ergotron HVN0RQLWRU HX Wall Mount Monitor Arm User Guide
- June 14, 2024
- ERGOTRON
Table of Contents
HX
Desk Monitor Arm With Heavy Duty Tilt
HVN0RQLWRU HX Wall Mount Monitor Arm
Includes Constant Force™ Technology
www.ergotron.com
USA: 1-800-888-8458
Europe: +31 (0)33-45 45 600
China: 400-120-3051
Japan: japansupport@ergotron.com
Tools Needed
NOTE: Determine if arm will typically collapse to the left or right before installation.
Adjustment Step
Important! You will need to adjust this product after installation is complete. Make sure all your equipment is properly installed on the product before attempting adjustments. This product should move smoothly and easily through the full range of motion and stay where you set it. If movements are too easy or difficult or if product does not stay in desired positions, follow the adjustment instructions to create smooth and easy movements. Depending on your product and the adjustment, it may take many turns to notice a difference. Any time equipment is added or removed from this product, resulting in a change in the weight of the mounted load, you should repeat these adjustment steps to ensure safe and optimum operation.
8 Adjustment Step
CAUTION: DO NOT remove screw. Removing screw may cause damage to equipment.
|
I Increase Lift Strength
If the mounted weight is too heavy or this product does not stay up when
raised, then you’ll need to increase Lift Strength:| Decrease Lift
Strength
If the mounted weight is too light or this product does not stay down when
lowered, then you’ll need to decrease Lift Strength:
Lift – Up and down
|
I Increase Lift Strength
If the mounted weight is too heavy or this product does not stay up when
raised, then you’ll need to increase Lift Strength:| Decrease Lift
Strength
If the mounted weight is too light or this product does not stay down when
lowered, then you’ll need to decrease Lift Strength:
Monitor Pan – Left and Right
|
Increase Friction
If this product moves too easily, then you’ll need to increase friction:|
Decrease Friction
If this product is too difficult to move, then you’ll need to decrease
friction:
Safety
Warning: Because mounting surface materials can vary widely, it is
imperative that you make sure mounting surface is strong enough to handle
mounted product and equipment.
Caution: Leave enough slack in cable to allow full range of motion.
To avoid the potential to pinch cables it is important to follow the cable
routing instructions in this manual. Failure to follow these instructions may
result in equipment damage or personal injury.
Remove monitors before loosening desk attachment.
Move Arm to highest postition before removing equipment or serious personal injury and/or equipment damage may occur
WARNING! Stored Energy Hazard: The arm mechanism is under tension and will move up rapidly, on its own, as soon as attached equipment is removed. For this reason, DO NOT remove equipment unless the arm has been moved to the highest position! Failure to follow this instruction may result in serious personal injury and/or equipment damage!
CAUTION: For Desk Clamp installations: Do Not rotate display past edge of desk
Weight Capacity:
For displays 6″-12″ (152-305 mm) deep.
CAUTION: DO NOT EXCEED MAXIMUM LISTED WEIGHT CAPACITY. SERIOUS INJURY OR
PROPERTY DAMAGE MAY OCCUR!
For the latest User Installation Guide please visit:
www.ergotron.com
For Warranty visit:
www.ergotron.com/warranty
For Service visit: www.ergotron.com
For local customer care phone numbers visit: http://contact.ergotron.com
Learn more about ergonomic computer use at: www.ergotron.com/ergonomics
NOTE: When contacting customer service, reference the serial
number.
www.ergotron.com
USA: 1-800-888-8458
Europe: +31 (0)33-45 45 600
China: 400-120-3051
Japan: japansupport@ergotron.com
© 2021 Ergotron, Inc. All rights reserved.
While Ergotron, Inc. makes every effort to provide accurate and complete
information on the installation and use of its products, it will not be held
liable for any editorial errors or omissions (including those made in the
process of translation from English to another language), or for incidental,
special or consequential damages of any nature resulting from furnishing this
instruction and performance of equipment in connection with this instruction.
Ergotron, Inc. reserves the right to make changes in the product design and/or
product documentation without notification to its users. For the most current
product information, or to know if this document is available in languages
other than those herein, please contact Ergotron. No part of this publication
may be reproduced, stored in a retrieval system, or transmitted in any form or
by any means, electronic, mechanical, photocopying, recording or otherwise
without the prior written consent of Ergotron, Inc.,1181 Trapp Road, Eagan,
Minnesota, 55121, USA Patents Pending and Patented U.S. & Foreign. Ergotron is
a registered trademark of Ergotron, Inc.
888-45-418-W-00 rev. D * 10/22
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>