BKIRNP 6588 12V Battery Powered Ride On Car Instruction Manual

BKIRNP 6588 12V Battery Powered Ride On Car

About BKIRNP Products
We are professional manufacturing company to produce and sell electric cars for kids. We are committed to producing impressive products for your kids’ fun at very affordable prices. At the same time we have the good customer service for solving all of the issue which encountered by our customers. BKIRNP will always be with you.

Battery
Please charge for 12 hours before initial use. After initial charge follow the charging time on the specifications.

SPECIFICATIONS

WARNING
ADULT ASSEMBLY REQUIRED

WARNING
CHOKING HAZARD – SMALL PARTS. NOT FOR CHILDREN UNDER 3 YEARS OLD.

TOOLS REQUIRED

HARDWARE

PARTS

PRODUCT ASSEMBLY

1. Flip vehicle over and lay it on a level surface. Remove all parts and packaging from the vehicle body.
2. Fix the [Rear Axle] in the designated slot. Make sure rear axle is positioned evenly on each side. Use [8 Screws] to secure the rear axle.
3. Insert the [Gearbox] into the rear axle.(pay attention to the left and right)
4. Slide a [Wheel] onto the rear axle and secure it by replacing a [Nut/Washer]. Snap on a part [Cap]. Repeat on the other side.
5. NOTE: Use [2 Plastic Wrenches] (one on each side) and rotate in opposite directions to tighten nuts.
6. First insert the [2 Springs] and [Part I] into both ends of the [Front Axle] first. Then insert the front axle into front frame and the steering column into the designated hole on the front axle. Using [Iron Wire Pin] & washer to secure it in place.
7. Slide a wheel onto the front axle and secure it by replacing a nut/washer. Snap on a part cap. Repeat on the other side.
8. Flip the car. Join the connector from the steering wheel to the connector from the steering mount.
9. Remove the nut and bolt from the [Steering Wheel], slide it on the steering mount, and then replace the nut and bolt to secure it.
10. Within the seat, insert the connector from the battery into the designated terminal on the circuit board.
11. NOTE: Make sure the connector is oriented correctly to fit into the terminal.

ATTENTION

1. Please connect picture 1,the power connector before assembling the seat. Then press the Start Button as shown in picture

2. Otherwise, the car will not start because of no power supply.

3. After charging, please unplug the charger first ,then press the Start button as shown in picture

4. Otherwise, the car will not start because of no power supply.

• Attach the [Seat] with 2 screws.
  Snap on the [Windshield] and side [Mirror Set].

• Insert [2 Frame Lights] to the [Back Bar].
  Insert the back frame assembly into the rear of the car.

DASHBOARD DIAGRAM

Push down on the pedal to drive forward/reverse. Release the pedal to slow down and stop.

CONNECTING THE REMOTE CONTROL

First time using the remote control you need to match remote mode.

1. step. Holding down forward and backward buttons at the same time for 3 seconds to start match mode.
2. step. After LED flicking starting up the trucking car to match remote mode which will be automat-ically stopped once LED light lit up.

BLUETOOTH

1. Put your audio device near the media player and turn the car on.
2. Press Mode on the media player and wait until you pair your device through bluetooth success-fully
3. Then select your desired song on your device playing it

Remote Control:

1. Holding down forward and backward buttons on the remote controller at the same time for 3 seconds to start up matching mode.
2. After LED flicking please turn on the truck car to match with remote controller.

TROUBLESHOOTING

connectors
Charger not connected to socket or outlet| Completely plug in the charger
Battery does not last| Battery does not have a full charge| Fully charge the battery
Battery is warm and makes a slight noise while charging| Normal| Normal
Slow speed| Low battery| Fully charge the battery
Overloaded vehicle| Reduce the weight on the vehicle
Uneven or sloped road| Drive on flat pavement
Vehicles shakes while driving| Loose connection to motor| Ensure the motor is properly connected to the battery
Difficulty shifting between forward/reverse| Attempting to shift while vehicle in motion| Only shift when the vehicle is at a stop
Vechicle is silent| Steering wheel is not properly connected| Properly connect the steering wheel connector
Forward and reverse switch is flipped| Gearboxes are installed incorrectly| Make sure the L gearbox is on the left and R gearbox is on the right

QR CODE for product installation explaination

BKIRNP will always be with you.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>