Tenda SP3 Smart Wi-Fi Plug Installation Guide
- June 4, 2024
- Tenda
Table of Contents
Tenda SP3 Smart Wi-Fi Plug
Getting to know your device
| Blinking orange: InIt1allzIng and starting
---|---
I L ED Indicator| Solid o range, Not connected to a 2.4
GHz WIFI network
Blinking bl ue: Connecting to a
2.4 GHz W IFI network
Solid blue: Connected to a 2.4
| GHz WIFI net work
| Off: Powered off. or turned off using the App or vole react laved devices
|
Button| Press II to power on/off the socket.
Hold It down for about 5 seconds and release I t when t he LED I n ducat or blinks or anger. The Smart Plug Is restored to factor y se tings success fully. Follow the q u ick Inst allative on gum de to config rue It again.
Maximum power of the Smart Plug:
- SP3 SP6
- UK 2300W 2990W
- EU 2300W 3680W
Common appliances and their power:
- Common appliances Power
- Coffee Maker 800 w
- Desk Lamp 235 w
- Tower Fan 50 w
- Humidifier 260 w
- Toaster 850 w
- LCD 270W
Configuring the device
Note:
• The Smart WI-Fi Plug only supports 2.4 GHz WIFI network.
• The default SSID (WIFI name) of the Smart Plug Is Tenda_ Smart Plug _xxxx.
xxxx Indicates the last four characters of Its MAC address which can be found
on the device.
-
Download the Tenda Bell App onto your mobile WI FL-enabled device, such as a smart phone, by searching for Tenda Bell In the App Store or Google Play or by scanning the QR code.
Then, Install the App. -
Follow the Instructions In the App to configure your Smart Plug.
FAQ
-
What devices can I control with the Smart WI-Fl Plug?
-
You can control desk lamps, coffee makers, humidifiers, tower fans, and any other small household
appliances whose rated power does not exceed the maximum power of the Smart Plug. -
02: What should I do when the LED Indicator of the Smart WI-Fl Plug lights solid orange?
A2: Try the following solutions: -
Check whether the WIFI network of your wireless router Is enabled. If not, enable It.
-
Check whether the WIFI name or password of your wireless router Is changed. If so, reset the Smart Plug, and connect It to your wireless router again with the new WIFI name or password.
-
Reset the Smart Plug, and reconfigure It using the Tenda Bell App.
Reset method: Hold down the power button (!) for about 5 seconds and release It when the LED Indicator blinks orange. -
How to control the Smart WI-Fl Plug with voice-activated devices, such Amazon Alexa or Google Assistant?
-
In your Tenda Bell App, tap the Smart Plug In the Device page, then G > Q (for Amazon Alexa) or •:· (for Google Assistant) to get the help.
For more questions, please visit www.tendacn.com/en/faq/default.html to get online supports.
CE Mark Warning
This is a Class B product. In a domestic environment, this product may cause
radio interference, in which case the user may be required to take adequate
measures. This equipment should be installed and operated with minimum
distance 20cm between the device and your body.
NOTE: (1) The manufacturer is not responsible for any radio or TV
interference caused by unauthorized modifications to this equipment. (2) To
avoid unnecessary radiation interference, it is recommended to use a shielded
RJ45 cable.
For PLUGGABLE EQUIPMENT, the socket-outlet shall be installed near the
equipment and shall be easily accessible.
For passthrough devices, plug the power strips into the integrated electrical
sockets of the devices, but devices of the same or another type not be stacked
in normal use.
Declaration of Conformity
Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio equipment
type SP3 is in compliance with Directive 2014/53/EU. Operating Frequency:
EU/2400-2483.SMHz (CH1-CH13) EIRP Power (Max.): 12.9dBm Software Version:
V1.1.0.7 Hereby, SHENZHEN TENDA TECHNOLOGY CO., LTD. declares that the radio
equipment type SP6 is in compliance with Directive 2014/53/EU. Operating
Frequency: EU/2400-2483.SMHz (CH1-CH13) EIRP Power (Max.): 12.9dBm Software
Version: V1.1.0.7 The full text of the EU declaration of conformity is
available at the following internet address:
http://www.tendacn.com/en/service/download-cata-101.html
RECYCLING
This product bears the select I’ve sorting symbol for Waste electrical and
electronic equipment (WEEE). This means that this product must be handled
pursuant to European directive 2012/19/EU In order to be recycled or
dismantled to minimize Its Impact on the environment. User has the choice to
give his product to a competent recycling organization or to the retailer when
he buys a new electrical or electronic equipment. Operating Temperature: orc –
40″C Operating Humidity: (10% – 90%) RH, non-condensing
Technical Support
Shenzhen Tenda Technology ca., Ltd.
6-8 Floor, Tower E3, N0.1001, Zhong’s hanuman Road, Nanshan District,
Shenzhen, China. 518052
- USA hotline: 1-800-570-5892
- Toll Free: Dally-9am to 6pm PST
- Canada hotline: 7-888-998-8966
- Toll Free: Mon – Fri 9 am – 6 pm PST
- Hong Kong hotline: 00852-81931998
- Global hotline: +86 755-2765 7180 (China Time Zone)
- Website: www.tendacn.com
- E-mail: support@tenda.com.cn
Copyright
© 2019 Shenzhen Tenda Technology ca., Ltd. All rights reserved. Tenda Is a
registered trademark legally held by Shenzhen Tenda Technology ca., Ltd. Other
brand and product names mentioned herein are trademarks or registered
trademarks of their respective holders. Specifications are subject to change
without notice