Bousnic 320B Dog Training Collar User Manual
- June 4, 2024
- Bousnic
Table of Contents
Bousnic 320B Dog Training Collar
Specifications
-
Package Dimensions
8 x 6.46 x 1.89 inches; 14.89 Ounces -
Material
Nylon -
Closure Type
Button -
Target Species
Dogs -
Training Modes
Beep, Vibration, Safe Shock -
Charging method
Rechargeable -
Working Range
Up to 1000 Feet -
Receiver waterproof level
IP67 -
Brand
Bousnic
Introduction
These Bousnic shock collars for dogs provide adjustable Vibration(1-8) and Static Shock(1-16) settings in addition to a typical “Tone” mode. The adjustable nylon collar suits dogs with neck sizes ranging from 8 to 26 inches, and the varied modes can be adjusted to your dog’s disposition.
You can train dogs anywhere with the remote that comes with this dog training collar, which has a range of up to 1000 feet. The remote also has a dual channel for training two dogs at once.
Do you find it difficult to train your dog?
No matter how much you care for your dog, undesired habits make you feel helpless. The safe, effective dog training collar from Bousnic is the best option in this situation. Fix behavioural issues. Teach fundamental obedience. strengthens communication aid in achieving training objectives For someone with expert experience or someone new to e-collars, that system is genuinely ideal.
Waterproof & Durable IP67
The collar receiver is IP67 waterproof, giving your pets the most freedom
possible while participating in outside activities. Additionally, it is built
of sturdy, high-quality materials.
(The remote cannot withstand water. Keep it away from water, please.)
Comfortable and Soft Prongs
Dogs with short coats use the short prongs, while those with longer, thicker coats need the longer probes. Conductive silicone prongs and metal prongs are available in two pairs (short and long). Install the metal prongs, then put on coordinating silicon covers.
How Should I Use a Dog Training Collar?
- Carefully read the user manual. Before using the collar on your dog, be familiar with how to use it.
- Installation of the collar receiver. Select the proper contact prongs.
- Secure the collar around the canine’s neck. Make sure the dog’s skin is touched by the prongs and that the collar is secure and pleasant.
- Start your dog’s training. If the dog doesn’t respond, switch to the vibration mode first, then the beep mode, and finally the shock mode. Start each mode at the lowest level possible, then gradually move up to the next level until the dog responds.
- Make directives clear by repeating and reinforcing them. Reward them for their desired positive behaviour.
Information about Safety
To ensure a secure and comfortable fit, please read and adhere to the directions in the handbook.
- Refrain from leaving the dog’s collar on for longer than 12 hours each day. Every one to two hours, reposition the collar on the animal’s neck if at all possible.
- You should never attach a lead to an electronic collar; doing so puts too much pressure on the connections.
- Please make sure the silicone caps are on the metal prongs before putting the collar on. Check the contact area every day for indications of a sore or rash. If discovered, wait until the skin has healed before using the collar again.
FAQs
Why do the collars turn off after a few hours? This didn’t happen with our first ones and they aren’t dying just turning themselves off.
I noticed that they go into a “sleep” type mode if a correction is not needed
for some time.
I just pressed the button on the collar and it “woke up”.
Does the receiver turn itself off if it hasn’t been used for several minutes?
It does turn itself off sometimes, but only after several hours. All you have to do is hit the on/off button again to turn them back on.
Can you control the collar independantly for each dog or when depressing the button does it activate both collars at same time?
Theres a button to switch from collar kne to collar two. So it is independent control.
Why does the transmitter only wake up after pressing shock, vibrate, or beep? Shouldnt the 1/2 button wake the transmitter as to not confuse the dog?
I thought that also but if you hold the button down for an extended amount of time (over 0.25 sec?). I’m an active user and the last thing I want to do is signal the dog when they didn’t do anything warranting correcting. Now when I’m waking up the transmitter, I wake it up using the light correction function.
Can i get replacement charger?
Where can I buy replacement remote . I lost it
Can I order just the nylon collar? The ends on my frayed.
Yes. And be sure and burn the ends with a lighter so they won’t fray.
Can I connect 2 dogs on 2 different remotes so both dogs can be controlled by 2 handlers?
yes, if you buy an extra remote, you can use 2 remotes to control 2 receivers separately. One remote control 1 receiver.
Are there replaceable prongs?
Yes there are.
where can i order a replacement charger?
I would assume from the manufacturer.
Will these collars work on a 8 pound dog?
I use these collars on my 9lb and 13lb Chihuahuas. The 9lb female just needs the collar to vibrate for correction – the collars are fit loosely and they still work. The 13lb male occasionally needs a quick shock and again I don’t have the collars fit tight – they fit loose and still are effective. I could tighten the collars but I don’t need to.
Is there a way to order additional silicone prongs?
Yes on website but if you don’t leave the collar on for days I recommend you leave them off that’s my opinion
Will one remote control both collars at the same time?
Yes. I have 2 labs 2 collars 1 remote
Can this one be used for 5 month old puppy that weights 15 lbs?
Yes! We used it on our Chihuahua, the earlier you start the easier the training. Now we’re using it on our 5 month golden doodle. Try to not use the shock feature and you’ll be good to go.
Does the remote control the collars separately?
Yes the one remote controls the two collars separately by a button that switches back and forth from first collar to second.
I bought these collars and one of them loosens while my dog is wearing it. Is there a way to make it stay tight without returning them?
Check the threading of the belt. I took the clip and device off belt, pulled the slip piece off, put the device back on the belt, put the slip piece back on, then the clip, run the end of the belt back through the slip piece. Adjust tightness as needed. Trim excess, leaving enough for future expansion
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>