PHALANX PDD2167 20V Cordless Drill Set Instruction Manual

PHALANX PDD2167 20V Cordless Drill Set

Description of Symbols

• The rating plate on your tool may show symbols.
• These represent important information about the product or instructions on its use.
• Wear hearing protection Wear breathing protection
  • Wear eye protection Wear head protection
• Wear hand protection
• Read instruction manual
• DO NOT incinerate batteries!
• Caution!
• For indoor use only!
• Class II construction
• Environmental Protection
• Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.
• Li-ion battery cells are recyclable and should not be disposed of with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice

Specification

Wood: 027 mm
Battery Pack Voltage| DC 20V
Battery Cell| Li-Ion 2.0Ah

Product Features

1. Chuck
2. Torque Selector
3. Gear Switch
4. Motor Vents
5. Forward/Reverse Switch
6. Trigger Switch
7. Soft Grip Handle
8. LED Work Light
9. Battery Release Button

• We recommend that you purchase your accessories from the same store that sold you tools.

WARNING:

• Always wear ear protection where the sound level exceeds 85dB(A) and limit the time of exposure if necessary.
• If sound levels are uncomfortable, even with ear protection, stop using the tool immediately and check the ear protection is correctly fitted and provides the correct level of sound attenuation for the level of sound produced by your tool.

WARNING:

• User exposure to tool vibration can result in loss of sense of touch, numbness, tingling, and reduced ability to grip. Long-term exposure can lead to a chronic condition. If necessary, limit the length of time exposed to vibration and use anti-vibration gloves. Do not operate the tool with hands below a normal comfortable temperature, as vibration will have a greater effect. Use the figures provided in the specification relating to vibration to calculate the duration and frequency of operating the tool. Sound and vibration levels in the specification are determined according to EN60745 or similar international standards. The figures represent the normal use of the tool in normal working conditions.
• A poorly maintained, incorrectly assembled, or misused tool may produce increased levels of noise and vibration. www.phalanxtools.com provides information on sound and vibration levels in the workplace that may be useful to domestic users who use tools for long periods.

General Safety

WARNING :

• Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury.

WARNING:

• This appliance is not intended for use by persons (including children) with reduced, physical or mental capabilities or lack of experience or knowledge unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their safety. Children must be supervised to ensure that they do not play with the appliance.
• Save all warnings and instructions for future reference
• The term “power tool” in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.

1. Work area safety

   • a ) Keep the work area clean and well-lit. Cluttered or dark areas invite accidents.
   • Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks that may ignite the dust or fumes.
   • Keep children and bystanders away while operating a power tool. Distractions can cause you t lose control.

2. Electrical safety

   • Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce the risk of electric shock.
   • b) Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
   • c) Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
   • d) Do not abuse the cord. Never use the cord for carrying, pulling, or unplugging the power tool.
   • Keep the cord away from heat, oil, sharp edges, or moving parts. Damaged or entangled cords increase the risk of electric shock.
   • When operating a power tool outdoors, use an extension cord suitable for outdoor use. The use of a cord suitable for outdoor use reduces the risk of electric shock.
   • f) If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. The use of an RCD reduces the risk of electric shock.

3. Personal safety

   • Stay alert, watch what you are doing, and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol, or medication.
   • A moment of inattention while operating power tools may result in serious personal injury.
   • b) Use personal protective equipment. Always wear eye protection. Protective equipment such as dust masks, non-skid safety shoes, hard hats, or hearing protection used for appropriate conditions will reduce personal injuries.
   • Prevent unintentional starting. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
   • Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
   • Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations
   • f) Dress properly. Do not wear loose clothing or jewelry. Keep your hair, clothing, and gloves away from moving parts. Loose clothes, jewelry, or long hair can be caught in moving parts.
   • g) If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. The use of dust collection can reduce dust-related hazards.

4. Power tool use and care

   • a) Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.

   • b) Do not use the power tool if the switch does not turn on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
     С) Disconnect the plug from the power source and/or the battery pack from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally. Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.

   • Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts, and any other condition that may affect the power tool’s operation. If damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.

   • Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.

   • Use the power tool, accessories tool bits, etc. under these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.

   • WARNING:

   • When used in Australia or New Zealand, it is recommended that this tool is ALWAYS supplied via a Residual Current Device (RCD) with a rated residual current of 30mA or less

5. Battery tool use and care

   • a) Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack
   • b) Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
   • c) When the battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
   • d) If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
   • e) Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact occurs, flush with water. If liquid contacts the eyes, seek medical help. Liquid ejected from the battery may cause irritation or burns.

6. Service

   • a) Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.

Additional Safety for Battery-Operated Drills

WARNING: : Important:

• It is imperative to follow all national safety regulations concerning installation, operation, and maintenance.
• a ) DO NOT allow anyone under the age of 18 years to use this tool, and ensure that operators are qualified and familiar with the operating and safety instructions
• b ) Battery chargers are for indoor use only. Ensure that the power supply and charger are protected against moisture at all times.
• c ) When using the drill, use safety equipment including safety glasses or shield, ear defenders, and protective clothing including safety gloves. Wear respiratory protection suitable for the work being undertaken. A minimum rating of FFP2 is recommended. If operating the tool causes discomfort in any way, stop immediately and review your method of use
• d ) Use metal and voltage detectors to locate concealed electric, water, or gas lines. Avoid touching live components or conductors
• e ) Ensure that the lighting is adequate
• f ) Ensure that the drill bit is securely fixed in the chuck. Insecure drill bits can be ejected from the machine causing a hazard
• g ) Ensure that the drill bit is not in contact with the workpiece before starting up the tool
• h ) Before drilling, check that there is sufficient clearance for the drill bit under the workpiece
• I )) DO NOT exert pressure on the tool. To do so would shorten its service life Drill bits get hot during operation, so allow to cool before handling them
• K ) NEVER use your hands to remove sawdust, chips, or waste close by the bit If you are interrupted when operating the drill, complete the process and switch off before looking up
• m ) Where possible, use clamps or a vice to hold your work
• n ) Examine the chuck regularly for signs of wear or damage. Have damaged parts repaired by a qualified service center.
• o) ALWAYS wait until the drill has com ALWAYS wait until the drill has come to a complete stop before putting it down
• p) Periodically check all nuts, bolts, and other fixings and tighten where necessary

Battery Safety

WARNING:

• Li-lon batteries, if incorrectly used, stored, or charged are a fire, burn, and explosion hazard.
• Keep the battery out of reach of children
• ONLY charge Li-lon batteries using the charger provided or designed specifically for your product ONLY use Li-lon batteries provided with a product or specifically designed to be compatible
• Allow batteries to cool for 15 minutes after charging or heavy use. Failure to follow these instructions may cause overheating or fire
• When not in use batteries should be stored at room temperature (approximately 20°C)
• Ensure that battery contacts cannot accidentally short in storage. Keep batteries clean; foreign objects or dirt may cause a short. Keep away from other metal objects, for example, paperclips, coins, keys, nails, and screws
• Under abusive conditions, liquid may be ejected from the battery. This liquid may cause skin irritation or burns. Avoid contact. If contact accidentally occurs, flush with water. If liquid contacts the eyes, seek medical help
• DO NOT open, disassemble, crush, heat above 60°C or incinerate. Do not dispose of in fire or similar

USE Phalanx

Use the battery charger correctly

• Refer to the section of this manual relating to the use of the battery charger before attempting to charge the battery.
• Do not attempt to use the charger with any batteries other than those supplied. Keep your battery charger clean; foreign objects or dirt may cause short or block air vents. Failure to follow these instructions may cause overheating or fire
• If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons to avoid a hazard

WARNING:

• DO NOT attempt to recharge non-rechargeable batteries.

Before Use

Removing a battery

• Remove the Battery from the tool by pressing the Battery Release button, then slide the Battery out of the Battery Slot.

WARNING:

• DO NOT try to remove the Battery without pressing the Battery Release button. The tool or Battery could be damaged.

Fitting a battery

• Fit a battery by sliding it onto the Battery Slot of the tool until it clicks and locks into position

Note:

• Make sure the Battery and tool are lined up correctly.
• If the Battery does not slide into the tool easily, do not force it. Instead, slide the Battery out of the tool again, check the top of the Battery and the tool battery slot are clean and undamaged and that the contacts are not bent

WARNING:

• The charger is designed for indoor use only, and MUST NOT be used in wet conditions.
• Use this charger ONLY to charge the supplied battery or additional purchased batteries that are specifically designed for this tool.
• Use this charger ONLY to charge the supplied battery or additional purchased batteries that are specifically designed for this tool.

WARNING: The charger is designed.

Charging the battery

WARNING:

• Failure to follow the correct procedure when charging batteries will result in permanent damage.

Note:

• Normal charging time is approximately 7 hr for a recently discharged 2.0Ah capacity battery. However, if the Battery has been left in a discharged state for some time, it may take additional time to charge.

Note:

• Make sure the Battery and Battery Charger are lined up correctly. If the charger plug does not insert into the Battery Charger easily, don’t force it. Instead, remove the charger plug, and check the top of the Battery and the Battery Charger slot are clean and undamaged and that the contacts are not bent.

IMPORTANT:

• When a low charge level is indicated, the tool may stop operating while in use, which is dangerous when operating a circular saw. Always ensure the battery pack has a good charge level.
• Note: about battery charging:
• The battery should be charged at ambient temperatures between 7 o and 40°C (ideally around 20°c)
• After charging, allow 15 minutes for the battery to cool before use
• Ensure that the charger is disconnected from the mains supply after use, and is stored correctly DO NOT leave batteries on charge for extended periods and NEVER store batteries on charge The Battery Charger monitors battery temperature and voltage while charging. Remove the Battery once charging is complete to maximize the charge cycles of the battery and not waste power
• Batteries can become faulty over time, individual cells in the battery can fail and the battery could short. The charger will not charge faulty batteries. Use another battery, if possible, to check the correct functionality of the charger and purchase a replacement battery if a faulty battery is indicated
• DO NOT store lithium-ion battery packs in a discharged state over a long period as this can damage the lithium-ion cells. For long-term storage, store batteries in a high charge state disconnected from the power tool
• The capacity of batteries will reduce over time. After 100 charge cycles, the battery’s operation time and the maximum torque performance of the driver will slightly reduce. This decline will continue until the battery has minimal capacity after 400 charge cycles. This is normal and not a fault with the battery pack.

Fitting drill bits and accessories

WARNING:

• ALWAYS remove the Battery from the drill before attaching, adjusting or removing accessories.

WARNING:

• DO NOT attempt to tighten drill bits (or any other accessory) by gripping the front part of the chuck and switching the tool on. This can lead to personal injury and can cause damage to the chuck

WARNING:

• NEVER fit any accessory or bit with a maximum speed lower than the no-load speed of he power tool.

1. Open the Chuck by rotating the Chuck (7) anti-clockwise
2. Place the drill bit or accessory centrally into the chuck
3. Tighten the ChuckJaws by rotating the Chuck Collar clockwise
4. When the drill bit or accessory is securely fastened, carefully run the Machine to test that it is running centrally, smoothly, and evenly. If the bit is ‘wobbling’ or not running centrally, release the chuck, check the accessory for damage, correct its position, retighten and test again.

Operation

Direction control

WARNING: NEVER change the direction of rotation while the tool is running. This may cause permanent damage to the tool.

• The direction of rotation can be set using the Forward/Reverse Switch (5)
• For anti-clockwise rotation, push the switch to the right
• For clockwise rotation, push the switch to the left

Note:

• When the Forward/Reverse Switch is in the central position, the drill is locked and cannot be switched on. Use this setting as a safety feature to prevent the drill from being switched on accidentally.
• If the motor carbon brush shows sporadic spark during use, it is a normal phenomenon

Torque control

Note:

• This cordless drill is equipped with a torque control clutch allowing the machine to be set to the correct torque for the individual application.
• The clutch settings are indicated by the symbols on the Torque Selector (2) Rotate the Torque Selector to select the desired setting: the higher the number displayed on the torque ring, the higher the torque produced by the too.

Gear selection

• Elect gear 7 on the Gear Switch (3) for the higher torque. A lower-speed gear is generally more suitable for driving screws and fasteners
• Select Gear 2 on the Gear Switch for the lower torque. A higher speed gear is for drilling and must not be used for driving screws and fasteners

Note:

• ALWAYS read the documentation provided with drill bits and accessories for the recommended or maximum speed setting and use the most appropriate gear. See ‘Specification’ for the maximum no-load speed of each gear.

Switching on/off

WARNING:

• ALWAYS wear adequate personal protection equipment when setting up and operating this machine.

1. To start the drill, squeeze the Trigger Switch (6)
   • Note:
   • If the Trigger Switch cannot be pressed down, check that the Forward/Reverse Switch (5) is not set to its middle position, which locks the device (see ‘Direction control’).
2. The speed of the drill is controlled by the movement of the trigger: the further the Trigger Switch is pressed down, the faster the drill will run
3. Release the Trigger Switch to stop the machine Screwdriver use

Note:

• Always use a universal bit holder when working with screwdriver bits. Do not mount screwdriver bits directly into the chuck

1. Select gear 7 using the Gear Switch (3)
2. Adjust the drill to the appropriate torque setting (see ‘Torque control’) When driving screws NEVER use the machine in drill mode

Note:
If in doubt about which torque setting best suits the application, start with a low setting and increase, should more torque be required (e.g. if the screw is not being driven far enough into the workpiece).
Drilling wood

1. Select the appropriate gear using the Gear Switch (3)
2. Rotate the Mode Selector (2) to the drill position Ensure that drill bits are suitable for wood, and are within the maximum capacity of this machine (see ‘Specification’)

WARNING:

DO NOT inhale wood dust. Wear adequate breathing protection. Some wood dusts may be toxic.

Drilling metal

1. Select the appropriate gear using the Gear Switch (3)
2. Rotate the Mode Selector (2) to the drill position
   • Ensure that drill bits are suitable for the grade of metal being drilled, and are within the maximum capacity of the machine (see ‘Specification’)
   • To ensure accuracy, mark the intended hole position using a hammer and center punch

WARNING:

• The drill bit and the workpiece will become very hot when drilling metal. DO NOT touch the bit and never allow it to come into contact with combustible materials when hot. Always use a suitable lubricant or cutting fluid, and drill at appropriate speeds.
• ONLY apply moderate pressure to the drill bit, ensuring efficient cutting and prolonged drill bit life
• Use a countersink bit to remove sharp burrs from the hole, preventing cuts and other kinds of injury

WARNING:

• If the power tool gets excessively hot in use, stop using the tool immediately and allow it to cool before continuing work. The cooling period can be reduced by operating the drill at maximum speed with no load.
• Always make sure the Motor Vents (4) are not blocked and do not allow dust to enter the body of the tool through the Motor Vents; dust, especially metallic dust, may damage or destroy the tool.

Function Button

Press the button, the Battery Capacity Indicator light

Battery Capacity Indicator

| <9.5| Flicker| X| X| X
< 10.5| Light| X| X| X
< 11.3| Light| Light| X| X
< 11.8| Light| Light| Light| X

11.8| Light| Light| Light| Light

• Then press the button, the Emergency Lamp light;
  Then press the button, the Emergency Lamp flicker;
  Then press the button, and the Emergency Lamp shuts down.

Maintenance

WARNING:

• ALWAYS disconnect from the mains power supply, before carrying out any maintenance/ cleaning of the charger. Remove the battery before carrying out any maintenance/cleaning of the drill.

Note:

• Both the drill and the charger contain no user-serviceable parts. If the device does not perform as outlined in this manual, return it to an authorized GMC service center for repair

General inspection

• Regularly check that all the fixing screws are tight
• Inspect the supply cord of the tool, before each use, for damage or wear. Repairs should be carried out by an authorized service center. This advice also applies to extension cords used with this too.

Cleaning

• Keep your tool clean at all times. Dirt and dust will cause internal parts to wear quickly, and shorten the machine’s service life. Clean the body of your machine with a soft brush, or dry cloth.
• If available, use clean, dry, compressed air to blow through the ventilation holes Clean the tool casing with a soft damp cloth using a mild detergent. Do not use alcohol, petrol, or strong cleaning agents
• Never use caustic agents to clean plastic parts

Lubrication

• Slightly lubricate all moving parts at regular intervals with a suitable spray lubricant Storage
• Store this tool carefully in a secure, dry place out of the reach of children

Disposal

• Always adhere to national regulations when disposing of power tools that are no longer functional and are not viable for repair.
• Do not dispose of power tools, or other waste electrical and electronic equipment (WEEE), with household waste.
• Contact your local waste disposal authority for information on the correct way to dispose of power tools.
• Read all instructions and product labels.
• When using electrical tools, follow all the precautions to reduce the risk of fire, electric shock, and other personal injury.
• Customer Service Email:service@phalanxtools.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>