MICSIU A19007 Outdoor Wall Mount Light Fixture Exterior Sconces Installation Guide

MICSIU A19007 Outdoor Wall Mount Light Fixture Exterior Sconces

Product Information

Specifications

• Model: A19007A19008A20008A20009A20010A20011
• Required Supply Circuit: 120V, 60Hz
• Bulb Type: 1E26100W Max (Compatible Bulb Type, NOT Included)
• Most Suggested Bulb Type: 8W LED ST58 or A19 bulb

Components Included in the Package

• Fixture with hardwares and glass
• Parts included in parts bag
• Parts X 2 for 2 pack item

Assembly & Installation Steps

1. Open the box from top, take out all the components, parts bag, and manual from the box carefully.
2. Check all the components against the parts list. Make sure to get each part on the list.
3. If any parts are missing or if there is glass damage, please contact the manufacturer at [email protected] to get a replacement.
4. In case of damaged glass, loosen the screws (N) using a screwdriver to replace the glass panels (L).
5. Open the clips to release the glasses.
6. Replace the damaged glasses and then bend the clips again to fix the glass in position.
7. Fasten the screws to assemble the fixture frame onto the top hood.

MODEL: A19007, A19008, A20008, A20009, A20010, A20011

IMPORTANT SAFETY INSTRUCTIONS

• Warning: If any special control devices are used with this fixture, follow the instructions carefully to assure full compliance with N.E.C. requirements. If there are any questions, contact a qualified electric contractor.
• Warning: This product can expose you to chemicals including lead, which is known to the State of California, to cause cancer or birth defects or other reproductive harm. For more information, please go to www.P65Warnings.ca.gov.
• Caution: Electrician installation highly recommended. All glass is fragile, use care when handling glass component(s) and or lamp(s). Read instructions carefully and turn electricity off at the main circuit breaker panel before beginning installation.

Important Notice

• This is a generic instruction sheet used for various fixtures.
• The finish, numbers of heads/arms, and style of fixture / glass / shade / diffuser may vary.

COMPONENTS INCLUDED IN THE PACKAGE

ASSEMBLY & INSTALLATION STEPS

1. Open the box from top, take out all the components, parts bag and manual from the box carefully.
2. Check all the components against the parts list. Make sure get each parts on list. If any parts missing and glass damage, please contact manufacturer at: [email protected] to get a replacement.
   Parts are NOT included for which is shown as 0 under QTY.

PARTS LIST                (Parts QTY X 2 for 2 pack item)

Part Name| QTY| Code|  | Part Name| QTY| Code
Junction Box| 0| A| Wire Nut| 3| I
Leading Wire| 0| B| Wire| 2| J
(1.25″) Mounting Screw| 2| C| Socket| 1| K
Cross Bar Mounting Bracket| 1| D| Glass| 4| L
Stud| 2| E| Light Bulb| 0| M
Back Plate| 1| F| Screw| 2| N
Washer| 2| G|  |  |
Cap Nut| 2| H|  |  |
3. Refer to the illustration while doing assembly and follow the steps as below:

1. Screw on the bulb (M) onto socket (K) before installation.
2. Thread two studs (E) onto the mounting bracket (D) at proper position.
3. Attach the mounting bracket (D) to the junction box (A) by two mounting screws (C). Adjust the mounting bracket to make the fixture installed at a horizental level.
4. Connect wires according to the wiring diagram as below.
5. Attach the backplate (F) to two studs (E) and fix with two washers (G) and cap nuts (H).
   In a case of damaged glass, loose the screws(N) by a screw driver to replace the glass panels(L), open the clips to release the glasses. Replace the damaged glasses then bent the clips again to fix the glass in position, fasten the screws to assemble the fixture frame onto the top hood.

Illustration of assembly and wiring

Missing parts? Glass damage? Any questions?
Please email us at: [email protected]
We are always here to help you fix the problems you are facing.

References

• P65Warnings.ca.gov

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>