Shuo W0513 Alarm clock Wireless Charger User Manual

Shuo W0513 Alarm clock Wireless Charger

5-in-1 Clock Wireless Charger User Manual

• Model： SY-W0513

Function Buttons

Operation manual

1. Power Connection
   • Plug the USB-A end of cable into the power adapter while plug Type-C end into the product, then the product can enter the normal working state.
2. Wireless Charging
   • This product can charge mobile phones, earbuds and watches at the same time.
   • The watch charging module is designed with a USB plug, easy to carry, the Special magnetic automatic flip structure can be compatible compatible with both Apple smart watches and Samsung smart watches.
   • The height of the bracket can be adjusted according to the size of the wristband.
   • Wireless charging status indicator (mobile phone and earbud have charging indicator, while watch without charging indicator)
   • Indicator Display: Power connected successfully –turn off after flashing twice
   • Standby – light off
   • Charging – light stays on
   • Fully charged – light off (Some models do not support this function) FOD – light flashes
3. Alarm Clock Functions
   • Buttons
   • Four Buttons: M Button，+Button，-Button Light Button
   • Time System Setting
   • Double click M button to setup 12-hour time system and 24-hour time system. In the 12-hour time system, PM will be displayed after 12:00.
   • Time Setting
   • Click M button once to enter Hour setting, adjust the value with +/- button; Press and hold the +/- button to adjust continuously.
   • After finishing the Hour setting, Click M button once to enter Minute setting, adjust the value with +/- button; press and hold the +/- button to adjust continuously.
   • Click M Button once to exit after the minute setting complete.
   • Alarm Clock Setting
   • Press and hold the “+/-” button to turn on or turn off the alarm clock,after turning on the alarm clock, the indicator light will be on.
   • While Alarm clock activated, press M button 3 seconds to enter alarm Hour setting, adjust the value with +/- button; Press and hold the +/- button to adjust continuously.
   • After finishing the Hour setting, click M button once to enter alarm Minute setting,adjust the value with +/- button; press and hold the +/- button to adjust continuously.
   • Click M button to end the setting after the minute setting complete.
   • After alarm clock rings, it automatically stops ringing after 3 minutes while no any operation.
   • Touch any button to enter snooze mode when alarm bell rings. Bell will ring again after 5 minutes,the indicator flashes during the snooze mode.
   • Press and hold M button to cancel the alarm clock after the alarm buzzing. The alarm clock setting for next day is still valid. Press and hold the “+/-” button to turn off the alarm clock permanently.
   • Display Brightness Setting
   • The clock brightness can be adjusted manually in 4 levels:M aximum, Medium , Low, dark , adjust the light brightness of the digital display with +/- button,after connecting to power,the clock keep the max brightness by default. Click the “-” button once to reduce the brightness by one level, click the “+” button once to increase the brightness by one level; the last click to turn off the display light.
   • Night Light Setting
   • Click the Light button to turn on the night light,the light brightness can be adjusted manually in 3 levels,click the button once to reduce the brightness by one level, the last click to turn off the night light.
   • Power saving function
   • After the power is disconnected, the internal button battery can be used to memorize the clock setting, and the clock does not need to be reset after the power connected again. 3.7.2 All functions are out while unplug the external power supply, functions restored when  power is connected.
4. Cautions
   • In order to ensure alarm clock, wireless charging ,clock and light night work at the same time, power shall be connected a QC3.0 and above or PD adapter. .When powered by 5V voltage, the wireless charger only supports 5W load or clock function.
   • Do not squeeze or collide.
   • Do not disassemble or put into the fire, water, to avoid short-circuit leakage.
   • Do not use wireless chargers in severe high temperature, humidity or corrosive environments to avoid leakage of damaged circuits.
   • Do not place it too close to magnetic cards (ID cards, bank cards, etc.) with magnetic strips or chips to avoid magnetic card failure.
   • Keep more than 20cm between the implanted medical device (pacemaker, implantable cochlea, etc.) and the wireless charger to avoid potential disruption to medical devices.
   • Keep children from the product in case they play the wireless charger as a toy to avoid accidents.
   • Keep the wireless charger and receiver device away from water and other liquids.
   • To clean the charger, make sure the power supply is disconnected.
   • Usage temperature: 0-45℃.
   • Usage humidity: 20-85% (40℃)

Warning : This product contains button battery, which can cause serious or fatal injury within 2 hours if swallowed. Batteries must be kept away from children. If you think the battery may have been swallowed or placed anywhere in your body, please seek medical assistance immediately.

• The pictures involved in this manual are all illustration. Final product is subject to the actual object.
• Inside package including : Clock wireless charger, USB charging cable, User manual.
• Power adapter is not included. Please purchase otherwise or use original adapter with the phone.

Specification

• Input: DC 5V/3A;9V/3A;12V/2A
• Output: Phone : 15W (compatible with 10W, 7.5W, 5W)
• Earbud : 5W (MAX)
• Watch : 2.5W (Compatible with both Samsung and Apple smart Watches)
• USB-A ：5V/1A（MAX）
• Charging efficiency: 73%
• Transmission distance ：≤6mm
• Work frequency: 115-350KHz
• Product size :2238689mm

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body: Use only the supplied antenna.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>