ipega PG-9097 Wireless Controller User Manual

ipega PG-9097 Wireless Controller

Application Introduction

1. Direct play without any platform or complicated activation to connect.
2. Support Android/ iOS /Tablet/ P31 N-S console and PC
3. Equipped with telescopic phone stand (width 50 – 80mm)
4. Support some cloud gaming platforms.
5. Ergonomic stnicture, comfortable and hand feeling.
6. Programmable, able to map and program trequenfly used action keys or combination keys  to the back button. Enhancing the game control experience.

• Due to the mobile phone system, some mobile phones may not support this device (for example,  mobile phones on tile MediaTek platform cannot support it).
• Due to the official game platform software upgrades or source code changes and other not resist  factors caused some of the game cannot be played or connected with our Gamepad, iPega  company has no responsibility, iPega reserve the right of final interpretation for this.

Instruction for key function

Specifications

1. Working voltage: DC3.7V;
2. Working current : <15 mA;
3. Standby current: <15uA;
4. Working hours: > 15 hours;
5. Charging voltage/ current: DC5V/500mA;
6. Charging hours: 2 hours
7. Wireless 5.0, transmission distance: .;; SM;
8. Battery capacity: 400mAh;
9. Standby time: up to 30days once fully charged;

Phone stand installation & removal step

Installation

1. Align the buckle at the phone stand with the groove  on the top of the condoler (as stowing below).
   

2. Press the phone stand and push down at the same time to install it

Removal

1. Push the phone stand from bottom to top, and then pull it out to remove it.

Direct Play Mode (Android V3)

Press and hold A+ HOME buttons for 2 seconds 10 enter Direct Play Mode (Android ). At this time, the LED1 indicator will flashes quickly, then search “PG-9097′ on Android phone/ tablet BT and pair, Led indicator will be always on after connected successfully!
If you connected before, press the HOME button directly, LED1 indicator will flash slowly, automatically reconnect!

Android direct-connection button mapping function

Check the default operation instructions at ‘www.ipega.hk‘. If you need to reset the game buttons, please download and install “Shooting Plus V3” APP from APP Store/ Google Play Store. remap tile game buttons in the APP and adjust the button position.

ios MFI mode (iOS 13.0 or above)

Press and hold B + HOME buttons for 2 seconds to enter MFI mode. At this time, the LED2 indicator will flashes quickly, then search ‘DUALSHOC 4 Wireless Controller· on IOS phone/ tablet BT and pair, LED2 indicator will be always on after connected successfully!
If you connected before, press the HOME button directly, LED2 indicator will flash slowly, automatically reconnect!

Android Standard mode

Press and hold X + HOME buttons for 2 seconds to enter Android Standard mode. At this time, the LED3 indicator will flashes quickly, then search “PG-9097” on Android phone I tablet/ Android TV BT and pair, LED3 indicator will be always on after connected successfully!
If you connected before, press the HOME button directly, LED3 indicator will flash slowly, automatically reconnect!

Wired mode

Plug flue USB data cable to enter wired mode Support console : PC/ Pal N-S console

1. PC as X-input 360 mode LED1 indicator will on. Press • Home • for 3 seconds to switch to P3 mode and the LED 2 will always on
2. N-S console can identify, once connected the console will auto allocation the LED.
3. P3 console can identify, once connected 1he console will auto allocation the LED; wired P3 console connection, take off the USB data cable to change as wireless mode.

N-S wireless mode

Press & hold R2 + HOME at the same time to enter N-S pairing mode, the LEDs 2 & 3 will flash quickly, it will automatic matching LEDs after successful connection.
The LEDs 2 & 3 will flashing slowly when reconnecting, ij will automatic matching LEDs after successful connection.
When you connected and charging at the same time, the LED light will keep flashes until the controller fully charged.

Programming function

• There is a programming button at the bottom of flue controller.
• The RB/ RT I programming L3 / R3 / key t I can l I -map I a -single )can be action set and key or programmed. multiple keys. ( A/ B/ XIV/ LB/ LT I @ A single programming corresponds to a maximum of 12 key combinations.
• Programming key does not induce TURBO function.
• Power off, sleeping mode or restarted, the controller will remember 1he last program.

Programming method:

• Press end hold the action keys to be set and START at 1he same time. Once the LED light will flash circularly, release the button to enter the programming setting mode;
• Press one or more action keys ( Al B/X/Y /LB/LT/ RB/ RT /L3/R3/ f / l 1-1- or multiple keys form a combination}, press the corresponding programming key again to confirm and exit atomically, Once finished the programming setting, the LED indicator returns as  After default. the programming is successful, the programming key has the same function as a single
• key or multiple keys that have just been programmed and mapped.

Clear programming function:

• Press and hold the programming button to be cleared and START at the same time.
• LED light will flash circularly, release the button;  Press the programming key again to confirm, and exit automatically, and the mode indicator return to the display stale before setting. The programmed key function is cleared.

Vibration function

• Power-on vibration.
• TURBO Adjus1able + left 3D vibration t to increase vibration
• TURBO + left 3D I to reduce vibration
• Three levels of vibration: none/weak/strong
•  When adjusting the vibration, the motor will vibrate with the adjustment for 1 second

Turbo/ Auto function

1. Turbo function include these action buttons (A/ B /XI Y /LB/LT I RB I RT)
2. Setting method: Long press the action button, then press the TURBO to turn on the semi-automatic burst mode; Long press the action button, and then press TURBO twice to tum on the AUTO automatic burst mode; Press 1he action button, and press the TURBO third time to turn off the TURBO/AUTO function;
3. TURBO + minus key for 3 seconds to clear all TURBO/AUTO settings.
4. Powered off, sleeping mode, and restarted the previously set Turtx> function will be automatically cleared. If the Turbo function is enabled, it must be reset.
5. The TURBO function is divided into three levels, TURBO key + right 3D I 10 increase the frequency, TURBO key + right 3D l to decrease the frequency (5 times 10 times 15 times) Simultaneously press and hold TURBO+START for three seconds to clear all TU ABO

Button V1brat1on function

Vibration function include these action buttons (A/ B / X / Y / LB/ LT I RB / RT } Vibration setting :

1. Vibration On: Press and hold the action button, then press 1he L3 button for 2 seconds, the controller will vibrate and the vibration setting will be completed;
2. Vibration Off: press and hold the set vibration key, then press the L3 key for 2 seconds, after  the vibration stopped, the key vibration is canceled successfully;
3.  It will be automatically saved when t?e controller is turned off, no need to set n again for the next time:

Restore Factory Setting
Press and hold TURBO + START for 3 seconds, to clear all TURBO, Vibration, Mapping function etc. restore to factory setting.

Operations mode

Charging/ sleep/ wake up/ off function

1. Charging function
2. When the power is low, the LED 4 indicator flashes quickly;
3. When charging, the LED 4 will be flashes slow;
4. When fully charged, the LED 4 will be always on;
5. The controller does not display charging status when wired;
6. Sleep/ wake up I off function:
7. The gamepad will automatically turn off if no operation within 60 minutes
8. When you need to restart, you need to press the HOME button to wake up then you can reconnect;
9. When the gamepad is turned on, press and hold HOME for 3 seconds 1he product will  1urned off, and all the LED indicators will tum off;

Note:

• Please do not store this product in wet or high-temperature areas.
• Don’t knap, beat, drub, pierce, or try to decompose this product, to avoid unnecessary damage to the product.
• The product has built-in batteries please don’t discard them together with the garbage’s.
• Don’t charge the controller in a place near the fire or other heat source.
• Non professional personnel should not disassemble the product, otherwise will not be covered in the after-sales warranty service.

Accessories list

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>