IBE BBS14 Bench Bread Slicer Instruction Manual

IBE BBS14 Bench Bread Slicer

Description

Installation Instructions

Installation Area

1. Avoid direct sunlight.
2. Install the Slicer in a cool, clean, dry, well-ventilated, and well-lit area.
3. Do not expose the machine to corrosive or salty air.
4. Install the Slicer in areas that can withstand the weight and vibration of the machine.
5. Place the Slicer horizontally on a rigid and stable surface. If not, there are two conditions will happen:
   • a. Vibrations and errors are minimized.
   • b. The structure of the machine may deform over time if not leveled.

NOTICE If the Bread Slicer vibrates seriously during the operation, please put the cardboard or plastic sheet underneath the bottom of the machine.

Electrical Connection

1. Before connecting Slicer to the electrical supply, check that the details on the rating plate correspond to the details of your electrical connection.
2. Make sure the outlet is near the Slicer and easily accessible so that in event of an emergency it can be unplugged easily
3. Avoid sharing a single electrical outlet with other devices.
   • WARNING! NEVER USE EXTENSION CORD. LOW AMP SUPPLY COULD DAMAGE THE SLICER OR CAUSE A FIRE.
4. Connect the Grounding Wire to the ground in order to avoid electrical shock.
5. If the Slicer emits excessive heat, smoke, an offensive smell, or an unusual noise, turn off the power and unplug the Slicer from the electrical outlet immediately.
   • CAUTION THE SLICER MUST BE GROUNDED.

Operation

Prior to use

Before using the Slicer for the first time, wash all parts thoroughly, taking particular care to remove all grease and oil from surfaces by using a clean cloth. Dry all parts thoroughly before reassembling.
WARNING! BEFORE CLEANING, ASSEMBLING, OR DISASSEMBLING THR SLICER, MAKE SURE THE SLICER MOTOR IS OFF AND THE PLUG IS REMOVED FROM THE OUTLET OR POWER SOURCE.

Directions for use

1. Before slicing, Please put the loaf on the Upper Slide Board.
2. Then, set the correct height of the in-feed with the Pressing plate. (Please press lightly).
3. Pull down the pusher on the loaf.
4. Close the Protection cover and turn on the Power Switch.
5. Make sure the Power Switch is off when you take the loaf out.
6. When finished, turn off the Power Switch.

WARNING!
THE LAST LOAF CAN BE SLICED EASILY. PLEASE DO NOT PUSH IT WITH A FINGER FROM THE CHUTE OR TAKE OUT THE LOAF FROM THE FRONT SIDE.

Blades Replacement

When the Bread Slicer slices the bread slowly, it indicates that the blades are blunt and must change the new blades.
The steps of dismantling blades

1. Please take off the Front Cover and Top Cover.
2. Take down the Receiving Plate
3. Loosen the screws from Knife Frame.
4. Take out the Driving Rod Link so that can take down the Knife Frame.
5. Press Spring to take out the Blades.

The steps of installing blades

1. Please press the Spring to put the Blade on the Knife Frame.
2. Put the Knife Frame into the machine and insert the Driving Rod Link.
3. Lock the screws on the Knife Frame.
4. Put the Receiving Plate into the machine.
5. Install the Front Cover and Top Cover.

The Parts List

Assembly Drawing

Electrical Drawing

WARRANTY

TERMS AND CONDITIONS

• This Warranty becomes effective from the date of delivery.
• Warranty claims may be made by telephone, letter, email, or fax.
• However, all verbal claims must be confirmed in writing. I.B.E. reserves the right to require the return of all claimed defective parts, cost of return freight is not included.
• I.B.E. will ship the part(s) in an expeditious manner as requested.
• Mechanical and Electrical parts are warranted for a period of 12 months from the date of delivery
• During the first 12 months, I.B.E. will reimburse the Authorized Agent or Purchaser for the cost of reasonable labor during normal working hours, 8.00 a.m. – 5.00 p.m., to remove the failed parts) and install the replacements). After 12 months all charges will be the Purchaser’s responsibility.
• After the initial 12-month warranty, any replacement parts are warranted for 3 months excluding labor.
• This Warranty may not be changed or modified and is not subject to any other
• Warranty expressed or implied by any other Agent, Dealer, or Distributor unless approved in writing by I.B.E. in advance of any claim being filed. This Warranty gives you specific legal rights which vary from State to State.
• I.B.E. reserves the right to make the final decision on all Warranty coverage questions.
• The decision of the Company is final.

WHAT IS COVERED

• Parts that fail due to defects in material workmanship.
• Parts that fail due to faulty assembly by I.B.E.
• Parts that fail due to improper set-up by I.B.E.

WHAT IS NOT COVERED

• Parts that fail due to improper usage or overloading of the machine.
• Parts that fail due to lack of maintenance.
• Parts that fail due to abuse, misuse, or modification.
• Mixer attachments – Bowl, whisk, beater, and/or hook.
• Normal wear parts, such as conveyor belts, ‘v’ belts, ‘o’ rings, scrapers, and slicer blades. The Warranty on these parts is, that they will be in satisfactory operating condition at the time of delivery and initial start-up.
• Claims on such parts must be made immediately.
• Loss of time, potential revenue, and/or profits.
• Personal injury or property damage resulting from the operation of the machine.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>