WHADDA WPM352 RTC DS3231 Module User Manual

: June 6, 2024
: WHADDA

Table of Contents

WHADDA WPM352 RTC DS3231 Module User Manual
Introduction
Safety Instructions
General Guidelines
What is Arduino®
Product overview
Specifications
Wiring description
Example program
- References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WHADDA WPM352 RTC DS3231 Module User Manual

WHADDA WPM352 RTC DS3231 Module.jpg

WPM352

Introduction

To all residents of the European Union
Important environmental information about this product

This symbol on the device or the package indicates that disposal of the device after its lifecycle could harm the environment. Do not dispose of the unit (or batteries) as unsorted municipal waste; it should be taken to a specialized company for recycling. This device should be returned to your distributor or to a local recycling service. Respect the local environmental rules.

If in doubt, contact your local waste disposal authorities.

Thank you for choosing Whadda! Please read the manual thoroughly before bringing this device into service. If the device was damaged in transit, do not install or use it and contact your dealer.

Safety Instructions

Read and understand this manual and all safety signs before using this appliance.

For indoor use only.

This device can be used by children aged from 8 years and above, and persons with reduced
physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the device in a safe way and understand the hazards involved. Children shall not play with the device. Cleaning and user maintenance shall not be made by children without supervision.

General Guidelines

Refer to the Velleman® Service and Quality Warranty on the last pages of this manual.
All modifications of the device are forbidden for safety reasons. Damage caused by user modifications to the device is not covered by the warranty.
Only use the device for its intended purpose. Using the device in an unauthorised way will void the warranty.
Damage caused by disregard of certain guidelines in this manual is not covered by the warranty and the dealer will not accept responsibility for any ensuing defects or problems.
Nor Vellemannv nor its dealers can be held responsible for any damage (extraordinary, incidental or indirect) –of any nature (financial, physical…) arising from the possession, use or failure of this product.
Keep this manual for future reference.

What is Arduino®

Arduino® is an open-source prototyping platform based on easy-to-use hardware and software.
Arduino® boards are able to read inputs – light-on sensor, a finger on a button or a Twitter message –and turn it into an output – activating of a motor, turning on an LED, publishing something online. You can tell your board what to do by sending a set of instructions to the microcontroller on the board. To do so, you use the Arduino programming language (based on Wiring) and the Arduino® software IDE (based on Processing). Additional shields/modules/components are required for reading a twitter message or publishing online. Surf to www.arduino.cc for more information

Product overview

The Whadda RTC DS3231 module is a real-time clock that enables accurate timekeeping with
minimum fuss. It uses a DS3231 IC, an extremely accurate RTC chip with a built-in 32 kHz crystal oscillator. The chip also features a basic temperature sensor and alarm clock capability.
The RTC module uses a standard I²C interface and can easily be interfaced with various developments boards (such as an Arduino® compatible board).

Specifications

Supply voltage: 3,3 – 5 V DC
RTC IC: DS3231
RTC accuracy: ± 2 ppm (from 0 °C to +40 °C)
Temperature sensor accuracy: ± 3 °C
Maximum I²C bus frequency: 400 kHz
Backup battery: CR2032
Dimensions (W x L x H): 43,2 x 22,4 x 14,7 mm

Wiring description

FIG 1 Wiring description.JPG

Example program

You can download the example Arduino® program by going to the official Whadda github page:
github.com/WhaddaMakers/RTC-DS3231-module

1. Click the “Download ZIP” link in the “Code” menu:

2. Unzip the downloaded file, and browse to the set_time folder. Open the example Arduino®
sketch ( set_time.ino ) located in the folder.
3. Use the Arduino Library manager to install the DS3231 library, by going to Sketch > Include Library > Manage Libraries… , typing in DS3231 in the search bar and clicking “ Install ”:

FIG 5 Example program.jpg