LAMAX S11600 350W Electric Scooter User Manual

: June 14, 2024
: LAMAX

Table of Contents

BOX CONTENTS
PRODUCT DESCRIPTION
ASSEMBLING AND FOLDING THE SCOOTER
MULTI FUNCTION DISPLAY/CONTROL
RIDING THE SCOOTER
APPLICATION
SPECIFICATIONS
CHARGING THE BATTERY
BATTERY SAFETY PRECAUTIONS
SERVICING, MAINTENANCE AND STORAGE
SAFETY PRECAUTIONS
FURTHER INFORMATION
Documents / Resources

LAMAX S11600 350W Electric Scooter User Manual

BOX CONTENTS

a) LAMAX E-Scooter S11600

b) Charger

c) Allen key

d) Screw (4×) to fasten the handlebars

e) Instructions

PRODUCT DESCRIPTION

Product Overview

a) Handlebars
b) LED headlight
c) Brake lever
d) Handlebar post
e) Folding mechanism with lock
f) 350 W motor/front 10“ tubeless tyre
g) Deck
h) Catch (to anchor scooter when folded)
i) Rear brake light
j) Rear 10“ tubeless tyre
k) Rear disc brake
l) Kickstand
m) LED side lights
n) Multifunction display
o) Bell
p) Throttle lever
q) Power input
r) Hook

ASSEMBLING AND FOLDING THE SCOOTER

a) Assembly (we recommend that two people do this)

Carefully remove the scooter from the box, place it on the ground and flip out the kickstand. Move the handlebar post to an upright position and fasten it by pushing the folding mechanism towards the handlebar post.
Connect both cables to the handlebars so that the arrows on the cables face each other, and then slide the handlebars onto the post.
Finally, fasten both parts using the four screws and the Allen key supplied.

b) Folding

Push the lock of the folding mechanism upwards and release it by pulling it away from the handlebar post.
Fold the handlebar post towards the rear fender.
Then clip the handlebar hook to the catch on the rear fender.

MULTI FUNCTION DISPLAY/CONTROL

Power

Press the POWER button to turn the scooter on.
Hold the POWER button for five seconds to turn the scooter off.

LED headlight

When the scooter is switched on, press the POWER button to turn the LED headlight and LED side lights on/off. The LED headlight must always be switched on when riding in reduced visibility and at night.

Speed modes

Double-tap to toggle between riding modes .
Red = sport mode
Green = ECO (power saving) mode
Selecting ECO mode improves range and reduces battery load.

Battery indicator

To maximize battery life, we recommend riding the scooter until the battery is completely discharged.

Battery indicator	Battery capacity in%
80–100%
60–80%
40–60%
20–40%
0–20%

Bluetooth

The scooter’s Bluetooth is always on.
A lit icon indicates it is connected to your device.

RIDING THE SCOOTER

Warning: There is a risk of falling and possible injury during every scooter ride, so always wear a helmet and knee and elbow protectors. Always check the functionality of the brakes, lights and that the folding mechanism lock is properly secured to the handlebar post before riding.

Recommended rider requirements:

Rider height: 130–190 cm
Rider weight: 30–120 kg
Rider age: 14–60 years
Children can only operate or otherwise handle the scooter under the supervision of a qualified adult. The same applies to those with reduced mobility.

a) Before riding, fully charge the scooter.
b) Turn the scooter on by pressing the POWER button and hold the handlebars.
c) Keep both hands on the handlebars at all times when riding.
d) Once the scooter is on, put one foot on the scooter deck and kick off with the other foot. After reaching a speed of 5 km/h, put the other foot on the deck to improve stability and press the throttle lever (accelerator). You can now regulate the speed of the scooter by pressing or releasing the throttle lever.
e) Keep both hands on the handlebars and both feet on the scooter deck throughout the ride.
f) To stop, release the throttle lever and gently press the brake lever on the handlebars. Never brake with your foot, never use the rear fender as a brake or step on it while riding.
g) When the ride is complete, hold down the POWER button for 5 seconds and charge the scooter to half capacity.

APPLICATION

Running the app

a) Scan the QR code or go to
https://www.lamax-electronics.com/e-scooter-s11600/app
b) Install the app on your smart device.
c) Turn on the scooter.
d) Turn on Bluetooth on your device and search for LAMAX E-Scooter S11600.
e) After connecting to the scooter, launch the application.

Main menu/quick controls

a) Current speed
b) Settings menu
c) Select riding mode
d) Lock
e) LED headlight
f) Cruise control
g) Bluetooth
h) Information
i) Battery capacity
j) Maximum set speed

Settings menu
a) Speed units – allows you to set units in KMPH or MPH.
b) Cruise control – turns cruise control on/off.
c) Cruise control speed setting – after riding for 10 seconds above the preset speed, the scooter beeps, telling you that cruise control is now active. It is no longer necessary to press the throttle lever to continue moving. Braking or pressing the throttle lever will turn off cruise control. Using cruise control is ideal for longer trips on the flat.
d) Battery capacity – select the exact or closest battery capacity here. The LAMAX E Scooter S11600 has an 11.6 Ah battery.
e) Riding mode – selects the riding mode – see Section 4.
f) Speed limit – sets the speed limit for the selected mode.

SPECIFICATIONS

Weight	15 kg
Maximum load capacity	120 kg
Top speed	25 km/h
Maximum range	30–40 km
Maximum pitch angle	15°
Battery	Lithium, 11.6 Ah, 36 V
Motor	350 W
Dimensions (folded)	115×43×51 cm
Dimensions (unfolded)	115×43×120 cm
Deck height	17 cm
Wheels	10“ (tubeless tyres)

Battery specifications

Battery type	Lithium batteries
Charging time	5–6 hours
Voltage	36 V
Battery capacity	11600 mAh
Operating temperature	5 °C – 50 °C
Charging temperature	0 °C – 40 °C
Storage temperature	5 °C – 25 °C
Storage humidity	5 % – 85 %, non-condensing

Power supply specification

Input voltage	100–240 V
Input AC frequency	50–60 Hz
Output voltage	42 V
Output current	2 A
Output power	84 W
Average active efficiency	88,34%
Efficiency at low load (10 %)	83,2%
No-load power consumption	0,21 W

CHARGING THE BATTERY

The battery is the most important part of the scooter. Electric scooters are equipped with lithium-ion cells. These batteries are able to provide better functionality and a longer lifespan than lead batteries. They are lightweight and powerful. However, these batteries do also have a life cycle. To maximize their lifespan, it is important to regularly take care of the batteries and charge the battery to 100% every few days or after each ride.

To charge the battery, only use the original charger from the manufacturer that comes supplied with the scooter.
If the battery indicator shows low battery, plug the scooter into the charger.
Always make sure that the charging port is clean and dry before charging. If the scooter is not connected to the charger, the power input must always be covered with the rubber cap to prevent dust or other dirt from entering the inlet.
Connect the power cord to the charger and then plug the charger into an electrical socket, making sure that the light on the charger is GREEN.
Insert the end of the charger into the power input on the scooter. The charger light should turn RED when charging. When the light turns GREEN, the scooter is fully charged. It takes approximately 5–6 hours to fully charge.
After charging the scooter, disconnect the charger from the power socket and the power cable from the scooter.
Do not leave the scooter connected to the charger longer than necessary to fully charge. Never leave the scooter connected to the charger unattended.

BATTERY SAFETY PRECAUTIONS

Fully charge the battery before using it for the first time.
Charge regularly, after every ride.
Never let the battery drain completely!
Use standard charging cables, otherwise the device may be damaged.
Operating temperature can affect the overall battery life.
Under no circumstances should you connect damaged or swollen batteries to the charger. Never use batteries in this condition, there is a risk of explosion.
Do not use a damaged power adapter or charger.
Charge at room temperature, never charge at below 0°C or above 40°C.
Be careful not to drop, puncture, or otherwise damage the battery. Never attempt to repair a damaged battery.
Do not expose the charger or battery to moisture, water, rain, snow or any kind of spray.
Do not leave the battery in a vehicle, do not expose to sunlight or place near heat sources. Powerful light or high temperatures can damage the battery.
Never leave the batteries unattended while charging. A short circuit or accidental overcharging can cause the aggressive chemicals to leak, explode or subsequent fire!
If the battery overheats while charging, unplug the battery immediately.
Do not place the charger or battery on or near flammable objects when charging. Keep away from curtains, carpets, tablecloths, etc.
Keep the battery out of reach of children and animals.
Never disassemble the charger or battery.
If the battery is integrated, never disassemble the device unless otherwise specified. Any such attempt is a risk and may result in damage to the product and subsequent loss of warranty.
Do not dispose of worn or damaged batteries in a waste bin, fire or heating system. Hand them in at hazardous waste collection plants.
If you do not comply with this policy, you assume full responsibility for any damages incurred.

SERVICING, MAINTENANCE AND STORAGE

The scooter needs regular inspection and maintenance just like a bicycle or motorcycle. Always make sure that the scooter is switched off and the power cord is disconnected before performing the following operations.

Scooter inspection and cleaning

Regularly check the frame and tyres for damage or excessive wear. If a tyre is excessively worn, it should be changed. Do not use water or other liquids or detergents for cleaning. Dampen a clean cloth with clean soapy water and apply to the scooter frame, then rinse the cloth thoroughly and wipe the scooter down. When cleaning, make sure water does not get into the battery cover, power input, display, or tyres.

Maintenance and servicing

The scooter requires regular maintenance and servicing similar to a bicycle. We recommending performing a service inspection at least once a year.

Storing the scooter

Fully charge the battery before storage. If you are storing the scooter for an extended period, charge the battery to half capacity every 30 days. Not doing so is likely to result in equipment failure which is not covered under warranty.
If the storage temperature is less than 0°, do not charge the scooter immediately. Before charging, you must place the scooter in a warmer environment (5°C–40°C) for at least 2 hours.

To prevent dust from entering the scooter, pack it in the original box and seal with tape. Store the scooter indoors, in a dry place and at the correct storage temperature.

SAFETY PRECAUTIONS

Packaging contains small pieces, that can be dangerous for children. Store the product always out of reach of children. Bags or many of the pieces containing may cause suffocation after swallowing.
Failure to comply with the basic instructions and any of the following safety measures may result in damage to the scooter, loss of the manufacturer‘s warranty, other property damage, serious injury and even death. Only use original accessories, including the battery. If you use incompatible accessories, you risk losing your warranty and may damage your device.
Respect your surroundings and comply with the applicable regulations and laws of the state in which you are located. The user must comply with the applicable local traffic regulations when riding an electric scooter. In the case of illegal use on public roads, including cycle paths, the user is exposed to the risk of a fine or even prosecution for causing a traffic accident.
Read the instructions carefully.
The scooter is designed for only one person.
Before each use, check the technical condition of the scooter.
Always check the brakes and tyre condition before driving. Make sure that there is nothing obstructing the wheels!
Disc brakes get hot when braking, so do not touch the disc or shoes, especially shortly after when they are used.
When riding a scooter, wear all appropriate safety and protective equipment (especially ahelmet).
Never drive without holding the handlebars.
When riding a scooter, wear sturdy, closed shoes.
Look where you‘re going and pay attention to road conditions, people, places, property and objects around you.
Operate the scooter with respect to pedestrians, cars and cyclists.
Pay full attention to riding the scooter. Don‘t use the scooter when you‘re talking, on the phone, texting, or otherwise handling your phone or any other device that may distract you.
Do not ride a scooter unless permitted at the location.
Always follow local ordinances and regulations.
Do not drive on 1st and 2nd class roads for motor vehicles or motorways.
Do not drive in places with a large number of pedestrians.
Do not remove scooter signalling elements such as reflective stickers or LED lighting.
Never drive in the rain.
Do not hang bags, backpacks or other objects on the scooter.
As a matter of principle, do not attempt to disassemble, repair or modify the scooter in any way. Disassembly, modification or any attempt at repair will void the warranty and may result in damage to the device or even injury or property damage.
Do not operate the scooter under the influence of alcohol, drugs or other addictive substances and substances that affect the ability to coordinate and react.
Do not use the scooter if you are tired or sleepy.
Use your judgment to avoid dangerous situations with the scooter.
Do not ride your scooter on ramps or at a skate park, an empty swimming pool or places for skateboarding. Do not go down railings, jump or attempt to go over obstacles on the scooter.
Do not turn sharply, especially at high speeds.
Do not drive to or near puddles of water, mud, sand, stones, gravel, or in rough and rugged terrain. This risks damaging the scooter. If you encounter an uneven pavement, lift the scooter and go over the obstacle.
Do not drive in bad weather: snow, rain, hail, icy roads or extreme heat. On damp or wet roads, it can be easier to skid, fall or lose balance.
Do not drive near swimming pools or other large bodies of water.
Bend your knees when riding on bumpy or uneven surfaces to absorb the bumps and vibrations and help you maintain stability. If you are not sure if you can safely ride on a particular terrain, get off the scooter and guide it on foot.
Do not attempt to ride over bumps or objects higher than 1.5 cm.
If the consumer attempts to alter the software in any way, the warranty is voided.
Handle the scooter carefully if you are indoors.
Do not ride hills steeper than 15° on the scooter (when climbing sharply always help yourself by kicking).
The scooter is intended for use by one person, NEVER try to ride it with two people.
Women should not operate the scooter if they are pregnant.
Children can only operate or handle the scooter under the supervision of a qualified adult. The same applies to people with reduced mobility.
At higher speeds, always take into account the longer braking distance.
Do not jump off the scooter while riding.
Do not jump on the scooter while riding.
Do not attempt stunts or tricks with the scooter.
Do not use the scooter outside of designated areas.
Do not exceed the maximum load capacity of the scooter.
Avoid riding near hazardous or flammable substances.
In ideal conditions and with a fully charged battery, the scooter can travel a distance of up to 40 km.
Factors that affect the maximum range of the scooter: terrain, rider weight, ambient temperature, weather conditions and riding style.

FURTHER INFORMATION

For households: The symbol ( ) on the product or in the accompanying documentation means that used electrical and electronic products must not be disposed of with your other household waste. In order to dispose of the product properly, please return it to a designated collection point, where it will be accepted free of charge. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences to the environment and for human health, which could otherwise be caused by inappropriate waste handling of this product. Contact your local authority or the nearest collection point for further details. Improper disposal of this type of waste may result in penalties in accordance with national regulations. Information for users on disposal of electrical and electronic equipment (corporate and business use): For proper disposal of electrical and electronic equipment, please contact your dealer or supplier for detailed information. Information for users on disposal of electrical and electronic equipment in other countries outside the European Union: The above symbol (crossed-out wheelie) is only valid in European Union countries. For proper disposal of electrical and electronic equipment, request detailed information from your authorities or equipment dealer. Everything is expressed by the crossed-out wheelie bin symbol on the product, packaging, or printed materials.
Apply for warranty repairs of the device at your dealer. In case of technical problems and questions, contact your dealer, who will inform you about the next steps. Follow the rules for working with electrical equipment. The user is not authorized to disassemble the device or replace any part of it. There is a risk of electric shock when opening or removing covers. You also run the risk of electric shock if the device is incorrectly assembled and reconnected.

The warranty period for the product is 24 months, unless otherwise stated. The warranty does not cover damage caused by non-standard use, mechanical damage, exposure to aggressive conditions, handling contrary to the manual and normal wear and tear. The warranty period for the battery is 24 months and for its capacity 6 months.

The manufacturer, importer or distributor is not liable for any damage caused by assembly or improper use of the product.

Declaration of Conformity
elem6 s.r.o., hereby declares that all LAMAX devices are in compliance with the essential requirements and other relevant provisions of directives 2014/53/EU, 2014/30/EU, 2014/35/EU and 2006/42/EC. The products are intended for sale without restrictions in Germany, the Czech
Republic, Slovakia, Poland, Hungary and other EU member states. The warranty period for the products is 24 months, unless otherwise stated. The warranty period for the battery is 24 months, and for its capacity 6 months. The declaration of conformity can be downloaded from the website
www.lamax-electronics.com/support/doc.

Frequency band(s) in which the radio equipment operates: 2.4 GHz

Manufacturer:
elem6 s.r.o., Braškovská 308/15, 16100 Prague 6
www.lamax-electronics.com

Print errors and changes to the manual reserved.
Symbols