MEGWR TF-X1 Dog Training Collar for Large Dog User Manual

MEGWR TF-X1 Dog Training Collar for Large Dog

SAFETY INSTRUCTIONS

Safe use statement

1. Use of this product on aggressive dogs is prohibited. Aggressive dogs can cause serious injury or death to their owners or others. If you are not sure whether the product is suitable for your dog, consult a professional training Dog trainer.
2. Do not allow children to play with this product. Please put the product out of reach of children

Electric shock safety statement

1. Make sure your dog is healthy before using the product. If you are unsure about this, consult your veterinarian.
2. When the device is turned on, the human body should avoid contact with the electric shock contact of the product.
3. If skin and sores are found on the wearing area, please stop using this product until the skin is healthy.

Safety Statement for wearing and training

1. Keeping you and your dog safe while training is vital. Your dog will need a strong lead to prevent overreaction during training and to hold him tightly to prevent him from running around.
2. The wearing time of the dog trainer should not exceed 12 hours a day, and please adjust the wearing position every 1-2 hours.
3. This product is suitable for dogs weighing over 7lb and aged over 6 months.
4. Do not use this product as a matching collar for pet leash.
5. Check whether the contact area of the electric shock contact on the neck of the dog is rashes and sores are very important.
6. It is okay to cut the long coat around the throat, but it is not recommended to shave it completely.
7. Before playing with the dog, please remove the device to avoid triggering it by mistake.
8. The 1P67 standard indicates that the equipment can be placed in water up to one meter deep for half an hour, and the internal part of the product will not enter water, but also prevent dust.

Note: The IP67 standard is the result of static laboratory tests.

COMPONENTS

PARAMETER

Receiver

Transmitter

Receiver collar is IP67 waterproof and dustproof, the remote control is not waterproof.

Function
Remote control enhanced visual design with digital display

• Strap Size:8-25in
• 4 modes: beep, vibration, E-shock,Dog Finder
• 18 levels of electric shock and 8 levels of vibration
• Remote can be paired with 3 receivers simultaneously
• Fast charging, both of the remote and receiver battery power display
• 2500Ft range and IP67 waterproof receiver (remote not waterproof)

RECEIVER INTRODUCTION

Transmitter Introduction

User operation

1. Charge the product before using it
   When the transmitter is charging, the battery column icon flashes water. The charging time is 1.5-2 hours. Battery charge after full, battery column icon long bright.
   When charging the receiver, the red light of the status light is on for a long time, and the charging time is 1.5-2 hours. When the battery is fully charged, The status indicator is steady green.

2. Turn it on/off
   Long press the receiver key for 2 seconds, the screen is lit up, indicating successful startup operation;In the startup state, the green light of the status indicator blinks once every 5 seconds (the operation status indicator will turn off after 10 minutes of display). Hold down the key for 2 seconds and the screen darkens, indicating successful shutdown.

3. Remotely shut down

4. Switch channel setting

5. The default channel for a single receiver is channel 1, and channel switching will be turned off. If you need channel switching, please turn on the channel switching function first.

6. In standby mode, press and hold the key of the transmitter for 5 seconds to turn on and off the channel switching function.

7. When the channel switching function is turned on, the channel icon will gradually light up; when the channel switching function is turned off, the channel icon will go out station by station.

8. Channel setting

9. When the channel switching function is enabled, press the key of the transmitter to switch between channel 1, Channel 2 and channel 3; When the receiver receives the channel switching instruction of the transmitter, the cyan light of the prompt lamp flashes 5 times.

10. When the channel switching function is off, press the CH key of the transmitter to switch between the paired channels,When the receiver receives the channel switching instruction of the transmitter, the cyan light of the prompt lamp flashes 5 times.

11. Lock key
    Flip down the lock key switch to open the lock key function,The lock key icon lights up. When any key is pressed, the transmitter has no function response and the lock key icon flashes，Pull the lock button up to disable the lock button function.

12. Set the shock level
    When the screen is on, short press the button or button to adjust the shock level.The shock level is adjustable from 0-18,0 is off.

13. Vibration level setting

14. When the screen is on, press the button of the transmitter and the vibration icon flashes to enter the screen for setting the vibration level.

15. Short press keys or key to adjust the vibration level.

16. Vibration is adjusted at levels 1-8.

17. The vibration icon will automatically exit the vibration level setting after flashing for 5 seconds.

18. Dog Finder

19. In the standby state, press the transmitter button to turn on the receiver dog search function and press the indicator light for the first time，The white light blinks quickly, and the transmitter dog icon blinks. 10 minutes later, the transmitter automatically shuts down.

20. Press the key again to switch the breathing light display to the prompt light, and the transmitter search dog icon lights up.

21. Short press the key for the third time to turn off the receiver dog search function.

22. Train the operation
    In the standby state, press the key and the receiver will chirp for 1 second after receiving the instruction; Long press the key , the receiver continuously chirps 10 times before closing.

23. Matching
    When the receiver is turned on, briefly press the key twice to enter the pairing state. At this time, the blue light flashes.
    When the transmitter switches to the channel to be paired, only one receiver can be paired for each channel.
    At the same time, press the key of the transmitter for 2 seconds, and the transmitter sends the pairing command to the receiver, and the channel number of the transmitter flashes.

The blue light stays on for 3 seconds

Matching successful, the receiver prompt light blue light will be on for 3 seconds.
In the pairing state, if the pairing is not successful for more than 30 seconds, the receiver will automatically exit the pairing state

Transmitter Factory Reset
Within 15 seconds of restarting, press and hold the key for 2 seconds, and the backlight flashes for 5 times to indicate that the factory is successfully restored

Low battery power
When the battery electric shock of the receiver is less than 1 grid, the red light of the status indicator blinks once every 5 seconds, indicating that the receiver will automatically shut down after 20 minutes.

When the battery electric shock of the receiver is less than 1 grid, the red light of the status indicator blinks once every 5 seconds, indicating that the receiver will automatically shut down after 20 minutes.

Setup guide
Choose the right gear according to the dog’s temper and tolerance for shock. Start training at the lowest gear.
For example, if the dog responds to the shock gear with ear twitching, tongue licking, neck tightening, etc., this is the right gear. The shock range varies according to training conditions, and if the dog is highly inattentive, a strong level is needed to stimulate him.

Install receiver

Install the E-shock contactors
According to the actual use, select the long/short E-shock contactors and install them on the back of the product.

Please use appropriate force, otherwise the device will be damaged.

Install the silicone protective sleeve
Then choose long/short conductive silicone protective sleeve to directly cover the E-shock contact, which can effectively reduce the physical damage of the shock contact to the dog’s skin.

Functional testing

After assembly, functional testing is recommended. Follow these steps to test.

1. Short press the key of the transmitter to test the sound, and the receiver will beep for 1 second.
2. Short press the key of the transmitter for vibration test, and the receiver will vibrate for 1 second according to different vibration levels.
3. Press the test board on the shock column of the receiver, short press the key of the transmitter to carry out the shock test, and the light on the test board will be lit. The higher the shock level, the brighter the light.

The wearing of receiver

The neck circumference ranges from 8 “to 25”. Before putting on the collar, adjust the buckle and slip buckle so that the collar is the right size. Make sure that the shock contact is firmly attached to your dog’s neck.

FAQ

Q: Why does the receiver not work when the transmitter is shocked?
A: There are 3 possible reasons for this problem. The first is that the transmitter and receiver are not paired, so try repairing. Second, the shock contact does not touch the skin, so please try again to adjust the tightness of the collar to ensure good skin contact. Third, the level setting is not high enough, so try it increase the output level of the shock function

Q: Is the product safe and humane?
A: All means of receiving do not cause any direct harm to the no thingies, but make them feel very uncomfortable. Even if this is the case, do not overuse this product on objects. Please refer to the manual for all safety statements.

Q: Receiver and transmitter not working?
A: There may be one reason for this problem. Firstly, the transmitter and receiver are not powered on. Please refer to the manual for startup operation. Secondly, the battery of the transmitter and receiver is exhausted. Please charge the receiver and transmitter. The charging time is about 2 hours.

Troubleshooting

**** 2. Cannot start after charging

| 1. Please charge and try again after full charge

2. Please contact the seller for exchange

Unable to charge| 1. The receiver red light does not light up or the transmitter screen does not light up during charging

2. When charging, the receiver red light is on or the transmitter screen is on, but the battery cannot be charged

| **** 1. Please check whether the charging line interface is in good contact

2. Please contact the seller for exchange

The receiver does not respond when the transmitter is operating| 1. Check whether the machine is turned on

**** 2. Check whether the channel number is selected incorrectly

**** 3. Check whether the transmitter and receiver are not paired

4. The receiver is damaged

| 1. Turn on the receiver

2. Please adjust the channel number

**** 3. Please pair transmitter and receiver again

**** 4. Please contact the seller for replacement

Terms of Use & Limitation of Liability

1. Terms of Use
   Your use of the product constitutes your acceptance of all the terms, conditions and statements contained in this Manual

2. Use it correctly
   The product is designed for pets that need training. Proper use includes checking the product’s instruction manual and any specific “safety” and “care” statements.

3. Prohibit illegal use and prohibit use
   This product is suitable for pets. This training device is not intended to harm or annoy pets. Failure to follow the instructions may violate local laws.

4. Scope of responsibility
   The Manufacturer shall not be liable for any direct, indirect, punitive, non- material and other indirect losses arising from the incorrect use or misuse of the Products, and the buyer shall assume all risks and liabilities for the use of the products.

5. Terms and conditions modification
   The manufacturer reserves the right to change the terms relating to certain products. Conditions

Certification Statements

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

(1) This device may not cause harmful interference.
(2) This device must accept any interference received, including interference that may cause undesired operation.
Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Recycling Information &Battery Disposal
Please observe the regulations for electronic and electrical devices to be disposed of in the respective country. In some countries or regions, this device must be recycled. If this device is no longer required, it must not be disposed of with normal municipal waste. Separate collection of spent batteries is required in many regions; check the regulations in your area before discarding spent batteries. For more recycling information, please refer to local regulations.

MANUFACTURER: Quanzhou Purplebox Electronics Co.,LTD
ADDRESS:Floor 3&4, No.41 Wan Rong Street, Wansheng Community, Wan’ an, Luojiang, Quanzhou, Fujian, China
Email: support@megwr.com
Website: www.megwr.com

References

• Registrant WHOIS contact information verification | Namecheap.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>