WYZE WLPNLA Wall Mounted Night Light User Guide
- June 4, 2024
- Wyze
Table of Contents
QUICK START GUIDE
IN THE BOX
Wyze Night Light (2022) × 3
Easy Pull Tape × 3
Wall Mount Plate × 3
Quick Start Guide × 1
INSTALLATION
Installation Height
The recommended installation height is 1.6 ft (0.5 m) – 3.9 ft (1.2 m) above
the ground.
Sensing Range
The front PIR sensor’s range is 110°. The effectiveness of the sensor may be
impacted by ambient temperature, movement speed, and body size.
-
Remove the plastic from the Easy Pull Tape and then place the tape on the Wall Mount Plate.
-
Place the Wall Mount Plate with Easy Pull Tape at your desired location. Press hard and ensure the Wall Mount Plate is firmly attached to the surface.
Tip: Make sure the surface is clean and dry before placing. -
Wyze Night Light has a built-in magnet. To mount the night light place it onto the metal Wall Mount Plate.
-
Remove the night light by pulling it away from the Wall Mount Plate.
Wall Mount Plate Removal
Pull down the handle on the Easy Pull Tape and the tape will detach itself
from the surface.
Tip: Use the included Easy Pull Tape to make sure there is no residue
left behind.
CAUTION
- Wyze Night Light 2022 version CANNOT be linked with the previous 2021 version.
- Do not cover the front sensor because it will affect performance.
- Do not use bleach or any corrosive solvent to clean the surface of the product.
- Avoid installing it near heat sources or places with high fluctuations in temperature and humidity.
- Indoor-use only.
- Do not attempt to dismantle the product.
- If the product is put into long-term storage, please charge the product before storage.
- Follow local laws and regulations when disposing of this product.
- The battery is to be disposed of safely. Do not incinerate.
MODES
On: The light will always be on.
Off: The light will be turned off.
Auto: Light will automatically turn on and both the dusk-to-dawn sensor
and motion sensors are on.
Group uses : To link Wyze Night Lights together, switch all devices to
Auto. You can link up to 10 lights. In the first 30 seconds, the devices will
be in linking mode and blink
slowly. Once devices are linked, they will blink quickly.
Delete Group: To delete a previously paired group, turn to Off, then On,
and then quickly turn to Off again within 3 seconds.
Individual use: Switch the device to Auto and wait for 30 seconds to end
pairing mode.
STATUS LIGHT
Flashing red light
Low battery life
Solid red light
Charging
No light
Battery charged.
Tip: Please charge the device as soon as possible when the battery is low
to protect the battery life expectancy.
SPECIFICATIONS
Product model: WLPNL
Rated input: DC5V
Rated power: 0.25W
Color temperature: 2500K
Operating temperature: 41°F – 104°F (5 °C – 40 °C)
Product size: 3.2 in x 2.0 in x 0.6 in (81.5 mm x 51 mm x 15.3 mm)
Weight: 1.8 oz (50 g)
Battery type: 300mAh Lithium Polymer
WARNING: This product can expose you to chemicals including BPA, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov
FCC WARNING
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
IC STATEMENT
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: (1) this device may not
cause interference, and
(2) this device must accept any interference, including interference that may
cause undesired operation of the device.
NEED HELP?
Contact our support team at:
https://support.wyze.com
Join our community:
https://wyze.com/community
https://support.wyzecam.com/hc/en-us
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>