Open Function
1. Open the appliance as working conditions,(fan, warm, hot are all ok).This function only through by Remote control.
2.Press “ ” button, the “ ” light is on. The appliance is working as smart saving energy models.(In this function, the appliance is check and record environment temperature in immediately. It will stop working, when the appliance check the environment are drop 3 .The user should restart the appliance with “ON/OFF” button)
3..Press “ ” button again, the “ ” light is off. Window Open Function is closed. -
Delay Function
This function can be use should be fit two points: the appliance is in the standby state, before the appliance working.
This function only through by Remote control.
2.Press “ ” button light on LED display ,then press “ ” button one time, the “ ” light and “ ” light are on. press “ two buttons set the Hours from 01–24(01=1 o’ clock,24=24 o’clock…00=Closed ect.)
———————————————————This is open time
3.Press “ ” button again, the “ ” light and “ ” light are on. Press “ two buttons set the Hours from 01–24(01=1 o’clock,24=24 o’clock…00=Closed etc.)
———————————————————This is close time
PS: Press “ ” button, screen shows number will twinkle 5 seconds, you should operate in time ,otherwise appliance will get back to standby.
(This function is one-time and must be reset after the power is cut off.) -
Child-Lock Function
This function only through by Remote control. When appliance are plug in, this function can be used in any models.
Press “ ” button one time, all lights and LED display are closed ,only “ ” light on. In this condition, both control panel and remote control are fault use.
Press “ ” button again, all lights are on and both control panel and remote control are use to succeed.
CONTROL PANEL VIEW:
REMOTE CONTROL VIEW:
- Remote control, please use Lithium battery CR2025 3V.
- The remote control power button is label as such 1.”ON/OFF” Power button
2.“24H” Setting timer from 1-24 hours
3.“MODE” COLD,WARM,HOT 3 setting for selection
4.“LOCK” Child-Lock function
5.“AUTO” Window Open function
6.“Delay” Wake up and set temperature of one week
7.“W.Timer” Weekly timer
8.“+” Increase
9.“-” Decrease
10. “Set” Set real time
MOUNTING AND ELECTRICAL CONNECTION
- when mounted, enough space must be left around heater
- get three holes in the wall above the floor(seeing setting sketch A,B,C position),be sure to make the diameter just as same as the expanding pipe, insert plastic expanded pin into all three holes
- fix two screws in the expanding pipe (as sketch A&B position),keep the tips of the screws out for 10mm ,and hang up the machine after the screws are strong enough
- fix the bottom screw on the expanding pipe (as sketch C position)
MOUNTING AREA
Note:
This product is suitable for mounting in Zone 3 or the safe zone of a bathroom
( or similar ) only if a permanent connection to the mains supply is made in
accordance with the requirements of the building Regulations ( including the
wiring Regulations).
If in doubt, consult a qualified electrician.
OPERATION OF THE HEATER
NOTE : It is normal when the heaters are turned on for the first time or when they are turned on after having not been used for a long period of time the heaters may emit some smell and fumes. This will disappear when the heater has been on a short while.
CLEANING THE HEATER
- Always un-plug the heater from the wall socket and allow it to cool down before cleaning.
- Clean the outside of the heater by wiping with a damp cloth and buff with a dry cloth. Do not use any detergents or abrasives and do not allow any water to enter the heater.
STORING THE HEATER
When the heater is not used for long periods of time it should be protected
from dust and stored in a clean dry place.
INDORMATION ON THE DISPOSAL AND RECYCLING OF THIS PRODUCT
Please note that your product is marked with this symbol:
This means that the product should not be mixed with normal household waste,
as there are separate collection facilities for Waste Electrical and
Electronic Equipment.
The WEEE Directive legislation requires each Member State to provide for the
correct collection, recover, handing and recycling of Waste Electrical and
Electrical Equipment.
Private households within the EU can return their used equipment to designated
collection sites free of charge. In certain member states, if you purchased
the equipment through retail or a distributor, you can return your used
equipment to them free of charge providing you purchase similar new equipment.
Please contact your retailer, distributor or local authority for further
details on the handling of Waste Electrical and Electrical Equipment.
Owing to our constant development of our products on both functionality and
design we reserve the right to change the product without preceding notice.