Wyze WSPRK1 SPRINKLER CONTROLLER User Manual
- June 5, 2024
- Wyze
Table of Contents
WSPRK1 SPRINKLER CONTROLLER
**User Manual
**
WYZE SPRINKLER CONTROLLER
WSPRK1
Introduction
Congratulations on purchasing a Wyze Sprinkler Controller. This Quick Reference Guide describes how to install, operate, and maintain your controller. Please read the instructions below.
Package List
Controller Stations
Wyze Sprinkler is an 8-station controller. Each station is connected to a sprinkler valve. The specific valve turns on when it receives a signal from the controller, and then the sprinkler will start watering. When the watering task is finished, the controller will shut off the valve and turn on the next one in sequence.
Step-by-Step Instructions
Step 1 Drilling on the wall
Drill two holes at the installation position, the size of the holes is 6mm
× 40mm, and the distance between the two holes is 90mm. If the installation
wall is made of wood, please see step 3.
Step 2 Installing anchors
Tap the anchors into the holes on the wall.
Step 3 Mounting Screw the mount on the wall.
Step 4 Wiring Connect the power adapter, valve wires, and sensors to
corresponding terminals.
Step 5 Installing controller
Place the back of the controller at the lower end of the mount and push the
controller up into the mount.
Step 6 App setup
Download the Wyze APP and select “Add a product”, then the app will guide you
to complete the setup process. After finishing the system setup, you can
create the irrigation tasks.
Manual Controls
You can run the zone watering easily on the device. Press the left and right buttons to select a zone. Press the WATERING button (the upper one) to start a quick run immediately and press the STOP button (the lower one) to stop the watering.
Troubleshooting
One or more stations do not turn on:
- Faulty valve.
- Wire broken or not connected.
One station is stuck on and will not shut off:
- Faulty valve.
- Particles of dirt or debris are stuck in the valve.
- Valve diaphragm faulty
The controller is not online:
- Power adapter not plugged into an operational AC outlet.
- The Wi-Fi connection is unstable.
FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this de vice must accept any interference received,
including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for
compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help with important ann announcements Important Note:
Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
ISED Statement
-English: This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause interference, and (2) This device must accept any interference, including interference that may cause undesired operation of the device. The digital apparatus complies with Canadian CAN ICES-3 (B)/NMB-3(B).
This radio transmitter (ISED certification number: 26041-WSPRK1) has been
approved by Industry Canada to operate with the antenna types listed with the
maximum permissible gain indicated. Antenna types not included in this list,
having a gain greater than the maximum gain indicated for that type, are
strictly prohibited for use with this device.
Radiation Exposure Statement
This equipment complies with Canadian radiation exposure limits set forth for
an uncontrolled environment. This equipment should be installed and operated
with a minimum distance 20cm between the radiator & your body.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>