WYZECFLP Pro Floodlight Cam User Guide

WYZECFLP Pro Floodlight Cam

INTRODUCTION

GET BETTER SECURITY WITH Cam Plus

Record Full-Length Videos
Get unlimited full-length video recordings.

Smart Al Detection
Detect people, packages, vehicles, and more.

Back-to-Back Event Recording
Capture everything without 5-minute gaps.

Exclusive Discounts
Get exclusive discounts on Wyze products. Subscribe or learn more at services.wyze.com.

Welcome to Wyze!
Hi! Thanks for getting your hands on a Wyze Cam Floodlight Pro, and if this is your first Wyze product, welcome to the Wyze family! You just made a commitment to a better, more connected lifestyle. Please read this guide carefully before setting up the device, and keep it in a safe place for future reference.

Disclaimer: The products, accessories, user interfaces, etc. illustrated in this guide are intended for reference only. Due to product updates, the actual product and the illustrations in this guide may vary.

IN THE BOX

SETUP

1. Download the Wyze opp and sign in or create an account.
2. Select Add Device> Cameras> Wyze Cam Floodlight Pro and follow the instructions in the opp.
3. Check your local laws for installation. If you are outside of North America, installation and wiring must be performed by a licensed electrician. Make sure you follow all code standards when doing wire installation.
4. WARNING: Risk of electrical shock!
5. Make sure you have a junction box for your fioodlight installation. If you need one installed, please contact a licensed electrician.
6. Verify that the power supply is a 720 V AC 60 Hz power source.
7. Disconnect power using the fuse or circuit breaker before continuing.

Notes: Do not use a dimmer switch or timer for this product.

You can mount the fioodlight vertically on the wall or overhang under eaves.

WALL MOUNT

Recommended Installation Location

Tip: When Wyze Cam Floodlight Pro is mounted 70 feet above the ground, it will detect motion up to 30 feet away.

Important: While positioning the camera for wall installation, find the “W” and arrows on the joint arm behind the camera. Make sure the arrows are in alignment. Do not rotate the camera past this point or completely around as this may twist or break the
connection line.

1. Remove your existing fioodlight and any brackets that may be attached if you are replacing a previousproduct.

2. Place the mounting bracket on the junction box. Align the 2 screw holes and tighten the bracket using matching bracket screws.
   Note: If you don’t have a junction box, please find a licensed electrician to install one and follow local building codes.

3. Use the ground wire screw to attach the ground wire to the mounting bracket.

4. Hang the fioodlight on the mounting bracket using the provided hook as shown in the picture.

5. Connect the hot wire (usually black) from your fioodlight to the hot wire from your junction box. Then connect the 2 neutral wires (usually white). Cap the wires using wire nuts and twist them 5-10 times. Gently tug on the wire nut to make sure it’s securely attached.
   IMPORTANT: If you are not sure which wire is which, please consult an electrician for safety.

6. Push the wires back into the junction box. Make sure the wires are not pinched between Wyze Cam Floodlight Pro and the mounting bracket.

7. Screw your Wyze Cam Floodlight Pro to the mounting bracket using the fioodlight screw.

8. Place the rubber stopper over the fioodlight screw to protect the screw. Apply caulk to mounting surface on all sides to ensure complete waterproofing.

9. Now adjust the angle of the camera so it is parallel to the ground.

OVERHANG MOUNT

Recommended Installation Location

Tip: When Wyze Cam Floodlight Pro is mounted 10 feet above the ground, it will detect motion up to 30 feet owoy.

1. While positioning the camera for an overhang installation, find the “E” and arrows on the joint arm behind the camera. Rotate the camera 180°, making sure that the arrows are in alignment. Do not rotate the camera around too far or repeatedly as this may twist or break the connection line.

2. Remove your existing fioodlight and any brackets that may be attached if you are replacing an older fioodlight.

3. Place the mounting bracket on the junction box. Align the 2 screw holes and tighten the bracket using matching bracket screws.
   Note: If you don’t have a junction box, please find a licensed electrician to install one and follow local building codes.

4. Use the ground wire screw to attach the ground wire to the mounting bracket.

5. Hang the fioodlight on the mounting bracket using the provided hook as shown in the picture.

6. Connect the hot wire (usually black) from your fioodlight to the hot wire from your junction box. Then connect the 2 neutral wires (usually white). Cap the wires using wire nuts and twist them 5-10 times. Gently tug on the wire nut to make sure it’s securely attached.
   IMPORTANT: If you are not sure which wire is which, please consult an electrician for safety.
   Note: The screw and rubber plug installation steps are the same as 8 and 9 for wall installation. The next steps are the same for both overhang and wall mounting. Apply caulk to mounting surface on all sides to ensure complete waterproofing.
   Note: We recommend leaving the ladder in place until after you’re done pairing the camera(s) and adjusting the fioodlight position.

7. Rotate and tilt the fioodlight so it points where you want it.

8. Restore power to the junction box using the circuit breaker or fuse box. The fioodlight will turn on for 15 seconds and the camera status light should fiash red.

WYZE CAM FLOODLIGHT PRO STATUS LIGHT GUIDE

WARRANTY

Your Wyze product is covered by a one-year limited warranty. You can view the limited warranty terms at https://wvze.com/return-warranty-policy or request a copy by contacting Wyze at +1 206-339-9646. Apple logo and App Store are trademarks of Apple Inc., registered in the U.S. and other countries and regions. Google Assistant, Google Home, Google Play, and the Google Play logo are trademarks of Google LLC. Wyze and Wyze Cam Floodlight Pro are trademarks of Wyze Labs, Inc.

Supplier’s Declaration of Conformity

Unique Identifier

• Trade Name: WYZE
• Model No.: WYZECFLP, WYZECFLPBL
• Responsible Party – U.S. Contact Information
• US Company Name: Wyze Labs, Inc.
• Address: 5808 Lake Washington Blvd NE Ste 300 Kirkland WA 98033 Telephone number or internet contact information: 1-844-999-3226

SPECIFICATIONS

• Model: WYZECFLP, WYZECFLP_CA, WYZECFLPBL, WYZECFLPBL_CA
• Connectivity: 2.4/5GHz Wi-Fi
• Weather Resistance: P65
• Input: Hardwired 120V~ 50/60Hz 0.61A

FCC WARNING

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following twoconditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limitsfor a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communi- cations. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/ TV technician for help.

FCC RADIATION EXPOSURE STATEMENT
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.

ISED RSS WARNING
This device contains licence-exempt transmitter(s)/ receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions: (1) This device may not cause interfer- ence and (2) This device must accept any interference, including interference that may cause undesired operation of the device.

ISED RADIATION EXPOSURE STATEMENT
This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body. The maximum antenna gain permitted for devices in the band 5725-5825 MHz shall comply with the e.i.r.p. limits specified for point-to-point and non point-to- point operation as appropriate.

NEED HELP?

• Contact our Support Team: https://wyze.com/support
• Join the Community:https://wyze.com/community

Scan the QR code to learn more

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>