CLEANFORCE H13 Rainbow True HEPA Air Purifier User Manual

CLEANFORCE H13 Rainbow True HEPA Air Purifier

Important Safety Instructions

Read all instructions before using this air purifier to reduce any risk of fire, electric shock, or injury. To ensure safety, store these instructions for future use and make them accessible to other users. Make sure to include these instructions when handing over the air purifier to third parties.

• This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug If it still does not fit, contact a qualified electrician. Do not attempt to defeat this safety feature.
• This air purifier is intended for household and commercial use, not for industrial use. Do not use this air purifier as sole protection against harmful pollutants.
• Do not use this air purifier if you have restricted physical, sensory, or mental skills, or a lack of experience or knowledge unless supervised or instructed by a person who is familiar with the device.
• Children should not touch or operate the device and should be supervised at all times, when the purifier is in use.
• Do not use the air purifier in an area with toxidexplosive vapors/ liquids, oxygen tanks or near flammable, combustible materials.
• Place purifier in a location whereby air can circulate freely in, out and around the unit. Do not block the air inlets and outlets of the air purifier.
• Ensure the air purifier is positioned on a flat, stable, solid surface. Completely unravel the power cord prior to use. Never overstretch the power cord. Do not place air purifiers near heat sources such as stove tops, ovens.
• Do not place the air purifier near wet areas, like bathroom.
• To ensure safety with the power cord. Power cord should not run under rugs, runners or carpets as it can be a trip hazard. Don’t pull, carry or trap the power cord under doors or sharp edges. Do not unplug the air purifier by pulling on the power cord.
• Don’t handle the plug or air purifier with wet hands.
• Don’t use the air purifier with incorrect voltage as this may result in damage or injury to the user. The correct voltage is listed on the rating label.
• Before disconnecting or connecting the power cord, ensure the unit are switched off.
• Always switch off and unplug the air purifier before performing maintenance or troubleshooting checks.
• Always unplug the power cord before adding or removing parts and before cleaning.
• Don’t use the air purifier if the power cord or plug is damaged. Please contact our Customer Service.
• Only specialist personnel may perform repairs on electrical devices. Improper repairs may subject users to considerable danger. In the case of repairs, please contact our customer service.

FCC Warning

• This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• NOTE : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.
• If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to  which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
• To maintain compliance with FCC’s RF Exposure guidelines, This equipment should be installed and operated with minimum distance between 20cm the radiator your body. Use only the supplied antenna.

Product Introduction

• Touch Button
• Body (I LED Display
• Inlets
• Wheels G Outlets
• Sensor
• 4D Filter Cover
• Power Cord

Accessories

LED Display

1. LED Display
2. Three Fan Speed
3. Child Lock Mode ON
4. Filter life Indicator
5. CD A Automatic Mode ON
6. Particle value display
7. Filler Service life
8. Sleep Mode ON
9. WIFI Indicator

Specifications

• Air Purifier Part No.: CP-Rainbow
• Multi-Integrated Filter Part No.: CF-Rainbow
• Clean Air Delivery: Smoke Dust Pollen
• Rate{CAOR)
• Power: 47W
• Noise Level: 34-60dB

• 300 >300 >300

• 500 >500 >500 m3/h

• Motor Type: DC Motor
• Voltage: AC120V 60Hz
• Fitler service life: 3600 hours
• Dimensions: Width: 288mm ( 11.3 inches)
• Depth: 288mm (11.3 inches)
• Height: 649mm (25.5 inches)
• Weight: 7.0 KG (15.4 lbs)

Operating instructions

• Read all instructions before using your CleanForce air purifier.
• Unpack and remove all packing material. Remove your CleanForce air purifier from the plastic bag.
• Completely unravel the power cord and place your CleanForce air purifier on a flat, dry, stable surface. Be sure to place your CleanForce air purifier at least 12 inches(30cm) away from the wall on ALL sides.
• The air output vent should face towards the room – failure to do so may reduce unit efficiency. Inspect the power cord for signs of damage before use.

DO NOT USE IF THE CORD IS DAMAGED

Note : To ensure the normal operation of the air purifier, please remove the plastic bag from the internal filter before starting the machine!
The steps are as follows

1. Turn off and unplug the air purifier.
   

2. Pull the rear handle to take out thefilter cover.

3. Take out the Multi-Integrated Filter.
   

4. Remove all the plastic outer packages.

5. Install the Multi-Integrated Filter.
   

6. Install the filter cover back, plug in and press the power key.

Plug in your Clean Force air purifier and press the power key to turn the unit on. Next the machine will start the automatic mode, and the LED lights on top of the air purifier will display the air quality in three colors.
You can also use the Smart App to operate your air purifier.

1. Power
2. Timer
3. Fan Speed
4. Sleep Mode
5. Filter Reset
6. Child lock f)
7. WiFi Indicator
8. LED Light

Power Key
Paces the pow, key, the machos will start the autobahn mode, Press it again, the machine will enter standby mode.

Timer Key
The user can set the running time of the air purifier, 1-12 hours automatically on I off. Press the Timer key once to operate the unit for 1 hour, press the Timer key twice to indicate that the unit should operate for 2 hours, and soon. The maximum timing that can be set is 12 hours. When the timer runs out, the air purifier will shut down and enter standby mode.
Fan Speed Key
Touch the “Speed” key to enter the manual fan speed adjustment mode. The fan speed switches between levels 1-3 and auto mode.
Press the Sleep key, the light on the touch screen panel will be dimmed, the air purifier will enter the mute mode operation, and the LED display will go out. Press the sleep key again to cancel the sleep mode
Filter Reset Key
The indicator light for the Filter Reset key will flash at the end of the filter service life, to remind the customer to replace the filter. Once the filter has been replaced, long-press the Filter Reset key for more than 5 seconds until the flashing light goes out.
Child Lock Key
Press the lock key to enter the lock mode, other keys are invalid in this mode. Long-press the lock key {more than 3 seconds), to exit the lock mode, this will allow other keys to then operate normally.
WiFi Networking
Long press the WiFi key to enter the network matching mode See the details on the next page: section “Smart App”.

Smart App

Scan the QR code to download and install the Clear Force App, register an account.
Link the air purifier to the network for the first time ·

1. Open the Clean Force App, Click”+” bottom on the top-right, then click your air purifier model, select your WiFi network and enter the password.
2. Select the match mode on the top-right. The default mode is EZ mode. 3, Mode1: EZ mode. Long press “Wi-Fi” button for 3s to switch the match mode, make sure the indicator light flashes quickly.

• Select “Finish network configuration” on the app and click “next” Mode2: AP mode. Long press ‘WIFI” button for 3s to switch the match mode, make sure the indicator light flashes slowly.
• Select “Finish network configuration” on the app and click “next”. Connecting the ‘Smarties-XXXX’ hotspot, then return to the App.
• The smart app starts finding the device and adding it to the device list After successfully linked to the network, the WiFi indicator stops flashing and stays ON.
• If it fails to link to the network for a long time, the WiFi indicator goes out, and the device stops pairing the network.
• If you want to relink the network, press the Wifi key again to repeat the network configuration operation. After configuring the network and binding the device according to the instructions, you can use the smart app to control your device auctions, you can use the smart app to control your device.

Link To Smart Home Hub
This device support Dysart Speaker, Tall Genie and Alexa Echo The method is as follows·
After linking the device to the Wi-Fi network through CleanForce App, do the following steps to connect the device to the smart speaker. Smart speaker Apps may change the actions, these are for reference only.

Alexa Echo

• Completed the Alexa Echo’s configuration process first, then following the next steps: Open Alexa App, tap on “Skills” in the Alexa app menu, then search.
• “Smart life. Tap “Enable” to enable the Skill. Enter the Clean Force App account and password, then tap “Link Now” to link your TuyaSmart account to enable the Skill. Now you can start your smart home journey.

Multi-Integrated Filter Instruction

General information

CleanForce Rainbow air purifier Contains 1 pcs of Multi-Integrated filter.

The Multi-Integrated filter is composed of plastic pre-filler, nonwoven cloth, HEPA filter, and activated carbon, it removes:

Replace The Filter

When the indicator light of the filter seivice life flashes, the filters need to be replaced.

1. Tum off the air purifier and unplug it.
   

2. Pull the rear handle to take out the filter cover.
   

3. Take out the used Multi-Integrated Filter
   

4. Remove all the plastic outer packages of the new filter  Install the filter cover back.

5. Install the new Multi-Integrated Filters

6. Plug in the air purifier,
   

7. Press the filter key more than 3 seconds

Note :
Install the new Multi-Integrated Filters & Plug in the air purifier, Press the filter key more than 3 seconds

1. You should not miss this reset step or the air purifier may not operate normally
2. The Rainbow air purifier can not operate without the filter.

Care and Maintenance

Please follow the steps below for regular maintenance for your air purifier to workat optimum capacity.
Before any maintenance operation, be sure to turn off the machine through the power key and unplug the device.

• Filter over(Air inlets)
  Remove the covers on both sides of themachine,cleanlhem regular1ywith waler or vacuum cleaner

• Fan
  Regularly clean the fan port with a vacuum cleaner. Do not wash with water or dismantle the fan

• Sensor
  Removethefiller cover and wipe the sensor surface regularly with a dry cotton rod.

• Recommend to replace the Multi-Integrated fillers every 6-12 months; Calculate based on the fan speed of medium grade, which uses 8 hours every day. The replacement frequency depends on the use duration and working environment
• When the filter needs replacing, the filter indicator light will flash Attention! When your air purifier stops working, please checkthe filters
• When the filter life bar decreases to the last grid and flashes, indicating that the filters need replacing.

Warranty Policy

Dear User,

• If you encounter problems with your air purifier, or your expectations for your CleanForce product are not met, you can contact us using either of the following methods·
• Call our service hotline: +1 213 289 3385 Or contact us by email : support@cleanforceair.com
• Your CleanForce air purifier is guaranteed and warranted against defects in material and workmanship, under normal residential use, for up to 2-years from the date of purchase. (excluding filters).

Warranty
Policy Not covered

warranty

• Proof-of-purchase and warranty card from CleanForce must be provided.
• Claims must be made within the warranty period.
• Cause of failure must not be a result of user error.
• Failure to operate, maintain or use product in accordance with the user manual.
• Lack of proof-of-purchase, warranty card
• Warranty card model does not correspond with the machine.
• Product damage caused by force majeure.
• Damage caused by unstable voltage power and/or power source used does not comply with the national electric safety standards (AC 120V, 60HZ).
• Damage caused by improper transport, installation, use, maintenance or storage by users

Warranty Card

Maintenance record
| |
| |
| |
| |
| |
| |

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>