BCF 661383 Air Mattress Velour Queen Instructions
- June 14, 2024
- BCF
Table of Contents
BCF 661383 Air Mattress Velour Queen
PLEASE READ CAREFULLY TO ENSURE YOUR SAFETY
- PLU: 661383 CODE: LZY1004
- DESCRIPTION: AIR BED VELOUR QUEEN BCF
- INFLATED DIMENSIONS
- L200 x W150 x H24cm
- DEFLATED DIMENSIONS
- L195 x W146cm
Measured from the top panel before first inflation from top seam to bottom seam and left seam to right seam.
INFLATED CONDITIONS
Air Bed dimensions are measured in a 25°C controlled, indoor environment once the air bed is fully inflated at its firmest comfort level, using a manual hand pump. Due to the properties of PVC, this measurement is likely to vary based on your environment, inflating apparatus, and desired level of mattress firmness. We allow a tolerance of +/- 4.0% of our air bed’s dimensions when inflated under our control conditions.
IMPORTANT SAFETY INFORMATION AND WARNINGS
- Adult supervision is required for inflation, deflation, and maintenance. Follow all safety instructions to avoid serious injury.
- This is not a toy. Please ensure that children are under adult supervision when using this product.
- Remove all sharp objects from area where bed will be set up and used. Bed may puncture.
- Do not step or jump on bed or use as a trampoline.
- Place bed in a safe area before use, making sure that there are no sharp edges, step drops or breakable items nearby. Use on flat surfaces only. Bed may tip over on uneven surfaces.
PVC STRETCH
Not all PVC is BCF quality but all PVC material naturally stretches when pressure is first applied. For your first few uses you may find, that it seems the air bed has lost air during the night. Especially if the bed has been in the sun or you enjoy a high pressure, high support feel of your air bed. Your brand new PVC air bed has simply stretched to the optimum level. No air has been lost during the night. During the first few uses the PVC will continue to stretch naturally until it reaches this optimum level and will now maintain the original pressure throughout the night. If after a few trips you notice the air bed is still losing pressure, contact your local BCF store stockist for more information.
INFLATION
Place your rolled-up bed on the floor or other surface free of obstructions or sharp objects. Open the protective valve cap. Use a manual or powered pump with correct size adaptor. Turn pump off and replace valve cap when bed is fully inflated.
DEFLATION
Open valve cap, then roll the bed completely until all the air is expelled.
When the bed is completely rolled flat replace the valve cap.
CARE & MAINTENANCE
- Check the air level of the AIR BED occasionally. If more than one person is using the AIR BED at the same time, less air may be required for comfort. Experience will suggest the best air levels.
- In case of the velour gets wet or dirty, clean it thoroughly with soap and water before letting it air dry. Do not use chemicals, scouring powder or any other abrasive.
- Avoid exposing the AIR BED to extreme temperatures. Inflate at room temperature.
- Avoid over-inflating the AIR BED.
- Be careful of sharp objects that can damage the bed’s material.
REPAIRING
If the air bed surface is damaged, use the provided repair patch.
To repair
- Completely deflate the air bed.
- Clean and dry the damaged area.
- Apply a repair patch and smooth out any air bubbles.
Note: Never use other liquid glue or adhesive fabric, only use the repair patch like the provided one.
WARNING
- This bed is not for use by children under three (3) years of age.
- The product is intended for use as a bed only. It is not a toy. It is NOT intended for pool use. It is not a flotation device.
- Do not stand, jump or walk on the bed as it may result in personal injury or damage to the bed.
- Do not place near or against heaters, open flame or other hot objects.
- Bed may puncture. Do not place bed on abrasive surfaces or in contact with sharp or protruding objects.
- Do not use for infants or persons with limited mobility. They may roll off the mattress and become entrapped between the mattress and the wall.
- This furnishing has not been evaluated for flammability or cigarette ignition resistance.
PLU: 661383 CODE: LZY1004
Manufactured and packaged for SRGS PTY LTD
ABN 23 113 230 050
6 Coulthards Avenue
Strathpine QLD 4500, Australia
MADE IN CHINA
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>