Shenzhen Shuo Yu Technology SYW0258 Alarm Clock Night Light Wireless Charger Instruction Manual

Shenzhen Shuo Yu Technology SYW0258 Alarm Clock Night Light Wireless

Charger

Function Buttons

Functions

Power Connection

1. Plug the USB A end of the cable into the power adapter while plug the Type C end into the product.
2. The product will be ready and stand by after all indicators are on.

Wireless Charging

1. Output: 15W
2. Indicator Display: Power connection successful blue light flashes once
3. Standby light off
4. Charging blue light on
5. Charged light off
6. FOD blue light flashes continuously

Alarm Clock Functions

1. Four Buttons: Alarm, +, –, Light.
2. Time System Setting:
3. Double click the Alarm button to set up the 12-hour time system and 24-hour time system. AM and PM will display while the 12-hour time system is set.

Time Setting

1. Click the Alarm button once to enter the minute setting, and adjust the value with +/–;
2. Click Alarm button once after minute setting, to enter the hour setting, adjust the value with +/–;
3. Click Alarm button a third time to finish the time setting.

Alarm Setting

1. Press “+” 3 seconds to activate or deactivate Alarm 1; Press “–” 3 seconds to activate or deactivate Alarm 2. The alarm indicator is on while the Alarm is activated;

2. While activated, press the Alarm button 3 seconds to enter the alarm minute setting, and adjust the value with +/–;

3. Click the Alarm button once after the alarm minute setting, to enter the alarm hour setting, adjust the value with +/–;

4. Click Alarm button a third time to finish the alarm time setting;

5. Alarm bell rings 3 minutes before the automatic switch-off while no any operation.

6. Touch any button to enter Sleep Mode when bell rings. Bell will ring 3 more times after 5 minutes. The indicator flashes and the Alarm button is out of function during Sleepy Mode. If a time setting is needed, please long press “+” to stop alarm 1 or long press “–” to stop alarm 2. All buttons will function normally;

7. The brightness of the clock light can be manually adjusted to four grades (dark, low light, sub bright, high brightness): “+” and “–” to manually adjust the light brightness of the digital display, the default is the brightest state after plugging in, each time you click ”
   “Decrease the brightness one stop at a time and turn off the clock display light one last time.

8. Time display brightness can also be adjusted manually to 3 grades (Min/Mid/Max). “+” and “–” can be used to adjust display brightness manually. The default grade is maxed brightness when power is connected. Single click “–” to dark the display one grade.

Night Light Setting

1. The night light can be set into 9 color modes: white, RGB shade, red, yellow, light green, green, light blue, blue and pink;
2. Touch the Light button once to turn on the night light with white color. Another touch shall allow you to set another color in turn as specified in 5. 1). The last touch will turn off the atmosphere light.

Eco power function

1. The button cell inside is only for timekeeping.
2. All functions are out during power disconnection. Functions are restored when power is connected.
3. Note

Attention: In order to function alarm, wireless charging, night light, and USB output altogether, power shall be connected by a QC2.0 or QC3.0 adapter. If connected by a 5V adapter, only wireless charging and alarm can work together.

1. Do not squeeze or collide.
2. Do not disassemble or put it into the fire, or water, to avoid short circuit leakage.
3. Do not use wireless chargers in severe high temperature, humidity or corrosive environments to avoid leakage of damaged circuits.
4. Do not place too close to magnetic cards (ID cards, bank cards, etc.) with magnetic strips or chips to avoid magnetic card failure.
5. Keep more than 20cm between the implanted medical device (pacemaker, implantable cochlea, etc.) and the wireless charger to avoid potential disruption to medical devices.
6. Keep children from the product in case they play the wireless charger as a toy to avoid accidents.
7. Keep the wireless charger and receiver device away from water and other liquids.
8. To clean the charger, make sure the power supply is disconnected.
9. Usage temperature: 0 45℃.
10. Usage humidity: 20 85% (40℃)
11. The pictures in this manual are all illustrations. The final product is subject to fact.
12. Inside package: alarm charger, charging cable, manual.
13. the power adapter is not included. Please purchase otherwise or use the phone original adapter.

Specification

• Input: DC5V/3A, 9V/3A 12V/2A
• Output power: 15W (MAX)
• Charging efficiency: 73%
• Charging distance: ≤8mm
• Frequency: 110.2-128.8KHz，
• Maximum wireless transmit Power: -7.85dBuA/m@10m
• Size: 145x116x73mm

Applicable Devices

Products qualified with Qi standard.

Manufacturer

• Shenzhen Shuoyu Technology Co., Ltd.
• Address: 30F East Block, Wenhua Bldg, 1027 Shennan East Road, Luohu District, Shenzhen, Guangdong, China

Importer

• Caliber Europe BV
• Address: Kortakker 10 4264 AE Veen, The Netherlands UP Global Sourcing UK (Ltd)
• Manor Mill, Victoria Street, Chadderton, Oldham, OL9 0DD， UK

FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>