ideal lux SP8 Gioconda Pendant Light Lamp Instruction Manual

ideal lux SP8 Gioconda Pendant Light Lamp

Product Information

• Model: Gioconda SP8
• Maximum Wattage: E14 max 8 x 40W
• Power Supply: 220-240V, 50/60Hz
• Color Options: ARGENTO (Silver), ORO (Gold)
• Manufacturer: IDEAL LUX srl
• Country of Origin: Italy

Product Usage Instructions

Installation:
The installation of this lighting fixture should be carried out by a qualified electrician.

Safety Instructions:

• Complies with European safety standards EN 60.598-1.
• Always disconnect the power supply before installation or maintenance.
• Use appropriate fixtures and accessories for mounting.

Maintenance:
If the lamp does not turn on, replace the fuse.

Electrical Safety Classes:

• Class I: Safety ensured by main insulation and grounding connection to the metal structure of the lamp.
• Class II: Safety ensured by double insulation or reinforced insulation, no grounding required.
• Class III: Safety ensured by low voltage supply (below 50 Volts), no grounding required.

Protection Ratings:

• IP20: Not protected.
• IP25: Protected against solid objects over 50 mm in diameter.
• IP26: Protected against solid objects over 12 mm in diameter.
• IP27: Protected against solid objects over 2.5 mm in diameter.
• IP28: Protected against solid objects over 1 mm in diameter.
• IP29: Protected against dust.
• IP30: Protected against dust.

Frequently Asked Questions

Q: Can the LED light source be replaced?

A: The LED light source in this fixture is not replaceable. Do not disassemble the fixture.

Q: What should I do if the lamp does not turn on?

A: Replace the fuse in the lamp if it fails to turn on.

Q: Do I need to ground the lamp during installation?

A: The grounding requirements depend on the electrical safety class of the fixture. Follow the instructions for your specific model.

Specification

Suspension lamp

• E14 max 8 x 40W / 220~240V 50/60Hz
  • 8021696044934 ARGENTO
  • 8021696060514 ORO

Dimension

SAFETY INSTRUCTIONS

1. This fitting is produced and tested by the strictest European safety standards (EN 60.598-1).
2. This fitting cannot be disposed of as household waste. For disposal information ask the local authorities about how to collect it.
3. As indicated by specific regulations, the lighting fitting should be installed by a qualified electrician.
4. If the external wire is damaged it has to be replaced exclusively by the manufacturer, distributor, or by a qualified electrician.
5. Always isolate power before commencing installation, maintenance, or repair.
6. The luminaire contains certain parts which can be very hot.
7. Each material requires specific mounting accessories. Use screws and wall plugs suitable for the material to which they are fastened. Those included may be unsuitable.
8. Always tighten the screws firmly to avoid contact problems.
9. This fitting should only be installed indoors.
10. Luminaires are not suitable for recessed on normally flammable surfaces.
11. Luminaire is not suitable for direct mounting on normal flammable surfaces.
12. This fitting is only suitable for fixing the ceiling.
13. This fitting is only suitable for fixing the wall.
14. The weight of the lamp has to be supported by the chain. Adjust the length of the electric wire so that it is longer than the chain.
15. Only use lamps that do not exceed the maximum specified wattage.
16. Always observe the minimum distance between the lamp and the surface being lit, as shown in the icon. The lamp can cause a fire if the minimum distance is not observed.
17. Auto-protected bulb. Only use bulbs marked with this symbol. Halogen bulbs get very hot. Wait until they cool down before replacing them.
18. Cracked or broken safety glass has to be replaced immediately. Use only manufacturer-approved parts complying with regulations.
19. Light source with not-substitutable light emitting diode (LED). Do not disassemble the product since the diodes can damage the eyes. Do not immerse in water. Wipe with a damp cloth. Do not use solvents or strong detergents.
20. This fitting is equipped with a fuse. If the lamp is out of order, replace the internal fuse.
21. Class I Electrical safety is guaranteed by the main insulation and an additional protective conductor (earthing) connected to the metal frame of the lamp. Earthing is obligatory.
22. Class I| Electrical safety guaranteed by the main insulation and double or reinforced insulation. Earthing is not necessary.
23. Class II Electrical safety is guaranteed by a very low power supply (less than 50 Volts). Earthing excluded.
24. Not protected.
25. Protected against solid objects greater than 50 mm.
26. Protected against solid objects greater than 12 mm.
27. Protected against solid objects greater than 2,5 mm.
28. Protected against solid objects greater than 1mm.
29. Dust protected.
30. Protected against dust infiltration.
31. Not protected.
32. Protected against vertically falling water drops.
33. Protected against water drops falling with a maximum angle of 15° to the vertical axis.
34. Protected against rain.
35. Protected against splashing water.
36. Protected against water jets.
37. Protected against strong water jets.
38. Protected against temporary immersion.
39. Protected against prolonged immersion.
40. Luminaire is not suitable for covering with thermally insulating material.
41. Caution, risk of electric shock.
42. Do not stare at the operating light source.

ASSEMBLY INSTRUCTIONS

THE SAFETY AND RELIABILITY ARE GUARANTEED ONLY WHEN INSTALLATION INSTRUCTIONS ARE PROPERLY FOLLOWED. PLEASE KEEP THIS INSTRUCTION SHEET FOR FUTURE REFERENCE.

Contact Information

• IDEAL LUX s.r.l.
  Via Taglio Destro 32 30035 Mirano (VE) Italy

• www.ideal-lux.com.

IDEAL LUX Warehouse
Via delle Industrie, 8/D 30036 Santa Maria di Sala (Venezia) 8.00 – 12.00/13.30 – 17.00.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>