Bousnic p-collar 670 Dog Training Collar with Remote User Manual
- June 14, 2024
- Bousnic
Table of Contents
Bousnic p-collar 670 Dog Training Collar with Remote
Package Contents
-
Remote
-
Receiver Collar
-
Charging Cable
-
Test Light Tool
-
User Manual
-
Contact Points
-
Silicone Caps
-
Contact Spring Sheet
overview
The Remote
Display Screen
Receiver Collar
Important Safety Information
This is the safety alert symbol. It is used to alert you to potential injury hazards. Obey all safety messages that follow this symbol to avoid possible injury.
WARNING
Not for use with aggressive dogs. Do not use this product if your dog is prone
to aggressive behavior. Aggressive dogs can cause severe injuries to their
owners and others. If you are not sure if this product is right for your dog,
please check with your veterinarian or a certified trainer.
CAUTION
Safety during on-leash training.
While learning during on-leash training, your dog should be on a strong leash.
It should be long enough for him to attempt to chase an object, but short
enough for him not to reach a road or other unsafe area. You must also be
physically strong enough to restrain your dog when he tries to chase
something.
Risk of skin damage.
A collar worn for too long or made too tight on the pet’s neck may cause skin
damage ranging from redness to pressure ulcers. This condition is commonly
known as bed sores.
- Avoid leaving the collar on the dog for more than 8 hours per day.
- When possible reposition the collar on the pet’s neck every 1-2 hours.
- Never connect a lead to the electronic collar, It will cause excessive pressure on the contacts.
- If a rash or sore is found, discontinue use of the collar until the skin has healed. If the condition persists beyond 48 hours, see your veterinarian.
- This product is not a toy, please keep away from children.
- This product is only for use with healthy dogs over 6-month old.
-
Charge The Remote And Receiver Collar
USB C Charging Port
When charging, the red light will come on and be steady. When fully charged, the screen will display the fully charged battery compartment and the red light will be flashing.
When charging, the red light will come on and be steady. When fully charged, the light will turn green and be steady.
(Caution: Please charge the product with a 5V 1 A adapter. Do not use an adapter that does not meet the specifications.) -
Turn On The Remote
-
Turn On The Receiver Collar
Click the power button to turn on the receiver collar. The receiver collar will vibrate once and the green light will flash once.
Press and hold the power button for 2 secs to turn off the receiver collar. The receiver collar will vibrate twice and the red light will flash twice.
-
Fit The Receiver Collar
The contact points must have direct contact with the dog’s neck skin. Check the tightness of the collar by inserting one finger snugly between the collar and neck.
-
Beep
Delivers a beep tone with non-adjustable volume to the receiver collar.
-
Vibration
Delivers a vibration with non-adjustable level to the receiver collar.
-
Static Stimulation
Delivers currently selected level static stimulation to the receiver collar.
Note: Please use the Static Stimulation with caution. Some dogs may not respond to lower levels. See “How To Find The Best Static Level For Your Dog”{Page 8). “O” means none,”16″ means the highest level of static stimulation.
-
How To Find The Best Static Level For Your Dog
Very Important: Always start at the lowest level and choose the level that is best for your dog.
Follow the steps below to find the best Level: -
Starting at Level l, press the static button to see the dog’s reaction.
-
Gradually increase the stimulation levels until your pet reliably responds to the stimulation.
-
If your dog continues showing no response at Level 6, check the fit of the receiver collar. If your dog has long or thick hair, install contact spring sheet, or dog’s hair will need to be trimmed around the contact points, If the “Contact Points” is no contact with the dog’s skin, there will be no static stimulation.
Note: If all of these steps have been done and the dog continues showing no reaction, see the “How to Use Test Light Tool” (Page 10).
Main Features
Beep Vibration and Static training mode
0-16 adjustable static level
Battery status display for the remote
Receiver collar is IPX7 waterproof
(Caution: Remote is non-waterproof)
Remote range is 3/4 mile, 1300yard
Long life Lithium Polymer battery
USB C charging port
Security Lock Switch
Support maximum 2 receiver collars with 1 remote
How to Use Test Light Tool
- Make sure the Remote and Receiver Collar are on paired.
- Put the test light tool vertically on the 2 contact points, making sure the metal wire has direct contact with the top of the 2 points.
- Press the static button on the remote. The test light will be lighted.
The higher the static level is the redder the light will be.
Note: For dog with shorter coats use the 2 contact points and install the conductive silicone caps onto the contact points to make it softer, which may be better for your dog’s skin. For dog with thicker coats, please install contact spring sheet.
Training Tips
If you want to correct the dog’s bad behavior, for example, barking, please follow these training steps.
- Put a separate non-metallic collar on your dog’s neck above the receiver collar, and attach an 8-10 feet leash.
Caution :
- Be sure the extra collar does not put pressure on the contact points.
- Hold the leash and the remote.
- Choose your pet’s recognition static level.
- As soon as your pet is barking, press the stimulation button and give the command “No” or “No barking”.
- Release the stimulation button immediately once your dog stops barking and praise it.
- If your pet ignores the stimulation, increase the Intensity Level by l to 3.
- Practice this training in several different scenes.
Pairing
Note: You may skip this step because the set is already paired with a factory setting.
- Make sure the receiver collar is turned off. Make sure the channel of remote is on “Dog l”.
- Press and hold the power button of receiver collar for 3 secs until the red and green lights flash alternately.
- Press and hold the “Beep” and “Vibration” buttons of remote at the same time to pair the receiver collar.
- Pairing successfully, the receiver collar beeps 3 times and the green light flashes 3 times.
Two Receiver Collars System
Part I : Pairing 2nd Receiver Collar.
Note: You need own an additional receiver collar to own.
-
Make sure the receiver collar is turned off. Make sure the channel of remote is on “Dog 2”.
-
Press and hold the power button of receiver collar for 3 secs until the red and green lights flash alternately.
-
Press and hold the “Beep” and “Vibration” buttons of remote at the same time to pair the receiver collar.
-
Pairing successfully, the receiver collar beeps 3 times and the green light flashes 3 times.
Part II : Receiver Switching.
You are able to train 2 dogs separately. Regulator channel select the dog to train.
How to adjust the length of the Receiver Collar
-
How to lengthen the length of the Receiver Collar ?
-
How to shorten the length of the Receiver Collar?
-
lf you have to cut some of the strap off, please do singe the collar end immediately with a lighter to avoid fraying.
-
Buckle the collar and pull it to 2 directions to make sure it’s secure and well-threaded after the adjustment.
Question & Answer
Q: Is the static sate for my pet?
A: The static electricity is safe for your pet. So please feel at ease
using the collar. But please do select the appropriate static electricity
level. And do start from the lowest level and increase the level gradually
until your dog responds.
Q: How old does my pet have to be before using the electronic training
collar?
A: Your pet should be able to recognize basic obedience commands such as
“Sit” or “Stay”. Pets should be at least 6 months old before using the
training collar.
Q: Once my pet is trained and has been obeying my commands, will he have
to continue to wear the receiver collar?
A: It is recommended to wear it until you completely correct the dog’s
bad behavior.
Q: Is the receiver collar waterproof?
A: Yes, the receiver collar is IPX7 waterproof. But the remote is not
waterproof. Please keep the remote away from water.
Q: Will I get exactly 1300yard of range with the electronic training
collar?
A: The effective wireless communication range will be affected by
terrain, weather, vegetation, and interference from other radio equipment.
Q: How can I get support when I have product problems?
A: Any problems about the product, please feel free to contact us at any
time via s support@bousnic.com. We will do our
best to help you.
Troubleshooting
My pet does not respond when i press a button.
-
Make sure the receiver collar has been turned on.
-
Make sure the remote channel 1 or 2 is correct with the receiver collar. If not, please pairing the remote and the receiver collar again. Refer to “Pairing” (Page 12) for more information.
-
Check if the battery in the remote or the receiver collar is low.
If so, please get them fully charged. -
Make sure the receiver collar is placed snugly against your pet’s neck. Refer to “Fit The Receiver Collar’ ( (Page 6) for more information.
-
Terrain, weather, vegetation, transmission from other radio devices, and many other factors can impact the control range of the product.
Warranty
1-Year Warranty
The original purchaser for this unit is provided with a 1-YEAR Warranty.
The warranty begins on the date of purchase. For the first year, coverage is
provided for both parts and labor on warranty repair services. After the first
year, the Limited Lifetime Warranty covers parts only, and does not cover
labor fees and Accessories. Accessories such as straps and batteries are
covered for the first year only. All shipping fees incurred, the cost of
accessories after the first year, and labor fees associated with out of
warranty repair work are the customers’ responsibility.
Not Covered Under Warranty
We DO NOT offer warranty for products that have been bought secondhand or were resold. Issues of replacement and refunds on units purchased in less than 30 days from an authorized dealer must be addressed to the dealer directly. If the products purchased from an authorized dealer are 30 days after the date from the date of purchase, please send the units to us for service and repair. We DO NOT cover the cost of repairs and replacements due to misuse by the owner or dog, improper maintenance, and/or lost units. The warranty is void if the unit has been altered or an unauthorized person has damaged the unit while attempting repair work.
Procedure for Repair Work
If the unit is malfunctioning, please refer to the ‘Troubleshooting” in the manual before sending it back for service. A copy of the sales receipt showing the purchase date may be required before warranty work is initiated. Please include a brief explanation outlining the problem, and include your name, address, city/state/ zip code, daytime phone number, evening phone number, and email address.
Compliance FCC – USA
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
CAUTION: Modification or changes to this equipment not expressly approved by the manufacturer may void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Customer Support
support@bousnic.com
@Bousnic
MADE IN CHINA
Documents / Resources
|
Bousnic p-collar 670 Dog Training Collar with
Remote
[pdf] User Manual
p-collar 670 Dog Training Collar with Remote, p-collar 670, Dog Training
Collar with Remote, Training Collar with Remote, Collar with Remote
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>