BESTTEN DS06M Super Slim Digital Led Dimmer Switch User Manual
- June 14, 2024
- Bestten
Table of Contents
BESTTEN DS06M Super Slim Digital Led Dimmer Switch
Warnings and Cautions
- Risk of fire and electrical shock. The dimmer must be installed in accordance with appropriate electrical codes and regulations.
- Turn the power off at the circuit breaker or fuse and test that power is off before installing.
- After installation, it is recommended to set the minimum brightness level so all bulbs turn on immediately.
- If you are unsure about any part of these instructions, consult a licensed electrician.
- To reduce the risk of overheating and possible damage to other equipment, do not install to control a receptacle, a motor-operated appliance, or a transformer-supplied appliance.
- Use with compatible dimmable LED, CFL bulbs, Incandescent, or halogen bulbs only.
- When multiple bulbs are used with one dimmer DO NOT mix bulb types. All bulbs must be either LED, CFL, or incandescent. Using the exact same model for each bulb will enhance dimmer performance.
Functional Specifications
-
Status Indicator
- Indicator lights red: OFF status
- Indicator lights white: ON status
- Quickly Press: Within 0.5s
- Press and Hold: Over 0.5s
Continuous Quickly Press: Each interval of Continuous Quickly Press should within 1s
-
Maximum Brightness Button Setting the maximum brightness There are six maximum brightness levels, Quickly pressing the maximum brightness button once can change the maximum brightness level.
-
Minimum Brightness Button Setting the minimum brightness: There are six minimum brightness levels, Quickly pressing the minimum brightness button once can change the minimum brightness level.
-
Power Button
- Quickly press once to turn ON/OFF.
- Quickly press the power button six times to set the ideal minimum brightness.
- Quickly press the power button eight times to set the ideal maximum brightness.
- Continuous quick press ten times and the status indicator will flash three times to restore the factory default settings when at maximum brightness.
-
Dimming Button (UP)
- Quickly pressing the dimming button once will increase the brightness level.
- Press and Hold the dimming button will continuously increase the brightness until released or maximum brightness is achieved.
- Quickly press two times to instantly turn lights on to maximum brightness.
-
Dimming Button (Down)
- Quickly pressing the dimming button once can decrease a level of brightness.
- Press and Hold the dimming button will continuously decrease the brightness until released or minimum brightness is achieved.
- Quickly press two times to instantly turn lights on to minimum brightness.
-
Power Cut-off Button
- Pull out the power cut-off button to cut off power to the switch and light. Push back in to reconnect power.
Installation Tools
- No.2 Philips Screwdriver: Multi Meter
- Electrical Tape: Pliers
- Wire Cutters: Ruler
Installation
- WARNING: To avoid fire and electrical shock, TURN OFF THE POWER at the circuit breaker or fuse and test that power is off before wiring.
- Remove the screws installed on the existing wall plate and switch, and carefully pull out the switch from the wall box.
- 3 Identify and mark each wire attached to the switch.
- Do not remove the wires from the switch until they have been identified and marked. (This step is not required for new installations.)
- Identify the type of wiring in the wall box, 3-way, or single pole.
Note: If the wires in the wall box are different from the following layouts, please consult an electrician.
Single Pole
- Line (Hot)
- Neutral
- Ground
- Load
3-Way
- Line or Load (See note below)
- Neutral
- Ground
- Traveler 1
- Traveler 2
Important
Please note that for 3-way applications, on the existing switches, there
are 3 terminals. One of the terminals on each switch will be a different color
than the other 2. This terminal will be connected to the line or load and can
be marked Line/Load.
Typical wiring application
-
4a Single-Pole Connection style 1
-
Connect the green wire on the dimmer to the ground wire in the wall box, and secure the connection with a wire nut.
-
Connect the black wire on the dimmer to the wire labeled line, and secure the connection with a wire nut.
-
Connect the red wire on the dimmer to the wire labeled load, and secure the connection with a wire nut.
-
The remaining brown wire on the dimmer is not used it this application and must be capped with a wire nut.
IMPORTANT
In 3-way applications, this dimmer is wired very differently than a
standard 3-way switch or dimmer. The wiring for the non-dimmer 3-way switch
will also need to be altered for the dimmer to work. Please follow the wiring
diagrams very carefully. This dimmer will not work in a circuit where a 4-way
switch is used. It is very important that you identify all wires in both the
wall box that the dimmer will be installed and the other 3-way switch before
installation.
WE HIGHLY RECOMMEND EMPLOYING THE SERVICES OF A TICKETED ELECTRICIAN
You will need to identify;
Traveler 1: There are 2 traveler wires that must be identified
individually and they go between the wall box with the line and the wall box
with the load.
You must identify each traveler wire independently and ensure that it is the
same wire in each box. Mark one as Traveler 1 in each wall box.
Tip; To identify each traveler separately you can confirm the wire is the
same in each wall box by temporarily connecting the end of one traveler wire
to the ground wire in one wall box and checking with a meter for continuity
between the ground and the traveler in the other wall box. Mark this wire in
both boxes.
You can double-check this by disconnecting the ground wire and checking that
there is no longer continuity between the ground and the marked wire.
- Traveler 2: Of the 2 traveler wires that go between the wall box with the line and the wall box with the load, you must identify the second traveler wire and mark it Traveler 2 in each wall box.
- The LINE: This is the wire that has power coming in from the electrical panel. This wire will have power at all times regardless of switch positions.
- The LOAD : This is the wire that goes from one switch to the lights. It will be in a different wall box than the LINE wire.
4b-1 3-Way (3-Way Switch)
Connection style 2
Location
- Connect the green wire on the dimmer to the ground wire in the wall box, and secure the connection with a wire nut.
- Connect the black power wire on the dimmer to the wire labeled line or load, and secure the connection with a wire nut.
- Connect the brown wire on the dimmer to the Traveler 2 wire, and secure the connection with a wire nut.
- Connect the red wire on the dimmer to the Traveler 1 wire, and secure the connection with a wire nut.
Location 2
- Connect the Jumper wire together with the wires labeled Traveler 1, and the wire tagged Line or Load. Twist all 3 wires together and secure the connection with a wire nut. Connect the other end of the Jumper wire to the Common Terminal on the 3-way switch.
- Connect the wire labeled Traveler 2 to the terminal screw 1 or 2 on the 3-way switch.
4b-2 3-Way (Single Pole Switch)
Connection style 3
Location 1
- Connect the green wire on the dimmer to the ground wire in the wall box, and secure the connection with a wire nut.
- Connect the black power wire on the dimmer to the wire labeled line or load, and secure the connection with a wire nut.
- Connect the brown wire on the dimmer to the Traveler 2 wire on the 3-way switch, and secure the connection with a wire nut.
- Connect the red wire on the dimmer to the Traveler 1 wire on the 3-way switch, and secure the connection with a wire nut.
Location 2
- Connect the Jumper wire together with the wires labeled Traveler 1, and the wire tagged Line or Load. Twist all 3 wires together and secure the connection with a wire nut. Connect the other end of the Jumper wire to terminal Screw 1 on the Single Pole Switch.
- Connect the Traveler 2 wire to terminal Screw 2 on the Single Pole Switch.
Installing dimmer
- Carefully position all wires inside the junction box, leaving enough space to insert the dimmer.
User Instructions
Troubleshooting
SPECIFICATION
SCAN
Documents / Resources
|
BESTTEN DS06M Super Slim Digital Led Dimmer
Switch
[pdf] User Manual
DS06M Super Slim Digital LED Dimmer Switch, DS06M, Super Slim Digital LED
Dimmer Switch, Slim Digital LED Dimmer Switch, Digital LED Dimmer Switch, LED
Dimmer Switch, Dimmer Switch, Switch
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>