BRAUN 5197CC Series Clean and Charge Station User Manual
- June 14, 2024
- Braun
Table of Contents
- 5197CC Series Clean and Charge Station
- Shaver
- First use and charging
- Using the shaver
- Manual cleaning of the shaver
- Clean&Charge Station (C&C) (not with all models)
- Installing the C&C
- Using the C&C
- Charging the shaver in the C&C
- Removing the shaver from the C&C
- Cleaning cartridge / Replacement
- Accessories
- Environmental notice
- Trouble-Shooting
- Documents / Resources
Series 5
User Manual 5197cc
5195cc
5190cc
5160s
5147s
5145s
5140s
wet &dry
Type 5769
www.braun.com
5197CC Series Clean and Charge Station
Our products are designed to meet the
highest standards of quality, functionality and design. Thank you for your
trust in Braun’s quality and we hope you enjoy your new Braun product.
Read these instructions completely, they contain safety information. Keep them
for future reference.
WARNING
Your appliance is provided with a special cord set, which has an integrated
Safety Extra Low Voltage power supply. Do not exchange or tamper with any part
of it, otherwise there is risk of an electric shock. Only use the special cord
set provided with your appliance.
If the appliance is marked , you can use it with any Braun power supply coded
492-XXXX.
This appliance is suitable for cleaning under running water and use in a
bathtub or shower.
For safety reasons it can only be operated cordless.
Detach the shaver from the power supply before using it with water.
Do not shave with a damaged foil or cord.
Do not open the appliance!
The built-in rechargeable batteries can only be replaced by an authorized
Braun Service center.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision or instruction concerning
the safe use of the appliance and understand the hazards involved.
Children shall not play with the appliance. Cleaning and user maintenance
shall not be made by children unless they are supervised.
Clean &Charge Station
To prevent the cleaning fluid from leaking, ensure that the Clean&Charge
Station is placed on a flat surface. When a cleaning cartridge is installed,
do not tip, move suddenly or transport the station in any way as cleaning
fluid might spill out of the cartridge.
Do not place the station inside a mirror cabinet, nor place it on a polished
or lacquered surface.
The cleaning cartridge contains a highly flammable liquid so keep it away from
sources of ignition. Do not expose to direct sunlight and cigarette smoking
nor store it over a radiator.
Do not refill the cartridge and use only original Braun refill cartridges.
Shaver
1 Foil & Cutter cassette
2 Cassette release button
3 MultiHeadLock switch
4 On/off switch
5 Shaver display
5 a Lock symbol (travel lock)
5 b Charging segments
5 c Cleaning indicator
5 d Battery symbol
6 Long hair trimmer
7 Shaver-to-station contacts
8 Release button for long hair trimmer
9 Shaver power socket
10 a Special cord set (design can differ)
10 b Charging stand
11 Protection cap
12 Travel case*
- not with all models
First use and charging
Connect the shaver to an electrical outlet by snapping the special cord set
(10a) into the shaver power socket (9) / the charging stand (10b) or for cc
models via the Clean&Charge Station (see Chapter «Clean&Charge Station»).
Basic operating information
- A full charge provides up to 50 minutes of cordless shaving time. This may vary according to your beard growth and environmental temperature.
- Recommended ambient temperature for charging is 5 °C to 35 °C. The battery may not charge properly or at all under extreme low or high temperatures.
- Recommended ambient temperature for storage and shaving is 15 °C to 35 °C.
- Do not expose the appliance to temperatures higher than 50 °C for extended periods of time.
- When the shaver is connected to an electrical outlet, it may take some minutes until the display illuminates.
Charging / low charge
The charge status is shown in the shaver display (5).
- During charging the respective charging segment (5b) will blink.
- When the shaver is fully charged and connected to an electrical outlet, all 3 charging segments will light up for a few seconds. Then the display turns off.
- The battery symbol (5d) will flash red, when the battery is running low. You should be able to finish your shave. With switching off the shaver a beep sound reminds of the low charge status.
Using the shaver
Press the on/off switch (4) to operate the shaver.
Tips for a perfect dry shave
For best results, Braun recommends you to follow 3 simple steps:
- Always shave before washing your face.
- At all times, hold the shaver at the right angle (90°) to your skin.
- Stretch your skin and shave against the direction of your beard growth.
MultiHeadLock switch (head lock)
-
To shave hard-to-reach areas (e.g. under the nose) slide the MultiHeadLock switch (3) down to lock the shaver head.
-
The shaver head can be locked in five positions. To change position, move the shaver head with your thumb and forefinger back or forth. It will automatically click into the next position.
-
For automatic cleaning in the Clean&Charge Station the head lock should be released.
Long hair trimmer
To trim sideburns, moustache or beard press the release button (8) and slide the long hair trimmer (6) upwards.
Travel lock -
The lock symbol (5a) lights up in the display when the shaver has been locked to avoid unintended starting of the motor (e.g. for storing it in a suitcase).
-
Activation: By pressing the on/off switch (4) for 3 seconds the shaver is locked. This is confirmed by a beep sound and the lock symbol in the display. Afterwards the display turns off.
-
Deactivation: By pressing the on/off switch for 3 seconds again the shaver is unlocked.
Manual cleaning of the shaver
Cleaning under running water
- Switch on the shaver (cordless) and rinse the shaver head under hot running water until all residues have been removed. You may use liquid soap without abrasive substances. Rinse off all foam and let the shaver run for a few more seconds.
- Next, switch off the shaver, press the release button (2) to remove the Foil & Cutter cassette (1) and let it dry.
- If you regularly clean the shaver under water, then once a week apply a drop of light machine oil on top of the Foil & Cutter cassette.
The shaver should be cleaned after each foam usage.
Cleaning with a brush
- Switch off the shaver. Remove the Foil & Cutter cassette (1) and tap it out on a flat surface. Using the brush, clean the inner area of the pivoting head. Do not clean the cassette with the brush as this may damage it!
Clean&Charge Station (C&C) (not with all models)
The Clean&Charge Station has been developed for cleaning, charging,
lubricating, drying and storing your Braun shaver.
13 Station power socket
14 Lift button for cartridge exchange
15 Station-to-shaver contacts
16 Clean&Charge Station display
16 a Level indicator
16 b Status light
16 c Cleaning program indicators
17 Start button
18 Cleaning cartridge
Installing the C&C
- Remove the protection foil from the C&C display.
- Press the lift button (14) at the rear side of the C&C to lift up the housing.
- Hold the cleaning cartridge (18) down on a flat, stable surface (e.g. table).
- Carefully remove the lid from the cartridge.
- Slide the cartridge from the rear side into the base of the station until it snaps into place.
- Slowly close the housing by pushing it down until it locks.
- Using the special cord set (10a), connect the station power socket (13) to an electrical outlet.
Using the C&C
Important: The shaver needs to be dry and free from any foam or soap residue!
Insert the shaver in the C&C upside down, with the front showing and released
head lock (3).
The contacts (7) on the back of the shaver need to align with the contacts
(15) in the C&C. Push the shaver in the correct position. A beep sound
confirms that the shaver sits properly in the C&C.
The C&C analyzes the cleanliness. It is shown by the cleaning program
indicators (16c) in the C&C display (16).
Charging the shaver in the C&C
Charging will start automatically when the shaver has been placed in properly.
Cleaning the shaver in the C &C
When the cleaning indicator (5c) lights up in the shaver display, insert the
shaver into the C&C, as described above.
Cleaning programs
short economical cleaning
normal level of cleaning
high intensive cleaning
Start automatic cleaning
Start the cleaning process by pressing the start button (17). If status light
(16b) does not shine (C&C switches to stand-by after ca. 10 minutes), press
start button twice.
Otherwise cleaning will not start. For best shaving results, we recommend
cleaning after each shave.
Each cleaning program consists of several cycles, where cleaning fluid is
flushed through the shaver head. Depending on your Clean&Charge Station model
and/or program selected, the cleaning time takes up to 3 minutes. During this
time the status light blinks. Leave the shaver in the station for drying. It
takes several hours until remaining moisture evaporates depending on the
climatic conditions.
After completing the cleaning and charging procedure, all indicators turn off.
Removing the shaver from the C&C
Hold the C&C with one hand and tilt the shaver slightly to the front to release it.
Cleaning cartridge / Replacement
When the level indicator (16a) lights up permanently red, the remaining fluid
in the cartridge is sufficient for about 3 more cycles. When the level
indicator blinks red, the cartridge needs to be replaced.
After having pressed the lift button (14) to open the housing, wait for a few
seconds before removing the used cartridge to avoid any dripping. Before
discarding the used cartridge, make sure to close the openings using the lid
of the new cartridge, since the used cartridge will contain contaminated
cleaning solution.
The cleaning cartridge contains ethanol or isopropanol (specification see
cartridge), which once opened will naturally evaporate slowly. Each cartridge,
if not used daily, should be replaced after approximately 8 weeks. The
cleaning cartridge also contains lubricants for the shaving system, which may
leave residual marks on the outer foil frame and the cleaning chamber of the
C&C. These marks can be removed easily by wiping gently with a damp cloth.
Accessories
Braun recommends changing your shaver’s Foil & Cutter cassette every 18 months
to maintain your shaver’s maximum performance.
Available at your dealer or Braun Service Centres:
- Foil & Cutter cassette: 52S/52B
- Cleaning Cartridge: CCR
- Braun Shaver cleaner spray
Environmental notice
**** Product contains batteries and/or recyclable electric waste. For
environment protection do not dispose of in household waste, but for recycling
take to electric waste collection points provided in your country.
The cleaning cartridge can be disposed of with regular household waste.
Subject to change without notice.
For electric specifications, see printing on the special cord set.
Trouble-Shooting
Problem | Possible reason | Remedy |
---|
SHAVER
Shaver does not charge completely and
keeps blinking.| Ambient temperature is out of valid range.| Recommended
ambient temperature for charging is 5 °C to 35 °C.
Charging does not start when connected to
power socket.| 1. Sometimes charging could start delayed (e.g. after long
storage).
2. Ambient temperature is out of valid range.
3. Special cord set is not plugged in properly.| 1. Wait a few minutes, if
charging will start automatically.
2. Recommended ambient temperature for charging is 5 °C to 35 °C.
3. Special cord set needs to snap into place.
Unpleasant smell from the shaver head.| 1. Shaver head is cleaned with water.
2. Cleaning cartridge is in use for more than 8 weeks.| 1. When cleaning the
shaver head with water only use hot water and from time to time some liquid
soap (without abrasive substances). Remove Foil & Cutter cassette to let it
dry.
2. Change cleaning cartridge at least every 8 weeks.
Battery performance dropped significantly.| 1. Foil and cutter are worn which
requires
more power for each shave.
2. Shaver head is regularly cleaned with water but not lubricated.| 1. Renew
Foil & Cutter cassette.
2. If the shaver is regularly cleaned with water, apply a drop of light
machine oil on top of the foil once a week for lubrication.
Shaving performance dropped significantly.| 1. Foil and cutter are worn.
2. Shaving system is clogged.| 1. Renew Foil & Cutter cassette.
2. Soak the Foil & Cutter cassette into hot water with a drop of dish liquid.
Afterwards rinse it properly and tap it out. Once dry apply a drop of light
machine oil on the foil.
Shaver head is damp.| 1. Drying time after automatic cleaning was too short.
2. Drain of the Clean&Charge Station is clogged.| 1. Clean directly after
shaving to allow enough time for drying.
2. Clean the drain with a wooden toothpick.
CLEAN&CHARGE STATION
Cleaning does not start when pressing the
start button.| 1. Shaver is not placed properly in the
Clean&Charge Station.
2. Cleaning cartridge contains not enough cleaning fluid (display blinks
red).| 1. Insert shaver into the Clean&Charge Station and push it to the rear
side of the station (contacts of the shaver need to align with contacts in the
station).
2. Insert new cleaning cartridge.
Press start button again.
Increased consumption of cleaning fluid.| Drain of the Clean& Charge station
is clogged.| – Clean the drain with a wooden toothpick.
– Regularly wipe the tub clean.
Guarantee
We grant a 2-year guarantee on the product commencing on the date of purchase.
Within the guarantee period we will eliminate any defects in the appliance
resulting from faults in materials or workmanship, free of charge either by
repairing or replacing the complete appliance at our discretion.
Depending on availability replacement might result in a different color or an
equivalent model.
This guarantee extends to every country where this appliance is supplied by
Braun or its appointed distributor.
This guarantee does not cover: damage due to improper use, normal wear and
tear (e.g. shaver foil or cutter block) as well as defects that have a
negligible effect on the value or operation of the appliance. The guarantee
becomes void if repairs are undertaken by unauthorised persons and if original
Braun parts are not used.Please note down the suggested
replacement date (in 18 months
from now) below replacement part
reference number.
52S/52B
To obtain service within the guarantee period, hand in or send the complete
appliance with your sales receipt to an authorised Braun Customer Service
Centre (address information available online at
www.service.braun.com).
For UK only:
This guarantee in no way affects your rights under statutory law.
For Australia & New Zealand only:
In Australia, our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and for compensation for any other reasonably foreseeable loss
or damage.
You are also entitled to have the goods repaired or replaced if the goods fail
to be of acceptable quality and the failure does not amount to a major
failure.
The benefi ts given by this warranty are in addition to other rights and
remedies of the consumer law.
For warranty claims please contact:
Procter & Gamble Australia Pty Ltd
Level 4, 1 Innovation Road
Macquarie Park, NSW 2113
Telephone (AU): 1 800 641 820
Telephone (NZ): 0 800 108 909
Email (AU and NZ): Visit link
https://pgconsumersupport.secure.force.com/ContactUs/emailus
Our Warranty
This appliance is also covered by a 24 Month Replacement Warranty commencing
on the date of purchase (Our Warranty).
Our Warranty applies in all States and Territories of Australia and in New
Zealand and is in addition to any mandatory statutory obligations imposed on
Procter & Gamble Australia Pty. Ltd., its distributors and its manufacturer.
Our Warranty does not purport to exclude, restrict or modify any such
mandatory statutory obligations.
Our Warranty only covers defects in the appliance resulting from faults in
workmanship or materials. Therefore, if your appliance becomes faulty as a
result of faults in workmanship or materials, it will be exchanged by your
retailer, on presentation of proof of purchase.
Our Warranty only applies to domestic or household use of this appliance and
the warranty will only apply if the correct operating instructions included
with this product have been followed. For any appliance replaced under this
warranty, Our Warranty ends on the expiry of the warranty period that applied
to the original appliance.
Our Warranty does not cover:
A. Damage arising from improper use or operation on incorrect voltages.
B. Breakages to shaver foils, glass jars, etc.
C. Normal wear due to moving parts.
D. Repairs undertaken by unauthorised service personnel or use of non genuine
parts.
E. Appliances that are outside the warranty period or are not faulty.
This appliance is not intended for use by young children or infi rm persons
without supervision. Young children should be supervised to ensure that they
do not play with the appliance.
If the appliance is powered by a cord extension set or electrical portable
outlet device these should be positioned so they are not subject to splashing
or ingress of moisture.
To the extent permitted by the laws of the Commonwealth of Australia and New
Zealand and applicable laws of a State or Territory of Australia, and without
aff ecting any mandatory statutory obligations imposed by law, Our Warranty is
given in exchange for any other rights you may have against Procter & Gamble
Australia Pty. Ltd. or its distributors or manufacturer, whether at law, in
tort (including negligence), in equity or under statute.
Please retain proof of purchase of this appliance. If you have any questions
in relation to Our Warranty, please call our Consumer Service line (see below
for numbers).
If you intend to make a claim please telephone our Customer Service line on
the numbers set out below to obtain information about your claim and any costs
associated with claiming under Our Warranty. You will bear the cost of
returning your product to us.
Repairs and service
If you are sending your appliance for repair under Our Warranty, please pack
the appliance adequately and send it to your nearest Service Agent, at your
expense. Should your Braun product require service, please call (free call)
for Australia 1800 641 820 or New Zealand 0800 108 909 to be referred to the
Authorized Braun Service Center closest to you or visit
www.service.braun.com. ****
Please note down the suggested replacement date (in 18 months from now) below
replacement part reference number.
52S/52B
Braun GmbH
Frankfurter Straße 145
61476 Kronberg/Germany
www.braun.com
www.service.braun.com 90907760/X- 1 9
Documents / Resources
|
BRAUN 5197CC Series Clean and Charge
Station
[pdf] User Manual
5197cc, 5195cc, 5190cc, 5160s, 5147s, 5145s, 5140s, 5197CC Series Clean and
Charge Station, 5197CC Series, Clean and Charge Station, Charge Station,
Station
---|---
References
- Braun Electric Shavers and Razors | Braun
- Braun Service
- pgconsumersupport.secure.force.com/ContactUs/emailus
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>