Tenda MW5G AC1200 Whole Home Mesh WiFi System Installation Guide
- June 4, 2024
- Tenda
Table of Contents
Tenda MW5G AC1200 Whole Home Mesh WiFi System
Package contents
- Mesh5 x2
- Power adapter x 2
- Ethernet cable x 1
- Quick installation guide x1
Install the Tenda Wi-Fi App
Download the Tenda WIFI App on your mobile device by searching for Tenda WIFI in App Store/Google Play or by scanning the QR code. Then, install the App.
Connect the primary node
The first node you set up functions as the primary node, while the rest is referred to as the secondary node. 1. Use the included Ethernet cable to connect a LAN port of your modem or the Ethernet jack to the WAN/LAN port of any node. This node is your primary node. 2. Use one of the included power adapters to connect the primary node to a power source, the LED indicator Eights solid green. Wait about for 40 seconds. The system completes startup when the LED indicator blinks green.
Set up the primary node for internet access
- Go to the Wi-Fi network list on your mobile device, select the SSID of the primary node, and enter its password. The default SSID and password are specified on the bottom label of any node.
- Run the Tenda Wi-Fi App and follow the onscreen instructions to connect the primary node to the internet. After the primary node is connected to the internet, its LED indicator lights solid green.
Connect the secondary node to the internet
- Place the secondary node:
- In an elevated, open position with coverage area of your existing nova Wi-Fi network.
- Keep your nodes away from electronics with strong interference, such as microwave, induction cooker and refrigerator.
- Use the other power adapter to connect the secondary node to a power source. Its LED indicator lights solid green. Wait about for 40 seconds. The secondary node is connecting to another node when its LED indicator blinks green.
- Observe the LED indicator of the secondary node until its LED indicator lights one of the following colors:
- Solid green Good connection
- Solid yellow Fair connection
- Solid red Disconnected
- If the LED indicator of the secondary node does not light solid green, relocate it according to step 1 in IV to get it better connected.
- To access the internet:
- Wired devices: Connect wired devices to the LAN ports of your nodes.
- Wireless devices: Connect wireless devices to your Wi-Fi network using the SSID and Wi-Fi password you set.
- If you want to manage the network anytime anywhere, access the App, tap and use your account to login.
FAQ
- How can I remove a node from my Wi-Fi network?
- Tap the node on the Tenda Wi-Fi App, tap.in the upper-right corner, and choose Delete Note: Removing operation restores the node to factory settings
- Can Aid another new set of node to expand my network coverage?
- Yes. Open Tenda Wi-Fi APP, tap Settings in the lower-right corner, tap Add nova, and follow the on-screen instructions to add
- How to restore my network to factory settings?
- With your nodes powered on, hold the RST button of your primary node down using a paper clip for about 6 seconds, release when the LED indicator blinks fast. Your network is reset successfully when the LED indicator lights solid on then blinks fast again. And all nodes are restored to factory settings.
- My 2.4 GHz Wi-Fi-enabled devices, such as a home security camera, cannot connect to my nova Wi-Fi network. What should I do?
- Step 1. Connect your smart phone used for setup to your nova Wi-Fi network. Step
- Run Tenda Wi-Fi App, tap Settings, Smart Assistant, and Enable. Your smart phone connects to the 2.4 GHz Wi-Fi network. Step
- Use the smart phone to set up your 2.4 GHz Wi-Fi-enabled device guided by its App
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures. Operations in the 5.15-5.25GHz band are restricted to indoor use
only This equipment should be installed and operated with a minimum distance
20cm between the device and your body
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. (2) To
avoid unnecessary radiation interference, it is recommended to use a shielded
RJ45 cable
WARNING: The mains plug is used as disconnect device; the disconnect
device shall remain readily operable.
Declaration of Conformity
Hereby, Shenzhen Tenda Technology Co., Ltd. declares that the radio
equipment type Mesh5 is in compliance with Directive 2014/53/Eu The full text
of the EU declaration of conformity is available at the following internet
address: http://www.tendacn.com/en/service/download-cata-101.htm
Operating Frequency:
- 2.4 GHz: EU/2400-2483.5MHz (CH1-CH13)
- 5 GHz: EU/5150-5250MHz (CH36-CH48)
EIRP Power (Max.):
- 2.4 GHz: 19.26 dBm
- 5 GHz: 22.68 dBm
- Software Version : V1.0.0.X
- For EU/EFTA, this product can be used in the following countries:
FCC Statement
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device is for indoor usage only.
Operation is subject to the following two conditions: (1) this device may not
cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Radiation Exposure Statement
This device complies with FCC radiation exposure limits set forth for an
uncontrolled environment and it also complies with Part 15 of the FCC RF
Rules.
This equipment should be installed and operated with minimum distance 20cm
between the device and your body.
Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter. Operating frequency: 2412-2462MHz, 5150-525OMHz
NOTE: (1) The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications to this equipment. (2) To avoid unnecessary radiation interference, it is recommended to use a shielded RJ45 cable.
Caution: Adapter Model: BN036-A12012E/BNO36-A12012B/BN036-A12012U Manufacturer: SHENZHEN HEWEISHUN NETWORK TECHNOLOGY CO, LTD. Input: 100-240V AC, 50/60Hz, 0.4A Output: 12V DC, 1A —DC Voltage
Operating Environment
Temperature: 0’C-40’C Humidity: (10-90)% RH, non-condensing
RECYCLING
This product bears the selective sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU in order to be recycled or
dismantled to minimize its impact on the environment. User has the choice to
give his production competent recycling organization or to the retailer when
he buys new electrical or electronic equipment.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>