Wimberley AP-607 Replacement Foot for Canon Instruction Manual
- May 16, 2024
- Wimberley
Table of Contents
AP-607
Quick-release Replacement Foot for Canon:
100-500 RF f/4.5-7.1 IS
Weight: 1.95 oz
Product Dimensions (L x W x H): 4.0” x 1.5” x 0.4”
Materials: Anodized 6061 Aluminum, Stainless Steel
Package Contents:
- Arca-Swiss Style QR Plate: AP-607 Replacement Foot (Qty 1)
- Mounting Screw: 1/4-20 x 7/16”L Flat Head Socket Cap Screw (Qty 1)
- Safety Stop Screws: M3 x 3mm Socket Head Cap Screw (Qty 2)
- Hex Key: 5/32 (Qty 1)
- Hex Key: 2.5mm (Qty 1)
Made in USA
Wimberley, Inc.
1750 Broadway St
Charlottesville, VA
22902 USA
Phone: 1-434-529-8385
Toll Free: 1-888-665-2746 (USA &
Canada)
www.tripodhead.com info@tripodhead.com
10 Year Warranty – See www.tripodhead.com/warranty.cfm for complete details
Figure 1
About the AP-607
The AP-607 Replacement Foot fits the 100-500 RF f/4.5 Canon lenses and serves three main purposes:
- Added Stiffness over the factory tripod mounting foot connected to a lens plate, reducing flex and vibration.
- Functions as the Arca-Swiss style quick-release plate for your lens.
- Creates a more ideal geometry for using your lens on the Wimberley Sidemount Head and Sidekick, allowing the lens to balance optimally.
Wimberley lens plates are compatible with Arca-Swiss style quick-release clamps such as those made by Wimberley, Kirk Enterprises, Really Right Stuff, Arca-Swiss, Markins, and others.
Installation Instructions
1. Attach the AP-607 plate to the lens using the enclosed 1/4-20 screw
(Fig. 1).
2. Drive the screw in until you first meet resistance, then turn it
about 30° farther to establish appropriate, but not excessive, torque. Do
not over tighten; it is possible to shear the head off the fastener with the
hex key included.
4. Install safety stop screws as shown on page 2 (Fig. 3). Safety stop
screws are not required, however they keep your lens and camera secure when
using a compatible QR clamp.
Using Flash Brackets
Wimberley replacement feet have a double dovetail cross-section. The upper dovetail allows you to attach Wimberley Flash Brackets as well as other 3rd party quick-release style brackets.
Using the AP-607 without using a quick-release
The 3/8 and 1/4 inch holes in the middle section of the plate can be used to
attach the foot directly to the threaded stud of a monopod or other lens
support equipment, without needing a quick-release clamp.
Using the Optional Safety-Stop Screws
Your Wimberley foot comes with two safety stop screws and a matching 2.5mm hex key. Two of these screws are intended to be screwed into the small bottom threaded holes in the front and back of the foot (Fig. 3) to serve as stops that prevent the foot from accidentally sliding out of the quick-release clamp. If you opt to use both stops, you must open the jaws of the quick- release clamp wide enough to load your lens from the top (instead of sliding it in).
Top Load
(Required with Safety Stop screws)
Top Loading is less convenient, but you can be certain that your lens will not slide out of the clamp.
Safety Stop Channels We recommend using clamps with safety stop channels. These channels allow a full range of forward and backward motion but will not let the plate slip out if the clamp is inadvertently loosened.
3rd Party Clamp Warning: Our safety stop screws work with most 3rd party quick-release clamps, but clamps that do not have channels and are too wide to be straddled by the safety stop screws will not work.
Your clamp must have safety stop channels
1. Safety Stop Channels
OR
be short enough to allow the foot to straddle the clamp
Arca-Swiss Z1
The safety-stop security feature of this foot does not work when used with an
Arca-Swiss “double-decker” quick-release clamp.
If this foot safety feature is important to you, we recommend replacing the clamp with a Wimberley C-12 QR Clamp.
Clamps without safety stop channels (or those without adequate clearance) will insecurely clamp the foot at an angle
Thank you for your interest in Wimberley products. If you have any questions or comments please feel free to contact us.
Wimberley, Inc. ©2023, All Rights Reserved Rev.
230331