KidKraft 9513 Cozy Escape Playhouse Installation Guide

KidKraft 9513 Cozy Escape Playhouse

Product Information

Specifications

• Door Bumper: 1 x S0 #8 x 7/8 Truss Screw
• Hinges: 3 x S37 #7 x 5/8 Pan Screws per hinge
• Magnetic Catch: 1 x Magnetic Catch, 2 x S38 #7 x 1-1/8 Pan Screws
• Table Top Short: 2 x 9516 Table Top Short, 4 x S11 #8 x 2 Wood Screws
• Table Top: 1 x 9515 Table Top, 4 x S11 #8 x 2 Wood Screws

Product Usage Instructions

Step 5: Door Assembly Part 2

• E: Install 1 Door Bumper using 1 (S0) #8 x 7/8 Truss Screw. (Fig. 5.4)
• F: In the opening for the door put Dutch Door Assembly in place, measuring to ensure that it is 5/8 (15.9mm) up from the bottom frame (fig. 5.5). Attach hinges to the Wall Frame using 3 (S37) #7 x 5/8 Pan Screws per hinge as shown in fig. 5.6 and 5.5.

Step 5: Door Assembly Part 3

• G: In the notched-out opening of the (9513) Door Stop attach the Magnetic Catch using 2 (S38) #7 x 1-1/8 Pan Screws. (fig. 5.7)
• H: On the inside of the assembly, attach the (1913) Door Stop to (9263) Folding Panel Assembly Right A with 2 (S11) #8 x 2 Wood Screws, making sure (1913) Door Stop overhangs by 1-1/4 (32mm) and is in position to receive the Catch Plate. (fig. 5.8, 5.9)

Step 6: Attach Wall Tops Part 1

• A: From outside of the assembly, place 1 (9516) Table Top Short in the narrow openings of (9263) Folding Panel Assembly Right A and (9265) Folding Panel Assembly Left B. Attach with 2 (S11) #8 x 2 Wood Screws per board. (fig 6.1)

Step 6: Attach Wall Tops Part 2

• B: Place (9515) Table Top into the opening on the back of (9265) Folding Panel Assembly Left B and attach using 4 (S11) #8 x 2 Wood Screws. (fig. 6.2)

Step 6: Attach Wall Tops Part 3

• C: From inside the assembly, place 1 (9515) Table Top into the end wall opening of (9264) Folding Panel Assembly Left A and (9266) Folding Panel Assembly Right B. Attach using 4 (S11) #8 x 2 Wood Screws as shown in fig. 6.3.

Step 6: Attach Wall Tops Part 4

• D: From outside of the assembly, place 1 (9515) Table Top into the front opening of (9266) Folding Panel Assembly Right B. Attach using 4 (S11) #8 x 2 Wood Screws fig. 6.4.

FAQ

Q: How should I attach the hinges in Step 5?

A: Attach hinges to the Wall Frame using 3 (S37) #7 x 5/8 Pan Screws per hinge as shown in Fig. 5.6 and 5.5.

Q: What should I be cautious about when attaching the Magnetic Catch in Step 5?

A: Use a hand-held screwdriver and DO NOT over-tighten when attaching the Magnetic Catch using 2 (S38) #7 x 1-1/8 Pan Screws.

INSTALLATION STEP

Step 5: Door Assembly Part 2

• E: Install 1 Door Bumper using 1 (S0) #8 x 7/8” Truss Screw. (Fig. 5.4)
• F: In the opening for the door put Dutch Door Assembly in place, measuring to ensure that it is 5/8” (15 .9mm) up from the bottom frame (fig. 5.5). Attach hinges to the Wall Frame using 3 (S37) #7 x 5/8” Pan Screws per hinge as shown in fig. 5.6 and 5.5.

Step 5: Door Assembly Part 3

• G: In the notched-out opening of the (9513) Door Stop attach the Magnetic Catch using 2 (S38) #7 x 1-1/8” Pan Screws. (fig. 5.7)
• Important: Use a handheld screwdriver and DO NOT over-tighten.
• H : On the inside of the assembly, attach the (1913) Door Stop to (9263) Folding Panel Assembly Right A with 2 (S11) #8 x 2” Wood Screws, making sure (1913) Door Stop overhangs by 1-1/4” (32mm) and is in position to receive the Catch Plate. (fig. 5.8 , 5.9)

Step 6: Attach Wall Tops Part 1

• A: From outside of the assembly, place 1 (9516) Table Top Short in the narrow openings of (9263) Folding Panel Assembly Right A and (9265) Folding Panel Assembly Left B. Attach with 2 (S11) #8 x 2” Wood Screws per board. (fig 6.1)

Step 6: Attach Wall Tops Part 2

• B: Place (9515) Table Top into the opening on the back of (9265) Folding Panel Assembly Left B and attach using 4 (S11) #8 x 2” Wood Screws. (fig. 6.2)

Step 6: Attach Wall Tops Part 3

• C: From inside the assembly, place 1 (9515) Table Top into the end wall opening of (9264) Folding Panel Assembly Left A and (9266) Folding Panel Assembly Right B. Attach using 4 (S11) #8 x 2” Wood Screws as shown in fig. 6.3.

Step 6: Attach Wall Tops Part 4

• D: From outside of the assembly, place 1 (9515) Table Top into the front opening of (9266) Folding Panel Assembly Right B. Attach using 4 (S11) #8 x 2” Wood Screws fig. 6.4.

Step 7: Counter Assembly Part 1

• A: Flush to each end and the bottom of (9473) Counter Back attach 1 (9471) Counter Joist per end with 1 (S20) #8 x 1-3/8” Wood Screw per joist. Notice the holes at the top of (9473) Counter Back. (fig. 7.1 & 7.2)
• B: Place the remaining 2 (9471) Counter Joists centered over the pilot holes in the middle of the (7613) Counter Back and flush to the bottom of the board. Attach in the bottom holes using 1 (S20) #8 x 1-3/8” Wood Screw per joist. (fig. 7.1 & 7.2).
• C: Place (9472) Counter Front against (9471) Counter Joists so the ends are flush and the (9471) Counter Joists are centered over the pilot holes. Measure 5/8” (16mm) down from the top of the (9472) Counter Front on both ends and attach to the (9471)
• Counter Joists with 4 (S20) #8 x 1-3/8” Wood Screws. (fig. 7.1 & 7.2)

Step 7: Counter Assembly Part 2

• D: Place 1 (9470) Counter Brace tight to the bottom of each outside (9471) Counter Joist, tight to (9472) Counter Front and attach using 1 (S3) #8 x 2-1/2” Wood Screw per brace. ( fig 7.3 & 7.4 & 7.5)

Step 8: Attach Counter Assembly Part 1

• A: On the inside of the assembly place the Counter Assembly against the Cafe Wall flush with the opening. (fig 8.1) B: Attach (9473) Counter Back to Cafe Wall with 4 (S20) #8 x 1-3/8” Wood Screws. (fig 8.1)
• C: Attach both (9470) Counter Braces to Cafe Wall with 1 (S11) #8 x 2” Wood Screw per brace. (fig 8.1)

Step 8: Attach Counter Assembly Part 2

• D: Tight to (9473) Counter Back attach (9474) Counter Top to each (9471) Counter Joist with 4 (S38) #7 x 1-1/8” Pan Screws. (fig. 8.2)
• E: Tight to (9474) Counter Top and flush to the outside edges of the outer (9471) Counter Joists attach 1 (9476) Counter Side per joist with 3 (S38) #7 x 1-1/8” Pan Screws per board. (fig. 8.2)
• F: Tight to (9474) Counter Top and centered over the middle 2 (9471) Counter Joists with ends flush to the outside edges, attach 2 (9475) Counter Mid Tops with 4 (S38) #7 x 1-1/8” Pan Screws per board. (fig. 8.2)

Step 8: Attach Counter Assembly Part 3

• G: Place Faucet and 2 Sink Knobs in the opening of the Sink and attach Sink Knobs with included hardware. (fig. 8.3) Important: Use a handheld screwdriver and DO NOT over-tighten.

Step 8: Attach Counter Assembly Part 4

• H: Place the Sink and Stove in the openings of the Counter Assembly then attach 4 Mount Clips with included hardware to the bottom of the Sink and Stove to secure them in place. (fig. 8.4 and 8.5)
• Important: Use a handheld screwdriver and DO NOT over-tighten.
• Note: To remove the Sink or Stove loosen the screw 1/4 turn then twist Mount Clips

Step 9: Attach Utensil Shelf

• A : From inside the assembly attach 1 Utensil Shelf with 2 (S0) #8 x 7/8” Truss Screws as shown in fig. 9.1 & 9.2.
• B: Attact the Pot, Pan, and Spatula to the Utensil Shelf. (fig. 9.2)

Step 10: Crowsnest Assembly

• A: Lay flat 2 (9494) Crowsnest Uprights taking note of the hole orientation. Place 2 (9499A) Crowsnest Bottoms over the top two sets of pre-drilled holes as shown in ( Fig.10.1).
• Attach using 2 (H3) 1/4 x 2-1/2” Hex Bolts (with flat washer, lock washer and t-nut) per board. (Fig. 10.1)
• B: Place (9499) Crowsnest Bottom over the bottom set of pre-drilled holes, and attach using 2 (H3) 1/4 x 2-1/2” Hex Bolts (with lock washer, flat washer, and t-nut). (Fig. 10.1)

Step 11: Attach Crowsnest Assembly Part 1

• A : With a helper, stand the Crowsnest Assembly upright, in front of the fort. Measure to make sure that there is a 21” space between the fort and the outside of (9499) Crowsnest Bottom, as shown in Fig. 11.3 & 11.4.
• B : Place 1 (9498) Crowsnest Short L across the opening from the fort to the (9494) Crowsnest Upright so that it’s flush to the outside edge and the bottom of the lower (9499) Crowsnest Bottom (fig. 11.2).
• Check to make sure the board is level, then attach using 4 (S3) #8 x 2- 1/2” Wood Screws. (fig. 11.1 & 11.2 )

Step 11: Attach Crowsnest Assembly Part 2

• A: In the openings between the (9499A) Crowsnest Bottoms and the fort, attach 2 (9496) Crowsnest Shorts using 5 (S3) #8 x 2- 1/2”
• Wood Screws per board, making sure that the boards are level and flush with the (9499A) Crowsnest Bottoms. (fig. 11.3 & 11.7)
• B : Repeat step A to install (9497) Crownest Short A in the location shown. (fig. 11.3 & 11.7)
• C : Place (9491) Ground Brace A across the bottom opening so that it’s flush with the front of (9494) Crowsnest Upright. Attach to the fort and the upright using 4 (S3) #8 x 2- 1/2” Wood Screws. (fig. 11.3 & 11.5)

Step 12: Attach Side Joist

• A: On the inside wall of the deck assembly, measure 5/8” down from the top of the door opening and place 1 (9466) Side Joist-2 along the length of the wall. Check to make sure Joist is level, then attach using 5 (S11) #8 x 2” Wood Screws. (Fig. 12.1 & 12.2)
• B: Measure 5/8” down from the top of (9499) Crowsnest Bottom and repeat Step A to install (9465) Side Joist-1 to the opposite side. (Fig. 12.1 & 12.2)

Step 13: Attach Floor Support

• A: Place 1 (9468) Floor Board Short tight to (9497) Crowsnest Short A and a second one tight to (9498) Crowsnest Short L.(fig.13.1 & 13.2 & 13.3)
• B: Place (9469) Floor Support tight to the bottom of each Floor Board, centered over the pilot holes on the (9497) Crowsnest End Short A and (9498) Crowsnest End Short I then attach with 2 (S4) #8 x 3” Wood Screws per end. (fig.13.1 & 13.2 & 13.3)
• C: Attach each (9468) Floor Board to (9466) Side Joist-2 and (9469) Floor Support using 5 (S20) #8 x 1-3/8” Wood Screws per board. (fig.13.2)

Step 14: Chair Assembly

• A : Place 1 (9488) Chair Top flush to the edges of 1 (9487) Chair Gusset A, making sure to note the hole orientation. Attach using 1 (S11) #8 x 2” Wood Screw. Repeat to install a second (9487) Chair Gusset on the opposite side. (Fig. 14.1)
• B: Install (9489) Chair Top A to (9487) Chair Gusset A’s using 2 (S11) #8 x 2” Wood Screws, making sure that the rounded edges are facing outwards. (Fig. 14.1)
• C: Place 1 (9486) Chair Gusset on each end of the (9487) Chair Gusset A’s making sure to note the hole orientation. Attach using 1 (S11) #8 x 2” Wood Screw per board. (Fig. 14.1)

Step 15: Attach Chair Assembly

• A : Measure 10-3/4” (27.3 cm) up from the top of the (9491) Ground Brace to the bottom of the (9488) Chair Top. (Fig. 15.2). Install Bench Assembly to the inside of the fort and the (9494)
• Crowsnest Upright as shown in (fig. 15.1 & 15.2 ) making sure that it is flush to the edge of the frame. Attach using 4 (S11) #8 x 2” Wood Screws per side.

Step 16: Attach Crowsnest Gusset

• A: On the underside of one end of the deck assembly, place 1 (9495) Crowsnest Gusset as shown in (fig.16.2). One end of the Gusset should be flat against (9465) Side Joist-1 and the other end should be flush with the front edge of (9494) Crowsnest Upright.
• Attach using 2 (S3) #8 x 2-1/2” Wood Screws. (fig.16.1 and 16.2)
• B: Repeat to install a second (9495) Crowsnest Gusset on the opposite side. (fig.16.1 and 16.2)

Step 17: Access Ladder Assembly Part 1

• A: Place (9478) Left Rail on one side of 4 (9480) Ladder Gap and (9479) Right Access on the other side with the grooves facing in. (fig. 17.1)
• B: Fit each (9480) Ladder Gap into grooves on both (9478) and (9479) Access rails, making sure the top edge of the (9480) Ladder Gap is flush with the front of the Access rails. (fig.17.1 and 17.2 & 17.3)
• C: Pre-drill pilot holes with a 1/8” drill bit and attach rails and Ladder Gap using 4 (S3) #8 x 2-1/2” Wood Screws per Ladder Gap. (fig.17.1 and 17.2)

Step 17: Access Ladder Assembly Part 2

• D: Place 1 (9481) RW-AL Support on the back of the ladder so that it sits flush to the top of the angle cut as shown in Fig. 17.5. Attach using 4 (S20) #8 x 1-3/8” Wood Screws. (Fig. 17.4 & 17.5)
• E: Flush to the top and edges of the (9478) and (9479) Rails, attach (9482) RW-AL A using 4 (S20) #8 x 1-3/8” Wood Screws. (Fig. 17.4 & 17.5)

Step 18: Attach Access Ladder Part 1

• A: Place the Ladder Assembly in the back opening of (9264) Folding Panel Assembly Left A.
• Make sure that the ladder is flush with the top of the floorboards and the outside edge of the panel, then attach using 2 (S20) #8 x 1- 3/8” Wood Screws.(Fig.18.1 & 18.2)

Step 18: Attach Access Ladder Part 2

• B : Place (9477) Supporting Diagonal so that the angled end is flush with the front edge of (9478) Left Rail and attach using 1 (H3) 1/4 x 2-1/4” Hex Bolt (with lock washer, flat washer and t-nut).
• Attach the opposite end of (9477) Supporting Diagonal to the fort using 2 (S11) #8 x 2” Wood Screws. (fig. 18.3)
• parts.kidkraft.com
• customerservice@kidkraft.com
• 1.800.933.0771
• 972.385.0100

Documents / Resources

| KidKraft 9513 Cozy Escape Playhouse [pdf] Installation Guide
9513 Cozy Escape Playhouse, 9513, Cozy Escape Playhouse, Escape Playhouse, Playhouse
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>