MOVON OSmart Witness Adas Camera User Guide
- June 6, 2024
- MOVON
Table of Contents
MOVON OSmart Witness Adas Camera User Guide
1. About Product
2. Product Functions
1. Automatic Booting
Once the AP1 has been wired to your OBD-II port or vehicle power source the AP1 willbe boot up automatically. It will take around 55sec. for the unit to be ready to operate.
2) ADAS Functions
3)Video Recording
Continuous Record
This is the default mode for recording. In this setting the unit will begin
recording afterboot up and record the entire time the unit is powered on. The
resolution and framerates can be set as per your requirements.
Event Record
The unit will record when triggered by impact, FCW warning situation or a push
of the“Record” button. You can set the record time during the calibration
setting mode.
Dual Record
The continuous record file will be stored on “Normal Folder” and the Event
record will be stored on the “Event” folder on SD card.
Drive Data
The DRV file will be recorded during the driving even if there are no events
or video. The DRV file consist of GPS and G-sensor data. The DRV file
overwrites the oldest data. The DRV files will be made every 1~10 minutes.
Time and date
This information will be provided by GPS satellite’s automatically.
SD Memory card format
Please format(erase) the SD card using the server program.
4) Hotspot
Please press the multi-function button for 3 seconds (Long Press).
5) Volume control
Please press the volume button. The volume level is 5 steps and it make loop.
3. LED and Audio Guide
flashing (On and off): 500msec on and 500msec off
Fast flashing (On and off): 100msec on and 100msec off
*Slow flashing (On and off): 1,000msec on and 1,000msec off
4. Technical Support & Warranty
1) Technical Support
For technical Support, please contact your local distributor or visit
support.smartwitness.com
2) Limited Warranty
This product is supplied with 2 years warranty. The Warranty excludes products
that have been misused (including accidental damage) and damage caused by
normal wear and tear. In the unlikely event that you encounter a problem with
this product, it should be returned to the place of purchase.
FCC Regulations:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) This device must accept any interference received,
including interference that may cause undesired operation.
This device has been tested and found to comply with the limits for a Class B digital device , pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiated radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Caution: Changes or modifications not expressly approved by the party responsible for compliance could void the user‘s authority to operate the equipment.
RF Exposure Information
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
FCC radio frequency exposure limits, human proximity to the antenna shall not
be less than 20cm (8 inches) during normal operation.
ISED Notice
This device complies with Innovation, Science and Economic Development Canada
license-exempt RSS standard(s). Operation is subject to the following two
conditions:
(1) this device may not cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
This Class B digital apparatus complies with Canadian ICES-003.
ISED Radiation Exposure Statement
This device complies with RSS-102 radiation exposure limits set forth for an
uncontrolled environment. In order to avoid the possibility of exceeding the
ISED radio frequency exposure limits, human proximity to the antenna shall not
be less than 20cm (8 inches) during normal operation.
Read More About This Manual & Download PDF:
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>