Huizhou RC-36 Bluetooth Voice Remote Control User Manual
- June 14, 2024
- Huizhou
Table of Contents
Huizhou RC-36 Bluetooth Voice Remote Control
Product Information
Specifications
- Product Name : Bluetooth Voice Remote Control
- Model Name: RC-36
- FCC ID: 2BDAL-RC-36
- Bluetooth Remote Control Vendor: 0x0B7A
- Product: 0x0001
- Transmit Power Range: 4.28dBm (EIRP)
- Frequency Band: BLE (2400~2483.5 MHz)
- Modulation Type: GFSK
Product Usage Instructions
Pairing the Remote Control
- Press and hold the [ ] key and [ ] key on the remote control simultaneously for about 3 seconds.
- The indicator on the remote control will start flashing, indicating that it has entered pairing mode.
- Turn on the Bluetooth on your host device (e.g., TV) and search for devices.
- Select and connect to the “RC-36” device name.
- If the pairing is successful, the indicator will stop blinking after a few seconds.
- If you are unable to pair, the indicator will flash twice after 30 seconds and then turn off, exiting pairing mode.
Battery Power Low Indicator
When the battery power is lower than 2.4V, the red light on the remote
control will flash for 3 seconds with a frequency of 1 Hz each time a key is
pressed.
Keeping Remote Control Connected
To ensure a stable connection between the remote control and the TV set,
keep them connected at a distance of 4m for at least 1 hour without
disconnection.
Bluetooth Connection and Back Connection
If there is pairing information and the Bluetooth connection gets
disconnected, follow these steps:
- Press the power key and the pairing combination key simultaneously to not send the back connection broadcast.
- Press any other key to send the back connection broadcast for 5 seconds.
- If the back connection is successful, the indicator will flash 3 times.
Sleep and Wake Up
If there is no data interaction, the remote control will automatically
enter sleep disconnection state after being connected for 1 hour. To wake up
the remote control:
- Press any key to wake up the remote control.
- If still connected, the corresponding key Bluetooth code value will be sent.
- If in the Bluetooth connection disconnect state, it will enter the backconnect state.
- After successful connection, press any key to send the corresponding Bluetooth code value.
FAQ
-
What should I do if I can’t pair the remote control?
If you are unable to pair the remote control, wait for it to flash twice after 30 seconds and then turn off. This indicates that it has exited pairing mode. You can try pairing again. -
How do I know if the pairing was successful?
If the pairing is successful, the indicator on the remote control will stop blinking after a few seconds. -
How do I wake up the remote control from sleep mode?
To wake up the remote control from sleep mode, simply press any key on the remote control. -
What is the battery power low indicator?
When the battery power is lower than 2.4V, the red light on the remote control will flash for 3 seconds with a frequency of 1 Hz each time a key is pressed.
Product description
Instructions
Bluetooth remote control pairing instructions
Press and hold the key] and key on the remote control at the same time for
about 3 seconds to work the indicator flashing, indicating that you have
entered pairing mode. Turn on Host Bluetooth – click host Bluetooth – Search
for devices – Connect to the “RC-36” device name and connect. Stopping
blinking after a few seconds indicates that the pairing was successful. If you
can’t pair up all the time, flash 2 times after 30 seconds and turn off and
exit pairing mode.
Low power alarm
When the battery power is lower than 2. 4V, Every time the user presses a key,
Press= any key, the red light flflashes for 3s, and the frequency is 1Hz
Auto sleep
Keep the remote control connected with the TV set at 4m for at least 1 hour
without disconnection; When there is pairing information and the Bluetooth
connection is disconnected, Press the “power key” and “pairing combination
key” to not send the back connection broadcast. Any other key sends the back
connection broadcast for 5 seconds, the back connection is successful, and the
indicator flflashes for 3 times
sleep and wake up
Without any data interaction, the remote control keeps connected for 1 hour
and then enters into the state of sleep disconnection, press any key to wake
up the remote control, if still connected, then send the corresponding key
Bluetooth code value; If you have entered the Bluetooth connection disconnect
state, you will enter the back connect state,After successful connection Press
any key to send the corresponding Bluetooth code value;
ОТА
When the TV is turned on, the upgrade fifile of the remote controller is
detected. If the upgrade fifile exists, the remote controller performs OTA
upgrade, and the LED lamp flflashes in breathing light Shuo. At this time, the
remote controller can’t be used, and any buttons don’t respond. After the
upgrade is successful, the LED light stops flflashing, and the remote
controller can be used normally at this time. If the upgrade fails, it will be
detected and upgraded again at the next boot. After OTA fails, the LED light
stops flflashing, and the remote controller returns to the old version for
normal operation.
Bluetooth remte control
PID/VID vendor: 0хОВ7А. product: 0×0001
Declaration:
- Hereby, [HuiZhou WanZhiSheng New Energy Technology CO.,LTD] declares that the radio equipment type [Bluetooth voice remote control] is in compliance with
- Directive 2014/53/EU.
- Importer info: XXXXXXX
- Transmit Pover Range (s): 4.28dBm(EIRP)
- Frequency Band (s) : BLE(2400~2483.5 MHz)
- Modulation Type(s )：GFSK
FCC NOTE
- This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference
- this device must accept any interference received, including interference that may cause undesired operation.
- Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed toprovide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energyand, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does causeharmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which thereceiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
- The device has been evaluated to meet general RF exposure requirement
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>