MEGWR DM-912 GPS Pet Fence System Instruction Manual

MEGWR DM-912 GPS Pet Fence System

Product Information

Specifications

• Product Name: GPS Pet Fence System
• Safe Area Radius: Up to 1000 meters
• Main Features: Wireless, GPS-based, Stimulus Mode

Product Description
This wireless GPS pet fence system uses satellite technology to define a safe area for your pets with a radius of up to 1000 meters. It automatically stimulates when your pet goes out of the safe zone and stops when they return.

Components

1. GPS fence collar
2. USB charge cable
3. Reflective nylon belt
4. Test light
5. 2 sets of conductive pin

Product Usage Instruction

Operation Instructions

1. Turn on/off the System

   • Power On: Hold the power button until the LED display shows.
   • Power Off: Hold the power button until the LED display turns off.

2. Acquiring the Satellite Signals
   The GPS fence system needs to acquire satellite signals before use.

   • Go outdoors to an open area.
   • Power on the GPS fence system and wait for the signal symbol to flash, indicating it is searching for GPS signal and positioning the initial point.
   • Wait for about 1-2 minutes until successfully acquiring signals. If unsuccessful, the LED display will show an error message.

3. Set up the Safe Area Distance
   Follow the instructions in the manual to set up the safe area distance within the 1000-meter radius.

4. Set up the Stimulus Mode
   Configure the stimulus mode based on your pet’s behavior using the mode button and adjustment keys.

5. How to wear it
   Securely attach the GPS fence collar with the reflective nylon belt around your pet’s neck.

6. Recharge
   Use the provided USB charge cable to fully recharge the system before use. It takes approximately 3 hours to charge fully.

7. Important Notes

   • This product is not suitable for aggressive dogs.
   • Proper fit of the collar belt is crucial for effective functioning.

FAQ

• Q: Can this system be used for aggressive dogs?
  A: No, this product is not suitable for aggressive dogs as it may result in serious injury or harm.

• Q: How long does it take to fully charge the GPS fence system?
  A: It takes about 3 hours to fully charge the system. The battery indicator will stop flashing when fully charged.

Components

1. GPS fence collar
2. USB charge cable
3. Reflective nylon belt
4. Test light
5. 2 sets con ductive pin

WARNING

• Not for aggressive dogs. Do not use this product if your dog is aggressive, or if your dog is prone to aggressive behavior. Aggressive dogs could result in death or serious injury.
• Risk of skin damage. Please read and follow the instructions in this manual. Proper fitness of the collar belt is important.

Product Description

This all-new wireless GPS pet fence system uses satellites to accurately locate and define the safe area for your pets. The safe area is up to a circle of 1000 meters radius. If your dog wanders out of the safe area the fence system will automatically start stimulating. And the stimulus will immediately stop once your dog comes back to the safe area.

Main Features

1. Real wireless fence system without any wire and flags layout;
2. Maximum signal range is up to 1000 meters radius with GPS positioning technology;
3. Variety stimulus modes: warning beeper, vibration stimulus, and static shock stimulus;
4. Automatically start stimulus once your dog wanders out of the safe area;
5. Flexible and adjustable stimulus intensity from level 0 to level 9 to fit various-size dogs;
6. The GPS fence system is rechargeable with a built-in battery and waterproof;
7. Visual setup operation on LED touching screen;
8. Magnetic charge port,100% waterproof for all circumstances.
9. Over-correction protection;

Keys Definitions

• 1. Power button:
  • Long press: Power on or Power off the fence system
  • Short press: re-positioning the initial point
• 2. M button:
  • Long press: searching and positioning the initial point.
  • Short press: set and switch the stimulus mode
• 3 & 4: adjust stimulus intensity or adjust safe area distance
• 5. Digit Display:
• 6. GPS Signal Indicator: indicates the GPS signal strength.
• 7. Beeper mode: warning tone beeper stimulus
• 8. Vibrate mode: vibration stimulus
• 9. Static Shock mode: static shock stimulus.
• 10. Battery Indicator: blank and flashing is low battery alert.
• 11. Screen lock: The screen would lock up if no operation for more than 5 seconds.
• 12. Unlock the screen: press + and – at the same time.
• 13. Magnetic charging port: charge for the fence system.
• 14. Contact Point: deliver the static shock stimulus.
  • Power Saver: flashing “——” on screen after 10 seconds no operation
  • Sleeping Mode: flashing”—”on screen after 5 minutes of no operation.

Charging the GPS Fence System

• Please fully charge the GPS fence system before using it and it will take about 3 hours.
• When charging the battery indicator will flash in green color and stop flashing when fully charged.
• Low battery alert: when the battery indicator is blank and fast flashing it means low battery and please recharge it.

Operating Guide

Note:
You should fully charge the battery before you use the GPS fence system for the first time. Charging a full battery takes about 3 hours.

1. Power on/off the GPS Fence System
   Power on: Hold the power button until the LED displays. Power off: Hold the power button until the LED display is off.

2. Acquiring the Satellite Signals
   The GPS fence system must acquire satellite signals before you put it on your dog. Acquiring satellite signals will take a few minutes.

   • a) Go outdoors to an open area;

   • b) Power on the GPS fence system (as per Step 1 above) and the signal symbol flashes; Now the GPS fence system automatically starts searching the GPS signal and positioning the initial point at the current position. It will take about 1-2 minutes.

   • c) Once successfully searching and positioning the symbol will stop flashing and show the signal strength of connected satellites and the GPS origin lock up; while failure the LED display will show “ER” Please try again or change another place for GPS searching and positioning. shows the GPS signal strength
     Re-positioning the initial point
     When your dog goes out beyond the safe area and you want to set up a new safe area you can create a new initial point. you just need to do as below:

   • a) press both + and – at the same time to unlock the screen.

   • b) short press the power button, when the LED display shows “= = “, Repositioning success. NOTICE:

   1. This GPS fence system is only for outdoor usage and without shelter at the top.
   2. The GPS signal will be affected by the building, obstacles, rainy or cloudy weather, etc.

3. Set up the Safe Area Distance
   Successfully acquire the GPS signal and then short-press the power button to set up the original point. After that press the M button to set up the safe area boundary as follows.

   • a) Long press M button;
   • b) Press +/- button to increase and decrease the safe area distance; the distance default starts from 03 level( 30 meters);
   • c) The safe area distance setting is as follows:
     Display Value| Actual Remote Distance (Unit: meter)
     ---|---
     3| 30
     4| 40
     5| 50
     …| …
     98| 980
     99| 990
     A0| 1000

NOTICE:

  1. The actual distance is 10 times the value displayed
  2. The screen will turn off in 10 seconds once the positioning process is completed. You can press any key to light up the screen display.
  3. To avoid the initial radius distance being too short and the dogs will be punished unnecessarily, the minimum radius distance is limited to 30 meters.
  4. The screen will lock up if no operation for more than 5 seconds, just need to press + and – at the same time to unlock it.

4. Set up the Stimulus Mode
   • There are 3 kinds of stimulus for choice: tone beeper, vibrate stimulus, and static shock stimulus. You can choose any one or any combination of them.
   • There are 9 intensity levels for vibration and static shock stimulus except tone beeper.
   • The stimulus mode and intensity levels are as following table:
     Level| Beeper| Vibrate| Shock
     ---|---|---|---
     0| Deactive| Deactive| Deactive
     1| Active| Lowest| Lowest
     …| N/A| …| …
     9| Highest| Highest
   • Stimulus settings and operations are as follows:
     The system will automatically start stimulating when your dog comes to the position where there is only 1meter to the boundary and the dog will be warned by a beeper; if the dog goes further and goes out of the boundary of the safe area, the dog will be punished by vibration and shock. Once the dog comes back to the safe area the device will stop punishing.
     Note: please test the stimulus function before setting up: press both the

• and – buttons at the same time the fence system will activate the beeper, vibrate, and shock stimulus in a row (you need a test light to test the static shock function).
  Then you can set up the stimulus mode and intensity as follows:

  *  **a)** Short press the M button switch to the beeper stimulus and then you can press + / – to choose “1” to activate the beeper stimulus or “0″ to deactivate the beeper stimulus;
  *  **b)** Short press the M button switch to vibrate stimulus and then you can press + / – to choose “0″ to deactivate the vibrating stimulus or “1”, “2”…“9” to activate the vibrate  

  stimulus; you can choose only one intensity level every time;

  *  **c)** Short press the M button to switch to static shock stimulus and then you can press + / – to choose “0″ to deactivate the static shock stimulus or “1”, “2”…“9” to activate the static shock stimulus; you can choose only one intensity level every time;  

  Over-correction Protection:

  *  **d)** The vibrate or shock stimulus is 18 seconds every 30 seconds which is a stimulus cycle. There are a total of 3 stimulus cycles for both vibrate and shock.
  *  **e)** If your dog goes out of the safe area the stimulus will start from 3 cycles of vibrate stimulus and then 3 cycles of shock stimulus (if you activate both vibrate and shock stimulus); the stimulus will stop after all 3 cycles stimulus even though your dog is still out of the safe area to avoid over-correction.
  *  **f)** There isn’t a 3-cycle limit for beeper stimulus. When the dog goes out of the safe area the beeper stimulus is active and it won’t stop until the dog comes back safe area.

  5. How to wear it

     • Put the nylon belt on the fence system and wear it on your dog’s neck with proper tightness.
     • Important: the proper fitness and placement of your collar are important for effective training. The contact points must direct contact with your dog’s skin.

  6. Recharge

  7. Low battery alert
     When the battery is low, the battery symbol will flash.

  8. The device is equipped with a magnetic charging cable, you just need to adapt it to the charger which can output 5v,1A electricity.
     Important Notes

  9. The fence system might not position the initial point due to the poor satellite signal. So, please use this fence system in an open area, which do not have high-rise buildings around it.

  10. This product is only for behavioral training of pets such as dogs or cats. Do not use it on humans.

  11. Please keep this product away from children to avoid their playing causing unintended electric shock.

  12. DO NOT leave the collar on your dog for more than 8 hours per day.

  13. The fence system has a built-in rechargeable battery. Please fully charge it before using, it to avoid any unexpected shutdown or a dissatisfactory result during training.

  14. When the device is put on the dog’s neck, please make sure the tightness is appropriate. Being too loose or too tight will affect the training effect or cause discomfort to the dog.

FCC WARNING

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE:
This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>