WYZE WWGH1 Wireless Gaming Headset User Guide
- October 30, 2023
- Wyze
Table of Contents
WYZE WWGH1 Wireless Gaming Headset
Product Information
- The product is a headset with a boom mic and a mute button.
- It comes with a USB dongle, a USB Type-C cable, and a mic foam cover.
- The headset has a power button, a multi-function button (MFB), and a volume wheel.
- The headset can be paired via Bluetooth or Bluetooth LE using the USB dongle.
- The headset has a battery level indicator, and it can be charged using the USB Type-C cable.
- The headset can be factory reset to clear the Bluetooth pairing.
Product Usage Instructions
- To turn on the headset, press the power button for 1 second. The red LED will turn on.
- To pair the headset via Bluetooth, press the MFB button for 3.5 seconds while the headset is turned on. The LED will flash blue while pairing and turn solid blue when paired.
- To pair the headset via Bluetooth LE, plug the USB dongle into the USB port on your device. The LED on the headset will turn white when paired.
- To pair the headset with a new USB dongle, press the power button 5 times to enter USB dongle pairing mode.
- To check the battery life of the headset, press the power button once while the headset is turned on. A voice prompt will announce the battery level.
- To charge the headset, plug a USB-C cable into the USB-C port on the headset.
- The LED will flash red while charging and turn solid red when fully charged. If the battery level is below 10%, the headset will prompt Battery low.
- To switch between Bluetooth and LE mode, press the MFB button twice.
- The LED status light is blue in Bluetooth mode and white in LE mode. Bluetooth LE mode will not activate if the USB dongle is not plugged in.
- To factory reset the headset and clear the Bluetooth pairing, press and hold the MFB button and the volume wheel for 5 seconds.
- Then, press and hold the power button for 15 seconds. The headset will prompt Factory reset when complete.
- To answer or end a call, press the MFB button once. To reject a call, press and hold the MFB button for 1 second.
- To mute the microphone during a call, press the mute button.
- To unmute the microphone, press the mute button again.
- Do not use the headset while driving or when the inability to hear surrounding sounds may present a danger to yourself or others.
- Do not use the headset if it emits any loud or unusual noises.
- Remove the headset immediately if you experience a warming sensation or loss of audio.
- Do not use mobile phone adapters to connect the headset to an airplane seat jack, as this could result in injury or damage due to overheating.
- Do not use the gaming headset as an aviation communication headset except in case of emergency.
- The product contains small parts that may be a choking hazard for children under 3.
IN THE BOX
- Wyze Wireless Gaming Headset × 1
- Boom Mic × 1
- Mic Foam Cover × 1
- USB Dongle × 1
- USB Type-C Cable × 1
- Quick Start Guide × 1
WARRANTY
- 12-month limited warranty. The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth SIG, Inc. and any use of such marks by Wyze Labs, Inc. is under license. Other trademarks and trade names are those of their respective owners. Select mobile devices require iOS 14.0+, and Android 7.0+.
- Disclaimer: The products, accessories, user interfaces, etc. illustrated in this guide are intended for reference only. Due to product updates, the actual product and the illustrations in this guide may vary.
BASIC OPERATION
Power On/Off
- Press the power button for 1 second to turn on the headset.
- The red LED will turn on.
- Press the power button for 1.5 seconds to turn off the headset.
- The red LED will turn off.
You can connect via Bluetooth® and Bluetooth® LE
Bluetooth Pairing
- With the headset turned on, press the “MFB” button for 3.5 seconds to enter Bluetooth pairing mode. The headset will prompt “Bluetooth pairing,” the LED will flash blue while pairing, and turn solid blue when paired.
Bluetooth LE Pairing
- Plug the USB dongle into the USB port on your device. The headset will prompt “Bluetooth pairing,” and the LED on the headset will turn white when paired.
- To pair the headset with a new USB dongle, press the power button 5 times to enter USB dongle pairing mode.
Switching Between Bluetooth and LE Mode
- To switch between Bluetooth and LE mode, press the “MFB” button twice. The LED status light is blue in Bluetooth mode, and white in LE mode. Bluetooth LE mode will not activate if the USB dongle is not plugged in.
Checking the Battery Life
- To check the headset’s battery life, press the power button once while the headset is turned on. A voice prompt will announce the battery level.
Charging
- To charge the headset, plug a USB-C cable into the USB-C port on the headset. The LED will flash red while charging. Once the headset is fully charged, the red LED will turn solid.
- Note: If the headset battery level is below 10%, the headset will prompt “Battery low.”
Factory Reset
- To factory reset, the headset and clear the Bluetooth pairing list, turn off the headset by pressing the power button for 1.5 seconds.
- Then, press and hold the power button for 15 seconds.
- The headset will prompt “Factory reset” when complete.
Auto-Off
- The headset will turn off automatically after 10 minutes of no activity or no media playing.
Play/Pause
- Press the “MFB” button once to play or pause the audio.
Volume
- Turn the volume wheel to adjust the volume level.
CALL CONTROLS
Phone Controls
- To answer/end a call
- Press the “MFB” button once.
- To reject a call
- Press and hold the “MB” button for 1 second.
- To mute the microphone
- During the call, press the mute button to mute your mic. To unmute your mic, press the mute button again.
TROUBLESHOOTING
- Cannot connect via Bluetooth:
- Factory reset the headset, then try to pair it via
- Bluetooth again.
- Cannot connect to USB dongle:
- Factory reset the headset, then plug the USB dongle in again.
WARNINGS
- DO NOT use your headset while driving.
- DO NOT use the headset at any time the inability to hear surrounding sounds may present a danger to yourself or others, e.g., while riding a bicycle or walking in or near traffic, a construction site or railroad, etc., and follow applicable laws regarding headphone use.
- DO NOT use the headset if it emits any loud or unusual noises. Turn off the headset and contact Wyze support for assistance.
- Remove the headset immediately if you experience a warming sensation or loss of audio.
- DO NOT use mobile phone adapters to connect the headset to an airplane seat jack, as this could result in injury or damage due to overheating.
- DO NOT use the gaming headset as an aviation communication headset except in case of emergency.
- Contains small parts, which may be a choking hazard for children under 3.
- This product contains magnetic materials. Consult your physician on whether this might affect your implantable medical device.
- To reduce the risk of fire or electrical shock, DO NOT expose this product to rain, liquids, or moisture.
- DO NOT expose this product to dripping or splashing liquids, and do not place objects filled with liquids, such as vases, on or near the product.
- DO NOT make unauthorized alterations to this product.
- Use this product only with an agency-approved power supply that meets local regulatory requirements (e.g., UL, CASA, VDE,
- DO NOT expose products containing batteries to excessive heat (e.g. storage in direct sunlight, hot surfaces, or fire).
- DO NOT wear the headset while charging.
- The gaming headset does not play audio while charging.
- To avoid hearing damage, use your headset at a comfortable, moderate volume level.
TROUBLESHOOTING
- Cannot connect via Bluetooth:
- Factory reset the headset, then try to pair it via Bluetooth again.
- Cannot connect to USB dongle:
- Factory reset the headset, then plug the USB dongle in again.
FCC WARNING
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/ TV technician for help.
US Radiation Exposure Statement
- This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment.
- The end user must follow the specific operating instructions for satisfying RF exposure compliance.
- This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- The portable device is designed to meet the requirements for exposure to radio waves established by the Federal Communications Commission (USA).
- These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue.
- The highest SAR value is measured at a distance of 0mm between the radiator and the head.
ISED Compliance Statements
- This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science, and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:
- This device may not cause interference. (2)This device must accept any interference, including interference that may cause undesired operation of the device
Canada Radiation Exposure Statement
- This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. The end user must follow the specific operating instructions for satisfying RF exposure compliance. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
- The portable device is designed to meet the requirements for exposure to radio waves established by the ISED. These requirements set a SAR limit of 1.6 W/kg averaged over one gram of tissue. The highest SAR value is measured at the distance of 0mmbetween the radiator and the head
CAUTION
- Risk of explosion if the battery is replaced by incorrect type disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion; leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas; a battery subjected to the extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas.
SPECIFICATIONS
- Product Name: Wyze Wireless Gaming Headset
- Model: WWGH1-F，WWGH1-L
- Product Size: 203.2 mm x 159.4 mm x 90.8 mm
- Product Weight: 235 g
- Power: 600mAh DC 3.7V
- Compatibility: Android 7.0+, iOS 14.0+
- Operating TemBperature: 32°F – 104°F (0°C – 40ºC)
- Operating Humidity: ≤85%RH
- Storage & Transport Temperature: -4°F- 140°F (-20°C – 60°C)
- Storage & Transport Humidity: ≤95%RH
- FCC ID: 2AUIUWWGH1
- IC: 25466-WWGH1
- Product Name: Wyze Wireless Gaming Dongle
- Model: WWGH1USB
- Product Size: 50.8 mm x 17.0 mm x 7.6 mm
- Product Weight: 5 g
- Power: Computer USB port (5V)
- Compatibility: Windows OS, Mac OS
- Operating Temperature: 32°F – 104°F (0°C – 40ºC)
- Operating Humidity: ≤85%RH
- Storage & Transport Temperature: -4°F – 140°F (-20°C – 60°C)
- Storage & Transport Humidity: ≤95%RH
- FCC ID: 2AUIUWWGH1USB
- IC: 25466-WWGH1USB
NEED HELP
- Contact our Support Team:https://wyze.com/support Join the Community: https://wyze.com/community
- Wyze and Wyze Wireless Gaming Headset are trademarks of Wyze Labs, Inc.
- Apple logo and App Store are trademarks of Apple Inc., registered in the U.S. and other countries and regions. Google Assistant, Google Home, Google Play, and the Google Play logo are trademarks of Google LLC.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>