V-TAC VT-81003 LED Dome Light with PIR Sensor Instruction Manual

V-TAC VT-81003 LED Dome Light with PIR Sensor

Product Specifications

• Model: LED Dome Light with PIR Sensor
• SKU: [Insert SKU]
• Power: [Insert Power]
• Lumens: [Insert Lumens]
• Input Voltage: [Insert Input Voltage]
• CRI: [Insert CRI]
• Time Delay: [Insert Time Delay]
• Detection Distance: Up to 6 meters
• Detection Range: [Insert Detection Range]
• Detection Motion Speed: [Insert Motion Speed]
• Working Temperature: [Insert Working Temperature]
• IP Rating: [Insert IP Rating]

Product Usage Instructions

Installation

1. Choose a suitable location to mount the LED Dome Light with a PIR Sensor.
2. Ensure the input voltage matches the requirements of the light.
3. Mount the light securely using appropriate fixtures.

Operation

1. The PIR sensor will detect motion within the specified detection distance.
2. The light will automatically turn on when motion is detected.
3. Adjust the time delay and detection range settings as needed.

Maintenance

1. Regularly clean the light to ensure optimal performance.
2. Check for any loose connections or damage to the sensor.

TECHNICAL DATA

INTRODUCTION & WARRANTY

Thank you for selecting and buying the V-TAC product. V-TAC will serve you the best. Please read these instructions carefully before starting the installation and keep this manual handy for future reference. If you have any other queries, please contact our dealer or local vendor from whom you have purchased the product. They are trained and ready to serve you at your best. The warranty is valid for 5 years from the date of purchase. The warranty does not apply to damage caused by incorrect installation or abnormal wear and tear. The company gives no warranty against damage to any surface due to incorrect removal and installation of the product. The products are suitable for 10-12 Hours Daily operation. Usage of the product for 24 Hours a day would void the warranty. This product is warranted for manufacturing defects only.

Caution, risk of electric shock.

MULTI-LANGUAGE MANUAL QR CODE
Please scan the QR code to access the manual in multiple languages.

This marking indicates that this product should not be disposed of with other household wastes

Points de collecte sur www.guefairedemesdechets.fr

• In case of any query/issue with the product, please reach out to us at: support@v-tac.eu
• For More product range, inquiry please contact our distributor or nearest dealers.
• V-TAC EUROPE LTD. Bulgaria, Plovdiv 4000, bul.L.Karavelow 9B

WARNING

1. Please make sure to turn off the power before starting the installation.
2. Installation must be performed by a qualified person.
3. The light source of this luminaire is not replaceable, when the light source reaches its end of life the whole luminaire should be replaced.
4. For indoor use only.

FUNCTION

• Can identify day and night: The consumer can adjust the working state in different ambient light. It can work in the daytime and at night when it is adjusted to the “sun” position (max). It can work in the ambient light less than 3LUX when it is adjusted to the “moon” position (min). As for the adjustment pattern, please refer to the testing pattern.
• Time-Delay is added continually: When it receives the second induction signal within the first induction, it will restart to time from the moment.
• Adjustable Time Delay: the length of time delay could be set according to the customers’ requirement, the minimum time of this item is 10sec±3sec, and the maximum is 3min±30sec.

INSTALLATION

• Switch off the power.
• Unscrew the plastic screw nut and remove the PC lampshade. (refer to figure1)
• Pass the wire through the hole in the bottom and connect the power wire into the connection-wire column according to the connection-wire diagram. Install the sensor lamp in the position where you need wit ith inflated screws. (refer to figure2)
• Switch on the power and test it.

WIRING DIAGRAM

Remarks: you can slide the switch to adjust the color temperature to 3000K, 4000K, or 6000K.

DIMENSION

SENSOR INFORMATION

TEST

• Turn the TIME knob anti-clockwise on the minimum. Turn the LUX knob clockwise on the maximum (sun).
• Switch on the power; the lamp will have no signal at the beginning. After a Warm-up 30sec, the lamp can start working. If it receives the induction signal, the lamp will turn on. While there is no other induction signal anymore, the lamp should stop working within 10sec±3sec.
• Turn the LUX knob anti-clockwise on the minimum (moon). If the ambient light is more than 3LUX, the lamp should not work. If the ambient light is less than 3LUX (darkness), the sensor will work. Under no induction signal condition, the lamp should stop working within 10sec±3sec.
  Note: when testing in daylight, please turn the LUX knob to ☼ the (SUN) position, otherwise the sensor lamp could not work!

NOTE

• Should be installed by an electrician or experienced person;
• Avoid installing it on the uneven object;
• There should be no hindrance and moving objects in front of the detection windows to affect detection;
• Avoid installing it near air temperature alteration zones such as air conditioning, central heating, etc;
• Considering your safety, please do not open the cover when you find the hitch after installation.
• If there is a difference between the instruction and the function the product has, please give priority to the product, and sorry not to inform you additionally.

TROUBLESHOOTING

The load does not work

• . Please check if the connection wiring of the power and load is correct.
• b. Please check if the load is good.
• c. Please check if the working light sets correspond to ambient light.

The sensitivity is poor

• . Please check if there is any hindrance in front of the detect window now affecting the receiving of the signal.
• b. Please check if the ambient temperature is too high.
• c. Please check if the induction signal source is in the detection fields.
• d. Please check if the installation height corresponds to the height shown in the instructions.
• e. Please check if the moving orientation is correct.

The sensor can not shut off the load automatically

• a. Please check if there is a continual signal in the detection field.
• b. Please check if the time delay is the longest.
• c. Please check if the power corresponds to the instruction.

Frequently Asked Questions

• Q: How can I adjust the time delay on the LED Dome Light with PIR Sensor?
  • A: The time delay can usually be adjusted using the settings on the light itself or through a remote control if provided.
• Q: What is the recommended working temperature for this product?
  • A: The recommended working temperature is [Insert Recommended Working Temperature]. Operating outside this range may affect performance.
• Q: Can the detection range be customized?
  • A: Depending on the model, some LED Dome Lights with PIR sensors allow for customization of the detection range through settings adjustments.

References

• tac.eu

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>