CLEAN WATER STORE J-PRO-22 Pump Proportional Feed Soda Ash Installation Guide

June 12, 2024
CLEAN WATER STORE

J-PRO-22 Pump
Proportional
Feed Soda Ash
Installation & Start-Up GuideCLEAN WATER STORE J-PRO-22 Pump
Proportional Feed Soda AshClean Water Made Easy
www.cleanwaterstore.com

Thank you for purchasing a Clean Water System!
Please review this start-up guide entirely before beginning to install your system and follow the steps outlined for best results.
Specifications:
Pumps 0.1 to 22 gallons of solution per day
Injects into line pressures up to 110 PSI
Dual voltage. 110V or 220V, works on either voltage.
Uses maximum 22 watts of power.
Dimensions:
15-gallon model: 14.5” wide x 24”, height including pump is 35”.
35-gallon model: 18” wide x 33”, height including pump is 44”.
NOTE ABOUT 220V INSTALLATIONS: This pump is dual voltage right out of the box and works on 110v OR 220v.
If you plan to install to run on 220v-240v, we recommend cutting off plug and either hard-wiring to 220v circuit OR installing a 220v plug-end.
This pump is intended for indoor use, or for outdoors if protected from sunlight and freezing.CLEAN WATER STORE J-PRO-22 Pump Proportional Feed Soda
Ash - Figure 1

Questions?
Call us toll-free: 1-888-600-5426 or 1-831-462-8500
Email us: support@cleanwaterstore.com
See more information on our website: www.cleanwaterstore.com/resources

We recommend Pro Products pure NSF grade additive-free soda ash.
Click Here for more info.

J-Pro-22 Metering Pump Warranty and Returns

Your pump comes with a 1 Year Warranty from date of delivery.
If your pump fails under warranty, please call or email our office to obtain a Returns Good Authorization Number before sending us back the pump for repair or replacement under the warranty. No returns can be accepted without an  RGA number.
The Warranty covers repair and/or replacement of the metering pump but not shipping costs.
While defects are rare, we do our best to respond to warranty returns fast as we can. Please allow 3 to 5 business days after pump has been returned for your pump to be repaired or a new one supplied under the warranty agreement.
If the water supply and its continuous chlorination are critical, a back-up pump should be on hand. Shipping charges are not covered under warranty. A flat fee of $9.95 each way will be charged for ground shipping (continental US). Any  expedited shipping (overnight, 2-day, etc.) is the customer’s responsibility.

Conditions Not Covered by the Warranty

Power surges or outages that cause pump failure are not covered under warranty.
Surge protection is strongly recommended. If a pump is returned for warranty replacement and the cause of failure is determined to be from a voltage spike, the pump does not qualify for replacement. This is the leading cause of failure.  Pump failure during, or because of, power failure is not covered under warranty.
This pump is intended for indoor use only. The pump must never be exposed to freezing temperatures, direct sunlight, or rain. If the cause of failure is determined to be from exposure to any of these environments, the pump does not qualify for replacement and will not be covered under warranty.

Pre-Installation

  1. Review your packing list and make sure you have received all the parts before beginning installation.
  2. If you turn off the water to the house and you have an electric water heater, shut off the power to the water heater before beginning installation in case water heater is accidentally drained.
  3. Pick a suitable location for your chlorination system on a dry level spot where it won’t be exposed to freezing temperatures or direct sunlight. Maximum line pressure is 100 PSI.
  4. Get all plumbing parts together before beginning installation.

Installation Over-View Steps

  1. Install the Flow Sensor
    horizontally with the display facing up in a location where it is easy to connect with the J-PRO-22 pump and electrical outlet.

  2. Install the soda ash injection check valve (included with your order) after the flow sensor into a tee in the pipe.

  3. Install flow sensor and injection valve after existing pressure tank (if you have a pressure tank).

  4. Connect the flow sensor cable to the J-PRO-22 pump cable, follow steps below in this guide to set the pump to automatic.

  5. Plug the JPRO-22 into a wall outlet and follow steps later in this guide to program and set pump.

  6. Now, when there is water flowing through the Flow Sensor, the JPRO-22 pump will inject soda ash based on the flow of water.

CLEAN WATER STORE J-PRO-22 Pump Proportional Feed Soda Ash - Figure
3

How Your Soda ash Injection System Works

Install the Flow Sensor horizontally with the display facing up in a location where it is easy to connect with the J-PRO-22and electrical outlet. Attach meter cable to pump per instructions below. Whenever water flows through flow sensor,  a precise amount of soda ash solution will be injected, and acid water pH will be neutralized to a neutral or alkaline pH (greater than 7 pH, typically 7 – 8 pH).
Example Installation with Optional Contact TankCLEAN WATER STORE J-PRO-22
Pump Proportional Feed Soda Ash - Figure 4

Example Installation with Optional Static Mixer & Spin-Down Pre-FilterCLEAN
WATER STORE J-PRO-22 Pump Proportional Feed Soda Ash - Figure
5

J-PRO-22 Installation Instructions
While you can mount the pump on a shelf above the solution tank, it is strongly advised to mount the pump directly on top of the solution tank. If the tubing from the foot valve to the suction side of the pump exceeds 60”, the unit will not  have enough lift force to stay primed.

Mount Pump to Solution tank
Place pump on tank. Mark where the anchor holes will be drilled. Drill pilot holes with a small drill bit so that the pump can be mounted on the tank with two wood or sheet metal screws. We recommend screwing them in after the pump has been primed and the tubing has been hooked up for easiest installation. 02
Mark the holes for the suction tube and the degassing return line and drill holes.

How to Connect Tubing & Fittings

Note: Warming tube ends with hot water or a hair dryer helps with tubing installation.

  • Trim the end of the tubing square (cut with a new box cutter blade).
  • Slide the connector nut onto the tube.
  • Push the tubing over the conical fitting until the tubing is flush against the end of the fitting.
  • Screw the connector nut on, hand tight.
  • Do not use Teflon tape/ paste on the tubing fitting connections.

CLEAN WATER STORE J-PRO-22 Pump Proportional Feed Soda Ash - Figure
7

Use the harder/stiffer translucent tubing for connection from discharge-side (12 o’clock) to the injection check valve.
Use the softer clear tubing for the foot valve to suction-side (6 o’clock) connection.

Install Discharge Side Tubing

This is the hard tubing that goes from the pump discharge (outlet) to injection check valve in pipe tee.

  1. Shut off well pump or water supply and de-pressurize service pipe.
  2. Install injection check valve by installing a pipe tee in your pipe that has a ½” NPT fitting, where you can screw in the injection check valve (included with your J-PRO-22 pump).
  3. Wrap Teflon tape on the ½” pipe threads of the injection check valve and apply a light coating of white Teflon pipe paste and install into Tee fitting.
  4. Trim the end of the injection check valve fitting so that the end will be in the center of the service pipe.
  5. Make sure to install injection check valve in to pipe directly. If the end of the check valve is not in the service pipe, it will not work. Do not install a ball valve, or any length of pipe run, coming off the tee.
  6. Using a hack saw or cutter, trim the end of the injection check valve if needed, so it inserts into the water pipe as shown.
  7. Install tubing that came with your pump and connect pump to injection check valve.
  8. Cut tubing to desired length with enough slack to avoid kinks.

CLEAN WATER STORE J-PRO-22 Pump Proportional Feed Soda Ash - Figure
8

Injection check valve can be installed into PVC, copper or other piping.

Install Suction Tubing from Pump to Solution Tank

Connect soft tubing from foot valve in Solution Tank to Inlet/ Suction side of metering pump

  1. Measure the tubing from the outside of the solution tank to ensure it will be 2-3” from the bottom of the solution tank.
  2. Do not allow weight to sit at the bottom of the tank. Connect tubing to the foot valve and put the ceramic weight on.
  3. Run the tubing up through the hole and connect to the Inlet/ Suction side of pump

CLEAN WATER STORE J-PRO-22 Pump Proportional Feed Soda Ash - Figure
9

Connect Tubing from Degassing Port (“Kicker Port”)
You can use the soft tubing for this run, connect tubing to the degassing port fitting (labeled on the pump as “Kicker Port”) and pass tubing through the hole you drilled down into the tank 4-6”.

CLEAN WATER STORE J-PRO-22 Pump Proportional Feed Soda Ash - Figure
10

Connect the Cables (wiring) for the J-PRO-22 Pump

  1. Flow Meter Cable WHITE wire Connects to Pump Cable RED wire (trim back, disregard other color wires)
  2. Flow Meter Cable BLUE wire connects to Pump Cable GRAY wire. (trim back, disregard other color wires)
  3. Solder or connect the wires with wire nuts, or electrical tape and then seal with shrink wrap or electrical tape.

Prime & Start the Pump with Water First

  1. Add 3 gallons of distilled or purified or softened water to solution tank.
  2. Turn the 2FV “kicker port” (which is the Degassing Valve) counter-clockwise to open approximately ½ to 1 turns.
  3. Plug the pump in to electrical outlet.
  4. Pump will be in Manual Mode, with the % at 100%
  5. “Motor” light will be Green. “Auto” light will be off.
  6. Press the ON-OFF button, pump will start pumping.
  7. After the pump is primed, close the degassing valve. This valve will remained closed for normal operation.
  8. After the pump has been in operation for a few hours, re-tighten the four stainless steel bolts on the head. Take care not to overtighten as you may damage the pump.

Program and Set the Pump

NOTE: When making programming changes to the pump, you must wait at least 15 seconds for the updated changes to be stored in the memory. Making additional changes or shutting off power to the pump prior to this waiting period  will default back to the original settings.
When first plugged in, pump display will read “100” and be in Manual (non- pulse) mode. “MOTOR” light will be green.

  1. Press and hold the SET button for several seconds until “AUTO” light turns green.
  2. Now press and hold both the SET button and UP Arrow button for a moment and release.
  3. Using UP Arrow button only, adjust to 2, which gives you two pump strokes for each gallon of water flowing through the flow meter. If you get into negative numbers, you must scroll the down arrow key to zero in order to scroll up  to positive numbers.
  4. After you have selected the number of strokes per gallon, press and release the Set button to confirm the setting.
  5. Finally press the ON-OFF button once, and now your pump is in automatic mode.
    Note: Check to see if pump is operating correctly by running the water and comparing pump actuations vs. programmed strokes per gallon of water flowing through the meter.
    During Auto mode, numbers appearing on the readout have no meaning or direct correlation to amount of solution being injected.
    Later you can adjust it higher (or lower) depending on the desired chlorine residual. For more information on that, see example calculations below.

How to Select the Solution Strength and Strokes Per Gallon Setting
The goal of a properly functioning soda ash injection system is to have a pH of between 7.0 and 8.0 in the piping system.
This is accomplished by adjusting the soda ash soda ash solution strength and setting the J-PRO-22 number of strokes per gallon (each time the pump registers a gallon and sends a pulse to the pump).

How Much Soda Ash Should Be Injected?
Generally, you want to inject 100 to 200 mg of soda ash solution for each liter of water (mg/L) to raise the pH from the acidic 5 – 6 pH range up to the 7 to 8 pH range.
Milligrams per liter is the same as saying parts per million (PPM).
Mix Up the Soda Ash Solution
Soda ash is a powder (sodium carbonate) that is mixed with water to form a saturated solution.
You can make the solution stronger or weaker.
To start out, mix 4 lbs. (or measure 8 cups) of soda ash powder in 2 gallons of very warm or hot (not boiling though) softened, distilled or purified water and stir vigorously to mix.
Add that to the 3 gallons you already have in your solution tank.
After start-up of system and to replenish soda ash solution mix 8 cups of soda ash powder per 5 gallons of warm water and stir vigorously.
Use warm or hot water (but not boiling water) to mix up solution. This will do a better job at dissolving the soda ash powder into the water.
Use purified water or softened water to make up the solution.
It is best to use purified distilled or reverse osmosis or bottled water, or clean softened water to make up your solution. If your untreated well water is soft water and is very low in total dissolved solids and other minerals, it might be OK to use the untreated water to make up the solution.
NOTE: Some soda ash will drop out of solution and settle to bottom of solution tank. This is normal.

Example Formula & Calculations
Soda ash Calculations (Using an example or assumed maximum flow rate of 10 gallons per minute, which is a typical maximum flow rate for many homes. You can change the calculations by using your number, this is an example only.)
Max flow rate: 10 Gallons Per Minute (“GPM”)
Applied soda ash dose: 100 PPM
Solution strength: 100,000 PPM
Formula Steps: (formula below uses cubic centimeters, or CC’s of which there are 3785 CC’s in one gallon)

10 GPM x 3785 x 100 38 cc/minute

100,000 ppm

The J-PRO-22 metering pump has an output of 58 cc/min and can stroke a maximum of 100 strokes a minute.
Figure Percent of pump output required related to maximum output of pump:

Choose Strokes Per Gallon Setting
Since pump can pump 100 strokes per minute, and we want approximately 60% of that, we need 60 strokes per minute, at the maximum flow rate of 10 gallons per minute.
Choose 6 Strokes/gallon:
10 GPM x 6 Strokes Per Gallon Setting = 60 strokes/minute

Where to Buy Soda Ash?

We recommend Pro Products pure NSF grade additive-free soda ash.
Click Here for more info.
Or Visit www.CleanWaterStore.com

Can I use pool soda ash?
Yes, you can, if its certified for drinking water and has no additives. Often pool supply stores sell the soda ash in 50 lb. bags at a good price.
Our soda ash is in a resealable 5-gallon bucket and is NSF certified for drinking water.
NOTE: there is also a type of soda ash available that is for certified for drinking water, but has phosphate additives in it, which helps keep the injection check valve cleaner. However, this is not suitable if you have water treatment systems  such as iron filters or reverse osmosis system as the phosphate additive can foul the water treatment filter media.

Troubleshooting and Maintenance

Most problems occur with the connections, it can sometimes be hard to push the tubing onto the cones, sometimes fittings are over-tightened, or people use Teflon tape and paste on fittings that do not need it.
If the pump pumps in manual mode and makes a thumping sound, then it is working.
Watch How-To Videos on Our YouTube Channel
https://www.youtube.com/cleanwaterstore

Priming Problems

  1. If you cannot get it to prime, it is either because a fitting is too loose, too tight, or not installed correctly.
  2. While the pump is running (usually, on Manual), observe if the fluid is coming up the tube- if you see the water going up and down in the tubing, this indicates the foot valve is not tight, or you installed the pump too high above the  solution tank, or you mounted the pump improperly.
  3. Sometimes, as mentioned earlier in the guide, it is because the four Allen head bolts on the grey pump head have loosened, and need to be tightened, do not over-tighten.
  4. If the solution has filled the tubing, but it is not discharging, make sure the de-gas is opened, and then close it until the point when it starts pumping.
  5. The tubing going from the outlet/discharge to injection check valve will twitch and move at the same time the pump triggers, that is how you can confirm you are pumping solution.
  6. If this does not work, remove the discharge-to-injection check valve tubing from the outlet fitting, and see if it squirts out of the top- if it does, this indicates that the problem is in the injection check valve, or that you are trying to pump against greater than 100 psi.

Maintenance Tips
Check the pH at least once per month and adjust the J-PRO-22Pump and/or solution strength if needed.
Winterizing: do not let the J-PRO-22Pump or tubing freeze. If you need to winterize, drain the soda ash solution tank and discard solution.
Place the suction of the pump into a bucket of clean water and allow the pump to run until the J-PRO-22 Pump is free of any soda ash solution.
Remove the suction from the water and allow the pump to pump dry. Pump is ready to store.
NOTE: when mixing up the soda ash solution, use only distilled water, water from a reverse osmosis system, or at least softened water. Do not use untreated well water.

Need Assistance?
Call us at 831-462-8500
or email support@cleanwaterstore.com
Spare Parts
These installation parts are included with initial order, but you may wish to have spares on hand, or replace the injection check valve, foot valve or diaphragm later.

Troubleshooting Tips Solutions

Pump not priming
in the solution.| Ensure the suction line is correctly connected and free from leaks. The foot valve should be submerged
Make sure tubing is pushed the conical fitting until the tubing is flush against the end of the fitting and fittings are tightened.
Pump not injecting solution (chlorine, peroxide, soda ash, citric acid etc)| Verify the injection check valve is correctly installed and not obstructed.
Pump losing prime| Inspect if the solution tank is empty or if the foot valve is obstructed.
Pump making loud noise| Pump does make a “ka-thunk” rapping noise when pumping, this is normal. Consider soundproofing the pump with a wooden or styrofoam enclosure. A rapping or clicking noise is common when the pump is operating.
Not sure if my JPRO-22 pump is actually pumping solution| Listen for a ‘ka- thunk” sound when pump is running. If the pump is primed and pumping you will notice the discharge tubing slightly twitching and jerking.
Mark the solution level on the solution tank with a piece of tape. Check again in ‘I to 2 days to see if the level has changed.
Pump sounds like it’s pumping but solution is not going down| Open the priming valve on top of the pump to discharge the solution back into the solution tank. If it starts pumping, it might have lost its prime.
Diaphragm might be worn or torn. Replace diaphragm. For residential use diaphragms typically last 2 to 4 years before requiring replacement.
Solution can pump out through the priming
valve but won’t pump into the actual piping| Ensure the injection check valve is clean and not plugged up.
No sound coming from pump. No lights on control panel when plugged in or powered up| The pump will need to be replaced. Ensure the pump is not exposed to power surges.
Entire solution tank empties each day| This could be due to a vacuum being pulled on the JPRO-22 and your water line sucking solution out of the solution tank. This
is not a pump issue. It’s often caused by a faulty check valve in the well causing water to run back down the well and creating a vacuum on the injection check valve.
Pump failure due to power surges or outages| Power surges or outages that cause pump failure are not covered under warranty. Surge protection is strongly recommended.
Pump failure due to exposure to freezing temperatures, direct sunlight, or rain| If the cause of failure is determined to be from exposure to any of these environments, the pump does not qualify for replacement and will not be covered under warranty.
Pump leaking from front end (liquid end) of pump| Replace diaphragm and oring set. If pump is several years old the pump head may also need to be replaced

www.cleanwaterstore.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

CLEAN WATER STORE User Manuals

Related Manuals