ESKUTE MYT-26 Polluno Plus Electric Bike User Manual
- June 14, 2024
- ESKUTE
Table of Contents
ESKUTE MYT-26 Polluno Plus Electric Bike
Safety Instruction
- Thank you for purchasing the ESKUTE E-BIKE. The E-BIKE feature the latest innovations in technology;
- For safety reasons, it is very important that you read this user’s manual before you operate the bike. Improper handling can reduce its riding performance and most importantly, it will endanger your safety and health;
- Regarding the handling and maintenance of bicycles, reference is made to point 6 of this manual, which is an essential part of the “E-Bike User Manual”!
- Do not at any time dismantle or disassemble any of the above e-bike components.
- Please check all parts are tightened and locked before riding.
- Please make sure that the battery charger and charging plug are always kept dry and never get wet.
- The charger should only be cleaned with a dry cloth. Never use a damp cloth, oil or any other liquid.
Instruction
**Specification
**
Main Parts
Display Operation
- Short press the POWER button to start the display, and then long press for 1-2s after power on to turn it off;
- After turning on the display, press the POWER button once to turn on the light;
- After turning on the display, press the * button to control the assistant level, and each press increases one level; conversely, press the -” button to decrease one level.
- After powering on, press and hold the “-” button for more than 5s to enter 6 km/h cruise. Booster mode. (At the same time, this operation tests whether the motor can work properly. Take care to lift the rear wheels.).
- Press and hold the POWER button and *-” button for 20s at the same time to unbind the E-bikes from all mobile phones (This function is used when you cannot unbind the E-bikes from all mobile phones).
Operation Cautions
- Be careful of the safety use. Don’t attempt to release the connector when charging the battery.
- Avoid the risk of collision.
- Make the display expired ter to void appetizers disorder.
Battery & Charge
Battery and Charger
- A – Capacity display
- B – Charging socket
- C – Battery port
- D – switch
- E – battery lock
- A – Socket (100 ~ 240V) (type will vary,
- B – Charge indicator
- C – Charger
- D – Charging socket
Charge Instruction
- To charge the battery with the bike, simply place the bike within reach of the power supply and plug it in.
- The battery can either be charged while on the bike or the battery can be removed and charged at a place of your convenience.
- The RED light indicates it is in charging and the GREEN light indicates the battery is fully charged. (Please put off plug from wall) Usually the charging time is 5-6 hours depends on the battery capacity remain.
- Warning : Charging time over 10 hours is prohibited. Please keep it away from a high-temperature environment and store it in a cool place.
Charge Environment
When storing the battery for a longer time period, (e.g. during winter time)
it is important to place the fully charged battery on a flat and dry place.
- Keep the battery and charger away from water and heat sources.
- Do not connect positive and negative terminals.
- Keep the battery away from children and pets.
- Use the battery and the charger only for the intended purpose as part of your e-bike.
- Do not cover the battery or the charger, place objects over them or place any objects on them.
- Do not expose the battery or the charger to shocks such as falling. -Stop charging immediately if you notice something unusual.
Attention
- In the unlikely event that the battery catches fire, DO NOT attempt to extinguish the fire with water. Instead, use sand or another fire retardant to extinguish the fire.
- Please charge the battery with the specified charger.
- Do not use or charge the battery at high temperatures and do not place the battery near fire.
- Do not short-circuit the positive (+) and negative (-) terminals of the battery.
- Do not immerse the battery in water or acidic fluid.
- Avoid contact with the battery and the charger during charging. The charger heats up considerably.
- Please note the additional information on the back of the battery case.
- Store the battery in a clean and dry environment and recharge the battery every two months ifyou are not going to use it for a long time.
- Keep the battery out of reach for children.
- Never try to open the battery.
Use
When the battery is lower than 1 bar, the motor will stop working. If only for using the headlights, it will remain in use for about 2 hours. The remaining battery power can be checked by pressing the control button under the LED indicator. The handlebar-mounted display also shows the remaining power when the bike is in use. Perform a full discharge of the battery (ride your e-bike until the battery is completely empty) after 15 normal charges or every three months; this will help to increase the life of the battery. The charging time is about 5-6 hours per charging cycle. Please do not charge the battery for more than 10 hours at a time.
Storage
If the bike is not used for more than a month, it is best to store the battery
as follows:
- At 40% -60% of its capacity, recharge for 30 minutes once a month.
- The temperatures is best maintained between -20°C and 50°C.
If the battery is not in use, it should be checked once a month. At least one LED should blink to indicate that there is still a charge. Charge the battery if necessary. It is important to charge the battery at least every two months. Failure to do so may damage the battery and void the battery warranty.
Installation Instruction
When opening the bike’s carton box, take out the E-bike and use tools to cut off the package strings.
Install the Handlebar
Use the inner hexagon tool to loosen the stem cover and don’t tighten all
bolts immediately before adjusting the handlebar in a property angel and
position.
Then tighten it with a tool
Install Front Wheel
- Take out the front fork protector from the front fork. (Please note: Front fork protector is used to prevent the forks from being deformed during transport. It belongs to the packing material. You can just throw away this accessory!)
- Take out the quick-release from Wheel and unscrew the bolt from the quick-release
- Install the front wheel on the fork. Make sure the fork is attached to the axle and make sure the disc is placed in the middle of the brake.
- Insert quick-release axle into spring and tighten screw (Quick release nut to be at the same end as the brake).
Inflating the tires
- The tire pressure should be checked each time before riding or at least once a week.
- Check the marked area on the sidewalls of the tire, which shows the minimum and maximum tire pressure, and make sure that the tire pressure is in the marked area.If the tire pressure is too low, the wheel may be damaged or the inner bicycle tube pinched, which may result in a flat tire.If the tire pressure inner bicycle tube pinched, is too high, the tire may come loose from the rim and thereby damage the bicycle or injure the rider and people in close proximity.
- It is recommended to use a bicycle pump with a built-in air pressure gauge to ensure that your tire always has the desired and correct tire pressure.
Install the Front Light
Mount the headlight on the front fork bracket with screws
Install Pedals
Check 2 pedals, the one imprinted “L” should install on the left side and “R”
on the right side. Please use a wrench to tighten them.
Install the Seat Post
- Open the seat post and saddle, then install the rear reflector;
- Adjust seat post to the height that suits your riding position best and tighten quick release. (Please make sure that the quick release is tightened firmly.)
Install Battery
Each ESKUTE e-bike comes with two copies of the battery key. Charging the
battery on the bike is likely to result in infrequent use of the battery key
however, it is required for maintenance and repair, so please keep this in
mind when you store your key.
Make sure you always have at least one spare key.
Keep spare keys in a safe place for repairs, maintenance, and emergencies.
Please bring the key with you when you contact your dealer for service or
repair.
- Open the box of battery
- Tube the battery to correct angle and insert the battery into the holder gently, press it down and lock automatically.
- Charging the battery outside the bike
- Insert the key to unlock the battery, and then pull the battery upwards.
- Remove the battery.
- Connect the charger to the battery.
- Connect the charger to a power outlet.
- The charging process can be stopped at any time.
- Disconnect the charger first from the power outlet and then from the battery.
- Replace the battery and make sure it is correctly aligned at the bottom.
- Press the top of the battery until you hear a “click” to make sure the battery is properly secured.
- Pull the key out.
- Your ESKUTE e-bike is ready for use.
Range and Speed Selection
To increase the range, we recommend switching to speeds. For starting and low
speed, it is better to use a lower gear. At higher speeds, a higher gear
should be selected. Reduce the pressure on the pedals during gear shifting for
obtaining stable support and improved range.
- High speed, high gear.
- Low speed, low gear.
- Reduce pressure on the pedals when shifting gears.
Recommendation and Maintenance
Range
The range of a battery charge depends heavily on various conditions, such as
(but not limited to):
- Road conditions, such as road surface and inclination.
- Weather conditions, such as temperature and wind.
- Cycling conditions, such as tire pressure and maintenance level.
- Use of the bicycle, such as acceleration, switching and support level.
- Weight of rider and load.
- Number of charge and discharge cycles.
General Requirements
ESKUTE e-bikes use metal enclosures to protect the electrical components.
Therefore, we strongly advise against using too much water to clean the
housing and parts around them. Use a soft cloth with a neutral solution to
wipe the dirt off the covers. Then wipe everything dry with a clean, soft
cloth.
- Do not use high-pressure cleaners or air hoses for cleaning. It will cause water to get into electrical components, which can lead to malfunctions.
- Do not clean plastic parts with too much water. If the internal electrical parts are affected by water, the insulator can corrode, which can lead to power outages or other problems.
- Do not use soap solutions to clean the metal parts. Non-neutral solutions can lead to discoloration, distortions, scratches,etc.
- Avoid leaving the bike outdoors.
If you are not riding, please keep your bike in a place where it will be protected from snow, rain, sunlight, etc. Snow and rain can lead to corrosion of the bike. Ultraviolet rays from the sun can cause unnecessary color fading or damage the rubber or plastic parts on the bike.
Maintenance Schedule
In order to keep your ESKUTE e-bike in optimal condition and to make your riding experience as pleasant as possible, we strongly recommend that you follow the recommended maintenance schedule. You should carefully read the maintenance plan view it as an important document, and place it next to your bike.
Warranty
- As with all mechanical components, Electronically Power Assisted Cycles (EPAC) are subject to wear and high loads. Different materials and components can respond to wear or fatigue in different ways. If the design life of a component has been exceeded, it may suddenly fail and potentially cause injury. Any form of cracking, scratching or color changing in heavily loaded areas indicates that the component has reached the end of its service life and should be replaced.
- Changes to components of your bike, such as the fork or the frame, can make the particular parts or the entire bike insecure. A poorly installed or modified component can increase the load on all other components, thereby greatly increasing the likelihood of failure. Changes can also negatively affect the handling of the bike, resulting in loss of control, falls and serious injuries. Please do not add, remove or modify any components of your bike in any way. Find a trained bicycle mechanic if necessary. Furthermore, we recommend that you contact us (ESKUTE) in advance before changing or adding any components to ensure the safety of riding.
Important Safety Instructions
- Always wear a helmet while riding. Make sure your helmet complies with local laws. Keep body parts and other objects away from moving bicycle parts that can cause damage, such as wheels and chains. Do not place objects on the battery or the motor. Do not obstruct the drive in any way.
- Always wear sturdy shoes that grip the pedals safely. Never ride barefoot or with sandals.
- Familiarize yourself with the controls of your bike.
- Wear bright, visible clothing that is not so loose that it accidentally gets caught by moving parts of the bicycle or caught by roadside or roadside objects.
- Do not jump on your bike. Jumping on bicycles puts a lot of stress on most components, such as spokes and pedals. One of the most vulnerable parts is the front fork. Riders who insist on jumping will face the risks of both bike damage and serious personal injury.
- Pay attention to your speed and keep it at a level that, for example, is adapted to the current weather conditions. Always remember that there is a direct relationship between speed and control, and speed and component load.
- Always follow the local traffic rules.
- Never ride under the influence of alcohol, medication or drugs.
- If you have any health problems, please consult your doctor before riding.
- Never endanger yourself and others by reckless riding.
- Please note that the braking distance increases under rough road conditions such as gravel or wet surfaces.
- Please check the cable management of the brakes before cycling. Make sure both brakes are in good working order and in good condition. The manufacturer is not liable for incidental or consequential loss or damage due to direct or indirect use of this product.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>