PHALANX PHG0240-US Heat Gun Instruction Manual

June 14, 2024
PHALANX

PHALANX-logo

PHALANX PHG0240-US Heat Gun

PHALANX-PHG0240-US-Heat-Gun-fig-1

Safety Information

WARNING: When using electric tools, basic safety precautions should always be followed to reduce risk of fire, electric shock, and personal injury, including the following.
READ ALL INSTRUCTIONS TO REDUCE RISK OF INJURY:

  • Before any use, be sure everyone using this tool reads and understands all safety instructions and other information contained in this manual.

  • Save these instructions and review frequently prior to use and in instructing others.

  • General Safety Warnings and Instructions for All Tools

  • KEEP WORK AREA CLEAN. Cluttered areas and benches inviteinjuries.

  • CONSIDER WORK AREA ENVIRONMENT. Don’t expose power tools to rain. Don’t use power tools in damp or wet locations. Keep work area well lit. Do not use in presence of flammable liquids or gases. Motors in these tools normally spark, and the sparks may ignite the fumes.

  • GUARD AGAINST ELECTRIC SHOCK. Prevent body contact with grounded surfaces. For example; pipes, radiators, ranges, refrigerator enclosures. Use extreme caution when drilling, driving, or cutting into walls, floors, ceilings or other areas or wherever live electrical wires may be contacted, do not touch any metal parts of the tool. Hold the tools only by the plastic handle to prevent electric shock.

  • KEEP CHILDREN AWAY. Do not let children and visitors contact tool or extension cord. All children and visitors should be kept away from work area.

  • STORE IDLE TOOLS. When not in use, tools should be stored in dry, and high or locked up place-out of reach of children.

  • DON’T FORCE TOOL. It will do the job better and safer at the rate for which it was intended.

  • USE RIGHT TOOL. Don’t force small tool or attachment to do the job of a heavy-duty tool. Don’t use tool for purposes not intended.

  • DRESS PROPERLY. Do not wear loose clothing or jewelry. They can be caught in moving parts. Heavy duty gloves to protect hands and non-skid footwear are recommended when working outdoors. Wear protective hair covering to contain long hair.

  • USE SAFETY GLASSES AND OTHER SAFETY EQUIPMENT. Use safety goggles or safety glasses with side shields, complying with applicable safety standards and, whenneeded, a face shield. Also use face or dust mask if cutting operation is dusty. This applies to all persons in the work area. Also use a hard hat, hearing protection, gloves, safety shoes and dust collection systems when specified or required.

  • DON’T ABUSE CORD. Never carry tool by cord or yank it to disconnect from receptacle. cord from heat, oil, and sharp edges.

  • SECURE WORK. Use clamps or a vise to hold work. It’s safer than using your hand audit frees both hands to operate tool.

  • DON’T OVERREACH. Keep proper footing and balance at all times.

  • MAINTAIN TOOLS WITH CARE. Keep tools sharp and clean for better and safer performance. Follow instructions for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have repaired by authorized service facility. Inspect extension cords periodically and replace if damaged. Keep handles dry, clean, and free from oil and grease.

  • DISCONNECT TOOLS. Unplug the tool when not in use, when moving tool from place to place, before servicing, and when changing accessories (such as blades, bits, cutters) or making adjustments.

  • REMOVE ADJUSTING KEYS AND WRENCHES. Form habit of checking to see those keys and adjusting wrenches are removed from tool before turning it on.

  • AVOID UNINTENTIONAL STARTING. Don’t carry tool with finger on switch. Be sure switch is off when plugging in.

  • OUTDOOR USE EXTENSION CORDS. When tool is used outdoors, use only extension
    cords intended for use outdoors and so marked.

  • STAY ALERT. Watch what you are doing. Use common sense. Do not operate tool when you are tired or otherwise impaired.

  • CHECK DAMAGED PARTS. Before further use of the tool, a guard or other part that is damaged should be carefully checked to determine that it will operate properly and perform its intended function. Check for aligrnnent of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center. Do not use tool if switch does not turn it on and off.

  • REP AIRS AND SERVICE. Repairs, maintenance and any adjustments not specified in this
    manual should be performed by authorized service centers or other qualified service organizations, always using identical replacement parts.

  • USE OF ACCESSORIES AND ATTACHMENTS.

  • The use of any accessory or attachment not recommended for use with the tool could be hazardous. Note: Refer to the accessory section of this manual for further details.

Additional Safety Instructions
SAFETY GUIDELINES – DEFINITIONS

  • It is important for you to read and understand this manual.
  • The information it contains relates to protecting YOUR SAFETY and PREVENTING
  • PROBLEMS. The symbols below are used to help you recognize this information.
  • DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
  • WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
  • CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
  • CAUTION: Used without the safety alert symbol indicates a potentially hazardous situation which, if not avoided, may result in property damage.

IMPORTANT SAFETY INSTRUCTIONS FOR HEAT GUNS

  1. Remember that hidden areas such as those behind walls, ceilings, floors, soffit boards and other panels may contain flammable materials that could be accidentally ignited when stripping paint from the panel. Such a fire would not be readily apparent, and could cause considerable damage and danger of injury. These heat guns are capable of producing temperatures in excess of 1202 °F ( 650°C).
  2. Do not use this tool as a hair dryer.
  3. Allow the tool to cool before storing. Do not lay the heat gun on flanunable surfaces when operating the gun or immediately after shutting it off. Always set the gun on a flat level surface so that the nozzle tip is pointed upward.
  4. Always use good quality scrapers and stripping knives.
  5. Never obstruct the air intake or nozzle outlet.
  6. Be sure to direct the hot air blast in a safe direction; away from other people or flanunable objects.
  7. Keep fingers away from metal nozzle; it becomes very hot.
  8. Don’t touch the nozzle to any surface while running or shortly after running.
  9. Avoid poking anything down inside the nozzle.
  10. Clean dry paint from the nozzle after use; it could ignite.
  11. Clean your scraper blade frequently during use; it could ignite.
  12. Do not use the heat gun in combination with chemical strippers.
  13. Do not use accessory nozzles as scrapers.
  14. Keep nozzle away from cord.
  15. Do not use to cook or warm food.
  16. Be constantly aware that this tool can ignite flammable materials, and soften or melt others. Regardless of the task you are performing, shield or keep away from these materials that are close to the work area.

™PORTANT NOTICE:

  • In order for this tool to be an effective paint stripper, it must produce extremely high temperatures. As a consequence, the stripper is capable of igniting paper, wood, paint and varnish residue and similar materials.
  • As you become more familiar with the tool and develop the proper technique, the danger of accidental ignition will be greatly reduced. In establishing the proper technique, the best thing to do is practice! Work on simple stripping projects, preferably outdoors, until you get a “feel” for how to use your stripper safely and effectively.
  • As you practice, observe the following procedures for safety:
    1. Always be sure the tool is turned off and disconnected from power supply when unattended.
    2. Clean the scraper blade often during use. Built up residue on the blade is highly flanunable.
    3. Experiment to find the optimum distance from the tool’s nozzle to the surface being stripped. This distance (usually 1-2 inches) (2 5-50 mm) will vary depending on the material being removed.
    4. Keep the heat gun moving ahead of the scraper blade at all the time.
    5. As you work, clean up loose pieces of paint as they accumulate around the work area.
    6. When working indoors, keep away from curtains, papers, upholstery and similar flammable materials.
    7. Above all, remember that this is a serious power tool that is capable of producing excellent results when used properly. Practice on simple projects until you feel comfortable with your stripper. Only then will you have mastered the proper technique.
      WARNING: Extreme care should be taken when stripping paint. The peelings, residue and vapors of paint may contain lead, which is poisonous. Any pre-1977 paint may contain lead and paint applied to homes prior to 1950 is likely to contain lead. Once deposited on surfaces, hand to mouth contact can result in the ingestion of lead. Exposures to even low levels of lead can cause irreversible brain and nervous system damage; young and unborn children are particularly vulnerable. Before beginning any paint removal process, you should determine whether the paint you are removing contains lead.
      This can be done by your local health department or by a professional who uses a paint analyzer to check the lead content of the paint to be removed.

Lead based paint should only be removed by a professional and should not be removed using a heat gun.
Persons removing paint should always follow these guidelines:

  1. Move the work piece outdoors. If this is not possible, keep the work area well ventilated. Open the windows and put an exhaust fan in one of them. Be sure the fan is moving the air from inside to outside.
  2. Remove or cover any carpets, rugs, furniture, cooking utensils, and air ducts.
  3. Place drop cloths in the work area to catch any paint chips or peelings. Wear protective clothing such as extra work shirts, overalls and hats.
  4. Work in one room at a time. Furnishings should be removed or placed in the center of the room and covered. Work areas should be sealed off from the rest of the dwelling by sealing doorways with drop cloths.
  5. Children, pregnant women or potentially pregnant women and nursing mothers should not be present in the work area until the work is done and all clean-up is complete.
  6. Wear a dust respirator mask or a dual filter (dust and fume) respirator mask which has been approved by the Occupational Safety and Health Administration (OSHA), the National Institute of Safety and Health (NIOSH), or the United States Bureau of Mines. These masks and replaceable filters are readily available at major hardware stores. Be sure the mask fits. Beards and facial hair may keep masks from sealing properly. Change filters often. Disposable paper masks are not adequate.
  7. Use caution when operating the heat gun. Keep the heat gun moving as excessive heat will generate fumes which can be inhaled by the operator.
  8. Keep food and drink out of the work area. Wash hands, arms and face and rinse mouth before eating or drinking. Do not smoke or chew gum or tobacco in the work area.
  9. Clean up all removed paint and dust by wet mopping the floors. Use a wet cloth to clean all walls, sills and any other surface where paint or dust is clinging. Do not sweep, dry dust or vacuum. Use a high phosphate detergent or trisodium phosphate (TSP) to wash and mop areas.
  10. At the end of each work session put the paint chips and debris in a double plastic bag, close it with tape or twist ties, and dispose of properly.
  11. Remove protective clothing and work shoes in the work area to avoid carrying dust into the rest of the dwelling. Wash work clothes separately. Wipe shoes off with a wet rag that is then washed with the work clothes. Wash hair and body thoroughly with soap and water.

The label on your tool may include the following symbols.

PHALANX-PHG0240-US-Heat-Gun-fig-2

WARNING: Some dust created by power sanding, sawing, grinding, drilling, and other construction activities contains chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

  • lead from lead-based paints,
  • crystalline silica from bricks and cement and other masonry products, and arsenic and chromium from chemically-treated lumber.
    Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.

Allowing dust to get into your mouth, eyes, or lay on the skin may promote absorption of harmful chemicals.

  • WARNING: Use of this tool can generate and/or disperse dust, which may cause serious and permanent respiratory or other injury. Always use NIOSH/OSHA approved respiratory protection appropriate for the dust exposure. Direct particles away from face and body.
  • WARNING: ALWAYS use safety glasses. Everyday eye glasses are NOT safety glasses. Also use face or dust mask if cutting operation is dusty. ALWAYS WEAR CERTIFIED SAFETY EQUIPMENT:
    • ANSI Z87.I eye protection (CAN/CSA Z94.3)
    • ANSI Sl2.6 (S3.19) hearing protection
    • NIOSH/OSHA/MSHA respiratory protection

Important Electrical Information

  • Use only an extension cord that will accept the plug on the product. Make sure your extension cord is in good condition.
  • When using an extension cord, be sure to use one heavy enough to carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. A SIT type cord is required. Cord shall be 14 A WG minimum for general indoor use.
  • This appliance has a polarized plug ( one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not modify the plug in any way.
  • When servicing, only use identical service parts. Contact Phalanx for a replacement cord set. For proper size cords see chart below
  • This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
  • Children should be supervised to ensure that they do not play with the appliance.
  • If the SUPPLY CORD is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified person in order to avoid a hazard.
  • A fire may result if the appliance is not used with care, therefore
    • be careful when using the appliance in places where there are combustible materials;
    • do not apply to the same place for a long time;
    • do not use in presence of an explosive atmosphere;
    • be aware that heat may be conducted to combustible materials that are out of sight;
    • place the appliance on its stand after use and allow it to cool down before storage;
    • do not leave the appliance unattended when it is switched on.

PHALANX-PHG0240-US-Heat-Gun-fig-3
Be sure your power supply agrees with the nameplate marking. 120 Volts AC only means your tool will operate on standard 60 Hz household power. Do not operate AC tools on DC. Lower voltage will cause loss of power of vent motor and can result in over-heating.

Operation Instruction

General Description
This heat gun is a quality power tool. Like any power tool, it can be dangerous when misused. Read the following instructions carefully and follow all safety precautions. It is the responsibility of the owner to use the heat gun properly. Only adults should use a heat gun.

Component Description

PHALANX-PHG0240-US-Heat-Gun-fig-5

  1. Nozzle
  2. Heat Shield
  3. Hanging Hook
  4. Air Vents
  5. Rear Stabilizer Fins (Stand)
  6. Temperature Regulator
  7. Two Speed Switch (0=OFF,l =LOW,2=HIGH)
  8. Power cord ( 6.6 ft UL approved wire)Save the Instruction

Hands-Free Operation
The heat gun has an integrated stand for bench top applications and cool down mode as shown below.

Heat Gun Specification

  • Voltage 120V
  • Frequency 60Hz
  • Power
1. 650 W
2. 1500W
  • Speed Setting
1. Low
2. High
  • Air Flow
1. 300L/M
2. 500L/M
  • Temperature
1. 50-400°C (l22~752°F)
2. 90~650°C (194~ 1202°F)  

7- grade adjustable each setting

Startup
The position of the switch controls both the ventilation fan speed and the heat gun output power of the gun.

  • To turn the tool on in low speed, low heat, slide the switch marked “l “.
  • To turn the tool on in high speed, high heat, slide the switch marked “2”.
  • To turn the tool off, slide the switch to the position marked “0”. Always disconnect heat gun from the power supply at completion of task.

PHALANX-PHG0240-US-Heat-Gun-fig-7

Nozzles & Accessories Introduction
The following accessories may come with the heat gun or may purchased separately from Phalanx store.
IMPORTANT: Always use gloves when handling the heat gun

PHALANX-PHG0240-US-Heat-Gun-fig-8

To attach a nozzle to the gun

  1. Set the heat gun upright on a level surface until the tip is cool.
  2. Firmly push to set the item

To remove a nozzle:

  1. Set the heat gun upright on a level surface until the tip is cool.
  2. Pull the item off the tip

Heating Guidelines and Applications
The heat gun is one of the most versatile tools you can own. It can be used for a great variety of projects, from DIY to small art & craft jobs, roast bacon and coffee beans.

PHALANX-PHG0240-US-Heat-Gun-fig-9 PHALANX-
PHG0240-US-Heat-Gun-fig-10

See above section of Nozzles & Accessories Introduction for details.

  • Note: Always set the heat gun upright after it is turned off, either for a short break or for storage. Avoid laying the unit on the side after shutdown. The heat will remain in the unit and cooling will take longer. Store the unit only after the nozzle is cool. Unplug the unit before storing to prevent accidental startup.
  • IMPORTANT:
    • Always protect glass when working near windows.
    • Do not touch nozzle or the scraper blade when working. These become extremely hot and will cause severe burns. Wear gloves to protect hands from hot scrapings.

Stripping Paint
IMPORTANT: Read the general operating and safety information sections of this owner’s manual before using the heat gun.

  • The heat gun heats up the surface and causes the paint to soften, at which time it can be scraped off easily without damaging the surface. Some paints may soften even though they do not blister; some may become rubbery, and some may require higher heat. When working with several layers of paint, it speeds up the scraping process to heat the surface thoroughly, all the way to the wood. Then all the layers can be scraped at one time.
  • A soft wire brush may be the best tool to use for very intricate surfaces. Mineral paints and finishes, such as cement paint and porcelain, do not soften with heat, so using a heating tool will not work for paint removal.

The best method of paint removal
Move the gun slowly and steadily forward at an angle to the surface, pointing the nozzle in the direction of motion. This allows you to scrape safely outside the hot air stream and keeps the scraper and the scraped surface cooler.

  • A – Warm air preheats the surface.

  • B – Paint is softened by hot air.

  • A+ B – Deep penetration of heat over total area.

  • C – Paint can be easily scraped off as soon as it is softened and the gun is moved forward.

  • D – Stripped surface allowed to cool.

    • Note:
    • Do not use the heat gun on surfaces that can be damaged by heat, such as vinyl -coated paneling, siding or window frames.
    • When removing paint from window frames, the heat gun will soften the putty. Be careful not to gouge the putty with the scraper. The putty will firm up after it cools. Do not use the heat gun on insulating laminated window glass such as Thermopane. The glass edge expansion may break the edge seal. When scraping fascia, do not overheat the edges of the asphalt shingles protruding over the edge of the sheathing. Too much heat will melt the asphalt.
    • IMPORTANT:
    • The removal of paint by heat gun is safe if the above guidelines are used,but always keep either a container of water or an ABC fire extinguisher (suitable againse Class A,B and C type fires) within reach.
    • Make sure that the nozzle always points aways from you and any bystanders.
    • Make sure not to drop anything into the nozzle.

Cleaning and Maintenance

  • Keep the intake openings on the housing clean and free of obstructions.
  • Us a soft, dry brush to clean the openings periodically.
  • Use only mild soap and a damp cloth to clean the heat gun. Many household cleaners contain chemicals which could seriously damage the housing. Do not use gasoline, turpentine, lacquer or paint thinner, dry-cleaning fluids or similar products when cleaning the heat gun.
  • Never allow any liquid to get inside the tool or immerse any part of the tool into a liquid.

Storage
Allow the heat gun nozzle to cool to room temperature before placing in storage. The nozzle will turn dark over time because of the high heat. This is normal and will not affect the performance or life of the unit.
IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment ( other than those listed in this manual) should be performed by authorized service centers or other qualified service personnel, always using identical replacement parts.

Guarantee and Customer Service

  • This tool is guaranteed for 1 year from the date of purchase, if bought in store, delivered or if bought online.
  • You may only make a claim under this guarantee upon pr=tation of your sales receipt or purchase invoice. Please keep your proof of purchase in a safe place.
  • This guarantee covers product failures and malfunctions provide power tool was used for the pwpose for which it is intended and subject to installation, cleaning, care and maintenance in accordance with standard practice and with the information contained above and in the user manual. This guarantee does not cover defects and damage caused by or resulting from:
    • Normal wear and tear
    • Overload, misuse or neglect
    • Repairs attempted by anyone other than an authorized agent
    • Cosmetic damage
    • Damage caused by foreign objects, substance or accidents
    • Accidental damage or modification
    • Failure to follow manufacture’s guidelines
  • The product is designed for home usage only. If used for commercial or rental purposes. This warranty applies only for 30 days from the date of purchase.
  • Have you tried the recommendations above and are still having problems? In the United States, to contact to a customer service representative, mail our Technical Service at servjce@phaianxtoois.com We will get back to you within 24 hours.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals