ERGOTRON Thin Client Mount User Guide
- June 7, 2024
- ERGOTRON
Table of Contents
User’s Guide
Thin Client Mount
Features & Specifi cations
< 6 lbs. (2.7 kg)
CAUTION: DO NOT EXCEED THE MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
IMPORTANT! This
product adds an additional 2 lbs. (1 kg) to your mounting solution. When
mounting between a monitor and VESA plate, the mounting solution’s monitor
weight capacity must be reduced by 2 lbs. (1 kg) when using standard monitors
and thin clients which when combined are less than or equal to 2.5″ (64 mm)
thick. Additional reduction will be required if the combined monitors and
thin client are greater than 2.5″ (64 mm) thick.
For the latest User Installation Guide please visit:
www.ergotron.com
User’s Guide
www.ergotron.com
USA 1-800-888-8458
Europe -32 033-45 45 600
China 86-769-86018920
Components
Follow desired mounting application instructions.
1 Attach bump-ons as shown.
2 Install Portrait/Landscape rotation stop screw.
Insert the provided washer and one of the three provided rotation stop screws
: M3x10 mm, M3.5x8mm, or M4x10mm depending on the diameter of the hole in your
VESA plate.
WARNING! Thin Client may fall out of brackets. Install the Portrait/Landscape rotation stop screw to keep monitor from rotating through the portrait/landscape rotation. Failure to follow these instructions may result in the Thin Client falling out of the brackets and could result in equipment damage and/or personal injury.
3 Attach bracket shown to VESA mount.
NOTE : Using the strap and buckle is optional. If you would like to include the strap and buckle, make sure the strap is between the VESA mount and the bracket when attaching, as shown.
4 Attach bracket to monitor.
NOTE : Using the strap and buckle is optional. If you would like to include the strap and buckle, make sure the strap is between the bracket and the monitor when attaching, as shown. This installation step requires 2 people.
5 Attach brackets.
6 Attach Thin Client.
7 Secure Thin Client.
a. Loosen knobs.
b. Push brackets together.
c. Tighten knobs with pliers as needed.
8 If you are using the strap and buckle, clip buckle together and tighten strap.
1 Attach bump-ons as shown.
2 Attach bracket shown to Wall Track bracket.
NOTE : Leave enough space between brackets to allow sliding onto Wall
Track.
3 Attach brackets to Wall Track.
4 Tighten screws to secure brackets to Wall Track at desired height.
5 Attach brackets.
6 a. Attach Thin Client to brackets.
Secure Thin Client.
b. Loosen knobs.
c. Push brackets together.
d. Tighten knobs with pliers as needed.
7 If you want to use the optional strap and buckle:
a. Wrap the strap around the brackets and Thin Client then clip buckle
together.
b. Tighten strap.
NOTE : If Thin Client is mounted on a pole, this may limit the amount of arm rotation.
1 Attach bump-ons as shown.
2
a. Attach bracket shown to pole and pole clamp.
b. Attach brackets.
3
a. Attach Thin Client to brackets.
Secure Thin Client.
b. Loosen knobs.
c. Push brackets together.
d. Tighten knobs with pliers as needed.
4
If you want to use the optional strap and buckle:
a. Wrap the strap around the brackets and Thin Client then clip buckle
together.
b. Tighten strap.
1 Attach bump-ons as shown.
2 Mark mounting holes in desired location using bracket shown.
3 Drill holes.
TIP: To ensure proper depth, place a piece of tape on the drill bit 0.75″ (19
mm) from the tip.
4 Attach bracket shown.
NOTE : Using the strap and buckle is optional. If you would like to include the strap and buckle, make sure the strap is between the desk and the bracket when attaching, as shown.
5 Attach brackets.
6 Attach Thin Client.
7 Secure Thin Client.
a. Loosen knobs.
b. Push brackets together.
c. Tighten knobs with pliers as needed.
8 If you are using the optional strap and buckle:
a. Wrap the strap around the brackets and Thin Client then clip buckle
together.
b. Tighten strap.
Set Your Workstation to Work For YOU!
Learn more about ergonomic computer use at: www.computingcomfort.org
Height Position top of screen slightly below eye level.
Position keyboard at about elbow height with wrists fl at.
Distance Position screen an arm’s length from face—at least 20” (508mm).
Position keyboard close enough to create a 90˚ angle in elbow.
Angle Tilt screen to eliminate glare.
Tilt the keyboard back 10° so that your wrists remain fl at.
To Reduce Fatigue
Breathe – Breathe deeply through your nose.
Blink – Blink often to avoid dry eyes.
Break • 2 to 3 minutes every 20 minutes
• 15 to 20 minutes every 2 hours.
Service and Warranty
For service and warranty visit www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
NOTE : When contacting customer service, reference the serial number.
ERGO-mon.
© 2013 Ergotron, Inc. All rights reserved.
While Ergotron, Inc. makes every effort to provide accurate and complete
information on the installation and use of its products, it will not be held
liable for any editorial errors or omissions (including those made in the
process of translation from English to another language), or for incidental,
special or consequential damages of any nature resulting from furnishing this
instruction and performance of equipment in connection with this instruction.
Ergotron, Inc. reserves the right to make changes in the product design and/or
product documentation without notification to its users. For the most current
product information, or to know if this document is available in languages
other than those herein, please contact Ergotron. No part of this publication
may be reproduced, stored in a retrieval system, or transmitted in any form or
by any means, electronic, mechanical, photocopying, recording or otherwise
without the prior written consent of Ergotron, Inc.,1181 Trapp Road, Eagan,
Minnesota, 55121, USA Patents Pending and Patented U.S. & Foreign. Ergotron is
a registered trademark of Ergotron, Inc.
Americas Sales and Corporate Headquarters
St. Paul, MN USA
800-888-8458
+1-651-681-7600
www.ergotron.com
sales@ergotron.com
EMEA Sales
Annersfoort, The Netherlands
+31 33 45 45 600
www.ergotron.com
info.eu@ergotron.com
APAC Sales
Tokyo, Japan
www.ergotron.com
apaccustomerservice@ergotron.com
Worldwide OEM Sales
www.ergotron.com
info.oem@ergotron.com
888-97-341-G-01 rev. C • 02/14
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>