Tenda N301 Wireless Easy Setup Router Installation Guide
- June 4, 2024
- Tenda
Table of Contents
Install Guide
Wireless N301 Easy Setup Router
Model: N301
Package Contents
- Wireless Router*1
- Power Adapter*1
- Ethernet Cable*1
- Install Guide*1
If any item is incorrect, missing, or damaged, please keep the original
package and contact your dealer for immediate replacement.
You can get the User Guide online at www.tendacn.com
for featured settings of the router.
Figure 1
Figure 2
Connect Your Router (figure 1)
Step 1 Insert the power adapter to your router’s Power port, and plug the
other end into a power outlet.
Step 2 Connect the modem to the Internet port of your router using an
Ethernet cable.
Step 3 Insert your modem’s power adapter into the power interface, and
plug the other end into a power outlet.
Step 4 Connect your computer to the router wirelessly, or via an Ethernet
cable.
Wired: Connect your computer to the router using the included Ethernet
cable.
Wireless: To connect with WiFi, use the WiFi name and password on the
product label.
Either WiFi (SSID) or WiFi password is changed, and devices are required to
reconnect with WiFi manually once again.
Tips
If you access the Internet via an Ethernet cable, follow the steps below:
Step 1: Insert the power adapter into your router’s Power port, and plug
the other end into a power outlet.
Step 2: Insert the Ethernet cable into the router’s Internet port
directly.
Step 3: Connect your computer to the router wirelessly, or via an
Ethernet cable (Refer to Step 4 above).
Configure Your Router (figure 2)
Step 1 Access the wireless router: Open a web browser, type 192.168.0.1 or tendawifi.com in the address bar, and tap Enter on the keyboard.
Step 2 Access the Internet (Follow the instructions and complete the Internet setup. There are three connection types: PPPoE, Dynamic IP, and Static IP. Take PPPoE as an example here.)
- Type the user name and password from your Internet Service Provider.
- Customize your WiFi name and password.
- Done & Enjoy!
Your router’s LED indicators may differ. Please refer to the actual product.
| LED Indicator | Status | Description |
|---|---|---|
| SYS | Blinking | The system is working fine. |
| Off | There are no power supply or router malfunctions. | |
| WLAN | Solid | Wifi Is enabled. |
| Blinking | The Router is transmitting WiFi data. | |
| Off | WiFi is disabled. | |
| 1/2/3 | Solid | The LAN port is well-connected. |
| Blinking | The LAN port is transmitting data. | |
| Off | No link is detected on the LAN port. | |
| WAN | Solid | The WAN port is well-connected. |
| Blinking | The WAN port is transmitting data. | |
| Off | No Ethernet cable is connected to the WAN port. | |
| WPS | Solid | WPS is enabled, or a WPS connection is established. |
| Blinking | The Router is performing WPS negotiation to a client device or |
transmitting data.
Off| WPS is disabled.
Your router’s buttons may differ. Please refer to the actual product.
| Button | Description |
|---|---|
| WPS/ RST | Press and hold it for about 8 seconds and then release it (all LED |
indicators will light up once) to Reset/Login the router to factory default settings.
Press and hold it for 173 seconds, and then release it to enable the WPS
feature. Within 2 minutes, enable the wireless device’s WPS feature to
establish a WPS connection.
Ql: Where should I place my wireless router for optimum performance?****
– A 1: To achieve optimum performance, please pay attention to the
following key points:
– Place it around the central area in which your laptops, smartphones, and
other devices usually surround, and preferably within line of sight to your
wireless devices.
– Put it on an elevated spot such as a high shelf, keeping the number of walls
and ceilings to a minimum between the Router and other clients such as
computers and smartphones.
– Keep it away from electrical devices that are potential sources of
interference, such as ceiling fans, home security systems, or microwaves.
– Keep it away from any large metal surfaces, such as a solid metal door or
aluminum studs.
– Keep it away from other materials such as glass, insulated walls, fish
tanks, mirrors, brick, and concrete that may also affect your wireless signal.
Q2: I cannot log in to the wireless router’s User Interface. What should I do?****
– A2: Please follow the instructions below step by step.
– a. Verify the Ethernet cable between your PC and the router is intact and
well-connected. If not, use another Ethernet cable.
– b. Clear the cache of your browser, or open another web browser.
– c. Double-check the TCP/IP settings on your computer. Verify if it is set to
obtain an IP automatically.
– d. Press and hold the RST button for about 8 seconds, then release it to
restore factory settings; then try to log in again.
– e. Try to log in on another computer, smartphone, or iPad.
FAQ
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference by one of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate this
equipment. This transmitter must not be co-located or operating in conjunction
with any other antenna or transmitter. The manufacturer is not responsible for
any radio or TV interference caused by unauthorized modifications to this
equipment.
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
a minimum distance of 20cm between the radiator & your body.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures. This device complies with EU 1999/5/EC.
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. (2) To
avoid unnecessary radiation interference, it is recommended to use a shielded
R145 cable.
Address Info
Tenda Middle East Electronics Trading LLC P.O. BOX 184105, Dubai, UAE Tenda
Technology GMBH Neumann-Reichardt-Str. 27-33, Haus 12, 22041, Hamburg PT.
Tenda Technology Indonesia Mangga Dua Mall, LT IV, Blok A NO. 65, Jakarta,
Indonesia Tenda Technology Inc 20418E Walnut Dr N,STE 1J&1K, Walnut, CA, USA,
91789
Technical Support
Shenzhen Tenda Technology Co., Ltd.
6-8 Floor, Tower E3, No.1001, Zhongshanyuan Road, Nanshan Global Hotline: (86)
755-27657180 Hongkong Hotline: 00852-81931998 Canada Hotline:
1-888-998-8966 New Zealand Hotline:
800787922 Website: http://www.tendacn.com
District, Shenzhen, China.518052
United Kingdom Hotline: 44 0800 1337 824
Australia Hotline: 1300787922
Skype: Tendasz E-mail: support@tenda.com.cn
Copyright
© 2015 Shenzhen Tenda Technology Co., Ltd. All rights reserved.
Tenda is a registered trademark legally held by Shenzhen Tenda Technology Co.,
Ltd. Other brand and product names mentioned herein are trademarks or
registered trademarks of their respective holders. Specifications are subject
to change without notice.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>