NAPOLEON NEFB36H-BS-1 36 Inch Built In Electric Fireplace Instruction Manual

NAPOLEON NEFB36H-BS-1 36 Inch Built In Electric Fireplace

Product Information

Specifications

• Product Code : NEFB36H-BS-1
• Language : English
• Product Type : ElementTM Electric Fireplace
• Dimensions
  • Front View : H1 x L1 x D1
  • Side View : H0 x L0 x D0
  • Top View : H2 x L2 x L3
• For Indoor Use Only
• Certified to Canadian and American National Standards: CSA C22.2 No. 446 / ULC S12207281
• CSA / Intertek Certified

Safety Information

WARNING: Fire or Explosion Hazard

If the information in these instructions are not followed exactly, a fire or explosion may result causing property damage, personal injury, or loss of life.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.
• Installer: Leave this manual with the appliance
• Consumer: Retain this manual for future reference

Button Battery Warning
This appliance has a remote that requires button batteries that are hazardous to young children.

General Instructions

• Unpack and test the appliance
• Locate and ground the appliance
• Follow minimum clearance and mantel clearances
• Install and finish the appliance
• Connect electrical components
• Operate the appliance using the control panel or remote control
• Maintain and clean the appliance regularly
• Refer to the troubleshooting section for assistance
• Warranty information is provided

Product Usage Instructions

Unpacking and Testing Appliance
Follow the steps below to unpack and test the appliance

1. Remove all packaging materials
2. Inspect the appliance for any damage
3. Test the appliance by plugging it into a power outlet
4. Ensure all functions and controls are working properly

Locating Appliance
To locate the appliance, follow these steps

1. Choose a suitable location for the fireplace
2. Ensure proper ventilation and clearance from combustible materials
3. Place the fireplace on a stable and level surface

Installation and Finishing
To install and finish the appliance, follow these steps

1. Follow the recommended rough framing dimensions
2. Install the fireplace according to the provided instructions
3. If applicable, install the logs (for NEFB42H-BS-1 only)
4. Complete any finishing touches, such as attaching a mantel or surround

Electrical Information
For electrical installation, refer to the provided wiring diagram and follow these steps

1. For a 120V cord plug installation, follow the instructions provided
2. For hard-wiring installation, follow the instructions based on the voltage (120V or 240V)

Operating Instructions
To operate the appliance, follow these steps

1. Use the control panel on the fireplace to adjust settings
2. Alternatively, use the provided remote control to operate the appliance
3. If needed, install batteries in the remote control

Maintenance
To maintain the appliance, follow these guidelines

• Regularly clean the fireplace using a soft cloth and mild detergent
• Ensure the fireplace is turned off and unplugged before cleaning
• Check for any signs of damage or wear and address them promptly

Replacement Parts
If replacement parts are needed, refer to the provided overviews for NEFB36H-BS-1 and NEFB42H-BS-1 models.

Accessories
Optional accessories are available for this appliance. Refer to the provided information for more details.

Troubleshooting
If you encounter any issues with the appliance, refer to the troubleshooting section of the manual for assistance.

Warranty
Warranty information for the appliance is provided in this manual.

FAQ

• Q: Can this appliance be used in a bedroom?
  • A: No, this appliance is for indoor use only and should not be used in a bedroom.
• Q: Are there any chemicals in this product that may cause harm?
  • A: Yes, this product contains chemicals including lead and lead compounds, BBP, and DEHP, which are known to the State of California to cause cancer, birth defects, or other reproductive harm. For more information, please visit www.P65Warnings.ca.gov.

SAFETY INFORMATION

WARNING

FIRE OR EXPLOSION HAZARD

If the information in these instructions are not followed exactly, a fi re or explosion may result causing property damage, personal injury, or loss of life.

• Do not store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance.

INSTALLER
Leave this manual with the appliance

CONSUMER

• Retain this manual for future reference
• This appliance has a remote that requires button batteries that are hazardous to young children.

FOR INDOOR USE ONLY
CERCERTIFIED TO THE CANADIAN AND AMERICAN NATIFIED TO THE CANADIAN AND AMERICAN NATIONAL STTIONAL STANAN CSA C22.2 NO. 46 / UL 2021CSA 22.2 NO. 46 / UL 1278

WARNING

• If equipped with a heater, this appliance can be hot when operated and can cause severe burns if contacted.
• Do not operate appliance before reading and understanding operating instructions. Failure to operate appliance according to operating instructions could cause fi re or injury.
• Do not install damaged, incomplete or substitute components.
• Do not burn wood or other materials in this appliance.
• All electric appliances have hot and arcing or sparking parts inside. Do not use it in areas where a gas line, paint or flammable liquids are present.
• Any safety screen or guard removed for servicing must be replaced prior to operating the appliance.
• It is imperative that the control compartments, circulating blower and its passageway in the appliance are kept clean. The appliance should be inspected before use and at least annually by a qualified service person. More frequent cleaning may be required due to excessive lint from carpeting, bedding material, etc. The appliance area must be kept clear and free from combustible materials, gasoline and other flammable vapors and liquids.
• Under no circumstances should this appliance be modified.
• Do not use this appliance if any part has been under water. Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system which has been under water.
• If equipped with a glass door, do not operate the appliance with the glass door removed, cracked or broken. Replacement of the glass should be done by a licensed or qualified service person. Do not strike or slam shut the appliance glass door.
• Keep the packaging material out of reach of children and dispose of the material in a safe manner. As with all plastic bags, these are not toys and should be kept away from children and infants.
• Servicing should be done only while the appliance is disconnected from the power supply circuit.
• Always unplug appliance when not in use.
• Do not operate this appliance with a damaged cord or plug after the appliance malfunctions, has been dropped or damaged in any manner. Return appliance to authorized service facility for examination, electrical or mechanical adjustment, or repair.
• Do not use outdoors.
• When installing this appliance in a room where water is present, the installation must comply with codes recognizing the increased hazard of electrical shock and electrocution.
• note : This appliance is NOT suitable for installation in a bathroom.
• Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or the like. Arrange cord away from traffic area and where it will not be tripped over.
• Connect to properly grounded outlets only.
• Do not insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric shock or fi re, or damage the appliance.
• It is normal for your electric appliance to produce noise, especially when installed in a quiet space such as a bedroom.

WARNING

• To prevent a possible fi re, do not block air intakes or exhaust in any manner. Do not use on soft surfaces, like a carpet, where openings may become blocked.
• Always plug appliances directly into a wall outlet/receptacle. Never use an extension cord or relocatable power tap (outlet/power strip).
• These appliances are tested and listed for use only with the optional accessories listed in these instructions. Use of optional accessories not specifically tested for this appliance could void the warranty and/or result in a safety hazard.

For appliances equipped with a heater

• Risk of burns. Power to the appliance should be turned off and the appliance allowed to cool before servicing. To disconnect power to the appliance, turn controls to off, then remove plug from outlet.
• Young children should be carefully supervised when they are in the same room as the appliance. Toddlers, young children and others may be susceptible to accidental contact burns. A physical barrier is recommended if there are at risk individuals in the house. To restrict access to an appliance or stove, install an adjustable safety gate to keep toddlers, young children and other at risk individuals out of the room and away from hot surfaces.
• Clothing or other flammable material should not be placed on or near the appliance.
• Due to high temperatures, the appliance should be located out of traffic and away from furniture and draperies.
• Ensure you have incorporated adequate safety measure to protect infants/toddlers from touching hot surfaces.
• Even after the appliance is off, the glass and/or screen will remain hot for an extended period of time.
• Check with your local hearth specialty dealer for safety screens and hearth guards to protect children from hot surfaces. These screens and guards must be fastened to the floor.
• Ensure clearances to combustibles are maintained when building a mantel or shelves above the appliance. Elevated temperatures on the wall or in the air above the appliance can cause melting, discoloration or damage to decorations, a TV or other electronic components.

WARNING : This product can expose you to chemicals including lead and lead compounds, which are known to the State of California to cause cancer, and chemicals include- reproductive harm. for chore information, go to www.swarming sag birth defects or other.

Note
The information throughout this manual is believed to be correct at the time of printing. Wolf Steel Ltd. reserves the right to change or modify any information within this manual at any time without notice. Changes, other than editorial, are denoted by a vertical line in the margin.

General Information

dimensions

L0| L1| L2| L3| H0| H1| H2| D0| D1
---|---|---|---|---|---|---|---|---
NEFB36H-BS-1| 36 1/8″ (918mm)| 33 7/8″ (860mm)| 34 5/8″ (879mm)| 28 7/8″ (733mm)| 31 7/8″ (810mm)| 25 7/8″ (657mm)| 30 3/4″ (781mm)| 11 1/4″ (286mm)| 10 5/8″ (270mm)
NEFB42H-BS-1| 42 1/8″ (1070mm)| 39 7/8″ (1012mm)| 40 5/8″ (1031mm)| 33 1/2″ (851mm)| 31 7/8″ (810mm)| 25 7/8″ (657mm)| 30 3/4″ (781mm)| 14″ (356mm)| 13 3/8″ (340mm)

hardware list

Ref.                     Description                            Quantity

A| Wood Screws| 4
B| Strain Relief| 1
C| Junction Box Cover Plate| 1
D| Wire Nut| 1

listing approvals
This appliance has been tested in accordance with the CSA Standards for fixed and location-dedicated electric room appliances in the United States and Canada. If you need assistance during installation, please contact your local dealer.

note
This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with the latest edition of the National Electrical Code ANSI/NFPA 70 in the United States or the Canadian Electrical Code CSA C22.1 in Canada.

Model No.                NEFB36H-BS-1            NEFB42H-BS-1

Description| 36″ Electric Appliance| 42″ Electric Appliance
Voltage| 120V / 240V
Watts| 1500 / 3000W
Amps| Dedicated 15 AMP Grounded Circuit
Appliance Width| 36 1/8″ (918mm)| 42 1/8″ (1070mm)
Appliance Height| 31 7/8″ (810mm)| 31 7/8″ (810mm)
Appliance Depth| 11 1/4″ (286mm)| 14″ (356mm)
Net Weight| 66.1lbs (30.0kg)| 87.9lbs (39.9kg)
Gross Weight| 74.9lbs (34.0kg)| 106.9lbs (48.5kg)

General instructions

• Prior to plugging your appliance into an electrical outlet, verify that the house circuit breakers for the outlet are on.
• The appliance may emit a slight, harmless odor when first used. This odor is normal and it is caused by the initial heating of internal appliance elements and will not occur again.
• If your appliance does not emit heat when called for, consult the “operation” section of this manual for further information.
• Use with a CSA or UL certified surge protector.
• Do not route the power cord directly underneath the appliance.

This electric appliance meets the construction and safety standards of H.U.D. for application in manufactured homes when installed according to these instructions.
As with most electronic devices, your new electric appliance has been designed to operate at temperatures between 5°C (41°F) and 35° C (95°F). During the colder winter months, allow the appliance to reach room temperature before turning it on.

unpacking and testing appliance
Carefully remove the appliance from the box. Prior to installing the appliance, remove all packaging material and test to make sure the appliance operates properly by plugging the power supply cord into a conveniently located 120V, 15 Amp minimum grounded outlet.

note

• The appliance is factory wired for 120 volt power supply. If 240 volt operation is required, see “electrical information” section.
• Exact packaging location may vary. Some packaging has been hidden for clarity.

Rating plate information

• For rating plate location, see “label location” section.
• This illustration is for reference only. Refer to the rating plate on the appliance for accurate information.

note
The rating plate must remain with the appliance at all times. It must not be removed.

label location

locating appliance

WARNING

• Due to high temperatures, this electric appliance should be located out of traffic. Keep combustible materials such as furniture, pillows, bedding, papers, clothes and curtains at least 36” (91.4cm) from the front of the appliance.
• Never locate this electric appliance where it may fall into a bathtub or other water container.
• Wear safety gloves and safety glasses for protection during installation and maintenance.
• To prevent contact with sagging or loose insulation, the electric appliance must not be installed against vapor barrier or exposed insulation. Localized overheating could occur and a fire could result.
• Do not expose the electric appliance to the elements (such as rain, etc.).

grounding appliance

• This appliance is for use on 120 volts and 240 volts. The cord has a plug as shown in (A). An adapter as shown in (C) is available for connecting three-blade grounding plugs to two-slot receptacles, as shown in (B).
• The green grounding plug extending from the adapter must be connected to a permanent ground such as a properly grounded outlet box. The adapter should not be used if a three-slot grounded receptable is available.

To disconnect the appliance, turn controls to off, then remove plug from outlet.

Grounding Methods

Note
This appliance must be connected to a dedicated 15 amp circuit. The use of an extension cord is NOT permitted.

Installation and finishing

WARNING

• Risk of fi re! The power cord must not be pinched against a sharp edge. Secure cord to avoid tripping or snagging to reduce the risk of fi re, electric shock, or personal injury. Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar items. Arrange cord away from traffi c areas and where it will not be tripped over.
• Risk of fi re! To prevent a possible fi re, do not block air intake or exhaust in any manner. Do not use on soft surfaces where openings may become blocked.
• Risk of fi re! Do not blow or place insulation against the appliance.
• This electric appliance is tested and listed for use only with the approved optional accessories. Use of optional accessories not specifi cally tested for this electric appliance could void the warranty and/or result in a safety hazard.
• If the information in these instructions is not followed exactly, a fi re or explosion may result causing property damage, personal injury, or death. Do not store or use gasoline or other fl ammable vapors in the vicinity of this or any other appliance.
• This appliance is heavy. It is highly recommended that two people install this appliance.
• If your appliance is equipped with a heater, ensure the heater vents cannot, in any way, be covered as it may create a fi re hazard.
• Do not run the power cord horizontally, directly below the appliance.

Your NEFB36H/42H-BS-1 is a recessed appliance. Select a suitable location that is not susceptible to moisture and is away from drapes, furniture and high traffic areas.

Note
Follow all national and local electrical codes.

Minimum clearance to combustibles

Measurements are taken from the glass front.

Bottom| 0″| Top| 2″ to mantel
Sides| 0″| Top| 2″ to ceiling
Back| 0″| |

Note
The power switch is located on the upper right hand side of the appliance. Ensure to maintain access to this switch at all times.

Minimum mantel clearances

WARNING
When using paint or lacquer to finish the mantel, the paint or lacquer must be heat resistant to prevent discoloration.

Rough framing

WARNING
Select a location that is not prone to moisture and is located at least 36″ (91.4cm) away from combustible materials such as curtains, drapes, furniture, bedding, paper, etc.

Note

• It is recommended to complete finishing of the wall before fully securing the appliance.
• Once the rough framing and the finishing materials have been prepared and the power has been routed to the right side of the recess, the appliance may be installed.
• The electrical connection must be made prior to placing the appliance into position (see “electrical information” section).
• Have two people lift the appliance into position.
• In order to avoid the possibility to exposed insulation or vapour barrier coming in contact with the appliance body, it is recommended that the walls of the appliance enclosure be “finished” (i.e. drywall / sheet rock, etc.) as you would finish any other outside wall of a home. This will ensure that clearance to combustibles is maintained within the enclosure.

ROUGH FRAMING

| A| B| C| D| E| F| G
---|---|---|---|---|---|---|---
NEFB36H-BS-1| 11″ (279mm)| 35 1/2″ (902mm)| 31 1/4″ (794mm)| 35 1/2″ (902mm)| 35 1/2″ (902mm)| 50 1/4″ (1276mm)| 35 1/2″ (902mm)
NEFB42H-BS-1| 13 3/4″ (349mm)| 41 1/2″ (1054mm)| 31 1/4″ (794mm)| 41 1/2″ (1054mm)| 41 1/2″ (1054mm)| 58 3/4″ (1492mm)| 41 1/2″ (1053mm)

1. Remove the front decorative cover held in place by 2 magnets (Fig. 3-1).

2. With one hand on the glass door to prevent it from falling, remove the 2 screws holding the glass door in place (Fig. 3-2).

3. Carefully lift the glass door out of the 2 slots in the bottom of the firebox (Fig. 3-3). Set the glass door on a soft, non-abrasive surface.

4. FOR NEFB36H-BS-1 ONLY : Remove the 4 screws holding the log set in place (Fig. 3-4) then carefully re- move the log set. Set the log set aside (Fig. 3-5) and discard the 4 screws.

5. Complete hard-wiring (see “electrical information” section).
   note
   It is recommended to complete finishing of the wall before fully securing the appliance (Fig. 3-6).

6. Carefully lift the appliance into the rough-in framing (Fig. 3-7).

7. After the appliance is inserted into the rough-in frame to position, secure the appliance to the rough-in framing by installing 4 screws (supplied) through one of the three holes of the mounting tabs from the inside of the ap-pliance (Fig. 3-8).

8. Remove the 4 screws holding the back retainers in place (Fig. 3-9). Set the screws and retainers aside (Fig. 3- 10).

9. Place the brick panels into the bottom retainers and behind the side retainers (Fig. 3-11).

10. Re-install the 2 back retainers by re-installing the 4 screws previously removed in step 8 (Fig. 3-12 and 3-13).

11. FOR NEFB36H-BS- 1: Re-install the log set without reinstalling the 4 screws removed in step 4 (Fig. 3-14). FOR NEFB42H-BS-1: Install the log set (see “log installation” section for details).

12. Re-install the glass door (Fig. 3-15 and 3-16).

13. Re-install the front decorative cover held in place by 2 magnets (Fig. 3-17).

log installation (for NEFB42H-BS-1 only)

WARNING

• Power supply service must be completed prior to finishing to avoid reconstruction.
• Heat vents and air openings cannot be covered in any circumstances.

COMPLETED LOG SET. CAREFULLY READ THE NEXT PAGES FOR INSTALLATION DETAILS.

1. Install crystal media by applying an even layer of crystals from side to side.
2. Install log A (see below for details).
3. Install log B to the right of log A (see below for details). LOG A & B: DETAILED INSTALLATION VIEW
4. Install log C, resting it along the top left end of log A (see below for details). LOG C: DETAILED INSTALLATION VIEW
5. Install log D, resting it along the centre of the front grate (see next page for details).
6. Install log E, resting it on the top right end of log B (see next page for details). LOG D & E: DETAILED INSTALLATION VIEW
7. Install log F, resting it along the left end of the grate (see below for details).
8. Install log G, resting it along the right end of thecgrate (see below for details). LOG F & G: DETAILED INSTALLATION VIEW

Electrical information

120V cord plug installation
The factory default setting is 120 volt cord plug installation configuration. Simply plug the appliance to a grounded 120V, 15 amp outlet box.

Note
This appliance must be connected to a dedicated 15 amp circuit. The use of an extension cord is NOT permitted.

Wiring diagram

WARNING
Turn off the appliance completely and let cool before servicing. Only a qualified service person should service and repair this electric appliance.

Hard-wiring installation

WARNING
Turn off the appliance completely and let cool before servicing. Only a qualified service person should service and repair this electric appliance.

HARD-WIRING CONNECTION

• If it is necessary to hard-wire this appliance, a qualified electrician must remove the cord connection, and wire the appliance directly to the household wiring. The wire and power supply breaker must be rated for 120V, minimum 15 amps.
• This appliance must be electrically wired and grounded in accordance with local codes or, in the absence of local codes, with the latest edition of the National Electrical Code ANSI/NFPA 70 in the United States or the Canadian
• Electrical Code CSA C22.1 in Canada.

120V hard-wiring installation

1. Remove the 4 screws securing the cord and cover plate to the side of the firebox.
2. Unscrew the wire nuts securing the power supply cord.
3. Install the new strain relief (supplied) (Fig. 4-1) into the new cover plate (supplied) and feed the 14/2 conductor wire through the strain relief.
4. Connect the ground/bond wires together.
5. Connect L1 to L1 of the appliance.
6. Connect the supply N wire to the two N wires in the junction box. Do not connect the L2 wire.
7. With wires secured, carefully feed the wires into the firebox and re-secure the cover plate.

240V hard-wiring installation

1. Remove the 4 screws securing the cord and cover plate to the side of the firebox.
2. Unscrew the wire nuts securing the power supply cord and the L2 wire.
3. Install the new strain relief (supplied) (Fig. 4-2) into the new cover plate (supplied) and feed the 14/3 conductor wire through the strain relief.
4. Connect the ground/bond wires together.
5. Connect L1 to L1 of the appliance, connect the supply N wire to the single white N wire in the firebox. Connect the L2 wire to the L2 wire of the appliance.
6. Screw the wire nuts onto the blue N wire. Do not connect supply wires to this wire.
7. With wires secured, carefully feed the wires into the firebox and re-secure the cover plate.

Operating instructions

WARNING
Ensure the house circuit breakers for the circuit supply are turned on. When initially connecting the appliance to a power source, the appliance will make a beeping sound to indicate standby mode.

Once the appliance has been plugged into a grounded electrical outlet or hard- wired to a dedicated 120V or 240V power supply, it is ready to operate.

Operating control panel

Operating remote control

Note
When operating the remote control, it must be directed towards the front centre of the appliance.

Remote battery installation

WARNING

• This remote control requires button batteries that are hazardous to young children.
• WARNING! KEEP BATTERIES OUT OF REACH OF CHILDREN. Swallowing may lead to serious injury or death in as little as 2 hours due to chemical burns and potential perforation of the esophagus.
• If you suspect your child has swallowed or inserted a button battery, immediately seek urgent medical assistance.
• Examine devices and make sure the battery compartment is correctly secured (i.e. that the screw or other mechanical fastener is tightened).
• Do not use if compartment is not secure. Dispose of used button batteries immediately and safely.
• Flat batteries can still be dangerous.
• Tell others about the risks associated with button batteries and how to keep their children safe.
  • To replace the existing battery, remove the  battery holder.
  • To remove the battery holder, turn remote onto front side and press the left side lever towards the center while pulling the battery holder out using the slot provided.
  • Replace existing battery, type CR 2025, with a new battery and reinstall the battery holder into the remote by sliding it into position.
  • Battery holder is secure into the remote control when a clicking noise is heard.

Batteries must be disposed of according to the local laws and regulations. Some batteries may be recycled, and may be accepted for disposal at your local recycling center. Check with your municipality for recycling instructions.

Maintenance

WARNING

• Always turn the heater off and unplug the power cord from the outlet before cleaning, performing maintenance, or moving this appliance. Failure to do so could result in electric shock, fire, or personal injury.
• Never immerse in water or spray with water. Doing so could result in electric shock, fire, or personal injury.

Metal

• Buff using a soft cloth, slightly dampened with a citrus oil-based product.
• Do not use brass polish or household cleaners as these products will damage the metal trim.

Glass

• Use a good quality cleaner sprayed onto a cloth or towel. Dry thoroughly with a paper towel or lint-free cloth.
• Never use abrasive cleaners, liquid sprays, or any cleaner that could scratch the surface.

Vents

• Use a vacuum or duster to remove dust and dirt from the heater and vent areas.

Plastic

• Wipe gently with a slightly damp cloth and a mild solution of dish soap and warm water.
• Never use abrasive cleaners, liquid sprays, or any cleaner that could scratch the surface.

Replacement Parts

WARNING
Failure to position the parts in accordance with this manual or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

• Contact your dealer for questions concerning prices and policies on replacement parts. Normally, all parts can be ordered through your Authorized dealer / distributor.
• For warranty replacement parts, a photocopy of the original invoice will be required to honor the claim.

When ordering replacement parts always give the following information

• Model & Serial Number of appliance
• Installation date of appliance
• Part number
• Description of part
• Finish
• Parts, part numbers, and availability are subject to change without notice.
• Parts identified as stocked will be delivered within 2 to 5 business days for most delivery destinations.
• Parts not identified as stocked will be delivered within a 2 to 4 week period, for most cases. Parts identified as ‘SO’ are special order and can take up to 90 days for delivery.

For after-sales service, please call 1-866-820-8686.

Note
Care must be taken when removing and disposing of any broken glass or damaged components. Be sure to vacuum up any broken glass from inside the appliance before operation.

NEFB36H-BS-1 overview

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED.

• Items not illustrated.

NEFB42H-BS-1 overview

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED.

• Items not illustrated.

Accessories

ITEMS MAY NOT APPEAR EXACTLY AS ILLUSTRATED.

Troubleshooting

WARNING
Turn off the appliance completely and let cool before servicing. Only a qualified service person should service and repair this electric appliance.

Warranty

• Napoleon electric appliances are manufactured under the strict Standard of the world recognized ISO 9001 : 2015 Quality Management System.
• Napoleon products are designed with superior components and materials and assembled by trained craftsmen who take great pride in their work. Once assembled, the complete appliance is thoroughly inspected by a qualified and authorized installer, service agency, or supplier before packing to ensure that you, the customer, receive the quality product that you expect from Napoleon.

Napoleon Electric Appliance Premium Warranty

• Electrical components and wearable parts are covered and Napoleon will provide replacement parts free of charge during the first 2 years of premium warranty. This covers: fan/heaters, motors, switches, nylon bearing components, remote controls, and LED lights.*
• Light bulbs and fuses are NOT covered by the warranty.
• In the first year only, any labor related to warranty repair is covered.
• Construction of models vary. Warranty applies only to components included with your specific appliance.

Conditions and Limitations

• Napoleon warrants its products against manufacturing defects to the original purchaser only. Registering your warranty is not necessary. Simply provide your proof of purchase along with the model and serial number to make a warranty claim.

• Provided that the purchase was made through an authorized Napoleon dealer, your appliance is subject to the following conditions and limitations

• Warranty coverage begins on the date of original installation.

• This factory warranty is non-transferable and may not be extended whatsoever by any of our representatives.

• Installation must be done in accordance with the installation instructions included with the product and all local and national building and fi re codes.

• This premium warranty does not cover damages caused by misuse, lack of maintenance, accident, alterations, abuse, or neglect and parts installed from other manufacturers will nullify this warranty.

• This premium warranty further does not cover any scratches, dents, corrosion, or discoloring caused by excessive heat, abrasive and chemical cleaners, nor chipping on porcelain enamel parts, mechanical breakage of PHAZER™ logs.

• In the first 2 years only, this warranty extends to the repair or replacement of warranted parts which are defective in material or workmanship, provided that the product has been operated in accordance with the operation instructions and under normal conditions.

• After the fi rst year, Napoleon will not be responsible for installation, labor, or any other expenses related to the reinstallation of a warranted part, and such expenses are not covered by this warranty. Notwithstanding any provisions

• contained in the Premium Warranty, Napoleon responsibility under this warranty is defined as above, and it shall not in any event extend to any incidental, consequential, or indirect damages.

• This warranty defines the obligations and liability of Napoleon with respect to the Napoleon electric appliance and any other warranties expressed or implied with respect to this product; its components or accessories are excluded.

• Napoleon neither assumes, nor authorizes any third party to assume, on its behalf, any other liabilities with respect to the sale of this product.

• Any damages to appliance, brass trim or other component due to water, weather damage, long periods of dampness,
  condensation, damaging chemicals, or cleaners will not be the responsibility of Napoleon.

• Napoleon reserves the right to have its representative inspect any product or part thereof prior to honoring any warranty claim.

• All parts replaced under the Premium Warranty Policy are subject to a single claim.

• All parts replaced under the warranty will be covered for a period of 90 days from the date of their installation.

• The manufacturer may require that defective parts or products be returned or that digital pictures be provided to support the claim. Returned products are to be shipped prepaid to the manufacturer for investigation. If a product is found to be defective, the manufacturer will repair or replace such defect.

• Before shipping your appliance or defective components, your dealer must obtain an authorization number. Any merchandise shipped without authorization will be refused and returned to sender.

• Shipping costs are not covered under this warranty.

• Additional service fees may apply if you are seeking warranty service from a dealer.

All specifications and designed are subject to change without prior notice due to on-going product improvements. Napoleon is a registered trademark of Wolf Steel Ltd.

NAPOLEON CELEBRATING OVER 40 YEARS OF HOME COMFORT PRODUCTS

• 7200, Route Transcanadienne, Montréal, Québec H4T 1A3
• 24 Napoleon Road, Barrie, Ontario, Canada L4M 0G8
• 214 Bayview Drive, Barrie, Ontario, Canada L4N 4Y8
• 103 Miller Drive, Crittenden, Kentucky, USA 41030
• De Riemsdijk 22, 4004 LC Tiel, The Netherlands
• Phone : 1-866-820-8686
• napoleon.com

References

• Napoleon® Canada | Barbecue Grills, Fireplaces, Heating & Cooling
• Napoleon® Canada | Barbecue Grills, Fireplaces, Heating & Cooling
• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>