Enerlites 59302 120V Dimmer for Dimmable LED Instruction Manual
- June 14, 2024
- ENERLITES
Table of Contents
59302
120V Dimmer for Dimmable LED/ CFL
Incandescent / Halogen
(Single Pole/ 3-Way)
INSTALLATION INSTRUCTIONS
SPECIFICATIONS
Voltage ………………………………………………………………………………..120VAC, 60Hz
Incandescent/ Halogen……………………………………………………………………….700W
Dimmable LED and Dimmable CFL………………………………………………………150W
Operating Temperature……………………………………………………………….32°F-104°F
DESCRIPTION/ FEATURES
The 59302 is an Incandescent/Halogen and dimmable LED & CFL Dimmer. This Dimmer is designed to replace a standard light switch, dimmer, or a three-way lighting control (see 3-Way Wiring, Figure 2).
- Replaces current light switch using home’s existing wiring
- Slide dimmer and rocker switch turns lights on to a preset level
- Provides wider dimming range for dimmable LED and CFL bulbs than standard incandescent dimmers
- Suitable for multi-gang installations
- Dim lighting for increased energy savings
- Adjustable sensitivity levels on the control slider.
- Designed for compatibility with most high efficiency light bulbs.
WARNING
Turn the POWER OFF at the circuit breaker before installing the Dimmer
Read and understand these instructions before installing. This device is
intended for installation in accordance with the National Electric Code and
local regulations. It is recommended that a qualified electrician performs
this installation. Make sure to turn off the circuit breaker or fuse(s) and
make sure power is off before wiring the device.
Use copper wire only
NOTES:
The dimmer can be used as a Single Pole or 3-way switch.
Only one dimmer is needed for each 3-way application.
For use with incandescent, halogen, dimmable CFL and LED lights.
WIRING DIRECTIONS
-
Connect the HOT wire to the BLACK wire on the switch
-
Connect the load wire to the uninsulated RED wire on the switch
a. If using switch as 3-way, remove insulating label from red
wire and connect EACH RED wire to separate
TRAVELER wires. -
Connect GROUND wire to GREEN wire on the switch.
-
Mount the dimmer to the box with “UP” indicator pointing up.
-
Turn on Circuit Breaker
Single-Pole Wiring
3-Way Wiring
MULTIGANG INSTALLATION
When installing more than one control in the same wall box, it may be necessary to remove the side tabs before installing (see below). Using pliers, bend each tab back and forth until they break off. Repeat for each tab to be removed. Removal of tabs WILL REDUCE MAXIMUM LOAD CAPACITY.
LED/CFL Derating Chart
| Load Capacity when Tabs are removed from:
| 0 Sides| 1 Side| 2 Sides
Dimmable
LED/CFL| 150W| 150W| 150W
When using the 59302 Dimmer to control LED/CFL lights in conjunction with another 59302 Dimmer to control Incandescent /Halogen lights follow this Derating Chart for Maximum Capacitiy on EACH device.
If the combined
Wattage of ALL| Then the Maximum COMBINED Wattaged for the
Incandescent/Halogen bulbs on EACH attached dimmer:
---|---
If NO Tabs are removed then Max Wattage is:| If 1 side of Tabs are removed
then Max Wattage is:| If 2 sides of Tabs are removed then Max Wattage is:
LED/CFL bulbs on 1 dimmer is:
OW| 700W| 600W| 500W
1-25W| 500W| 400W| 300W
26-50W| 400W| 300W| 200W
51-75W| 300W| 200W| 100W
76-100W| 200W| 100W| 50W
101-125W| 100W| 50W| OW
126-150W| OW| OW| OW
If you are using ONLY LED/CFL bulbs on ALL 59302 Dimmers, DO NOT USE this Derating Chart. Follow the LED/ CFL Derating Chart.
DIMMER ADJUSTMENT
- Power the lights on by using the Rocker switch and move the dimmer’s slider down to the bottom.
- Fine Tuning: To achieve the lowest light level, turn the Tuning dial Upwards/ Downwards until desired level is reached. (Note: DO NOT overturn. The Dial will stop turning at lowest/ highest outputs).
- To verify the setting, turn the dimmer off then back on. Repeat step 2 if all bulbs do not turn on.
- Turn adjustment dial Up until all lights come on. Some dimmable CFLs and LEDs require at least two light bulbs to be installed or 10 total wattage on one lamp for proper operation.
WARRANTY INFORMATION
This device is warranted to be free of material and workmanship defects for 2 years from the date of purchase. Original receipt or proof of purchase from an authorized retailer must be presented upon warranty claim. ALL claims must be verified and approved by Enerlites, Inc. Warranties from other Enerlites products may vary. This warranty is nontransferable and does not cover normal wear and tear or any malfunction, failure, or defect resulting from misuse, abuse, neglect, alteration, modification, or improper installation. To the fullest extent permitted by the applicable state law, Enerlites shall not be liable to the purchaser or end user customer of Enerlites products for direct, indirect, incidental, or consequential damages even if Enerlites has been advised of the possibility of such damages. Enerlites’ total liability under this or any other warranty, express or implied, is limited to repair, replacement or refund. Repair, replacement or refund are the sole and exclusive remedies for breach of warranty or any other legal theory.
© 2016 Enerlites Inc. CA, U.S.A.
WWW.ENERLITES.COM
0206160008-01
REV 20230802
Documents / Resources
|
Enerlites 59302 120V Dimmer for Dimmable
LED
[pdf] Instruction Manual
59302 120V Dimmer for Dimmable LED, 59302, 120V Dimmer for Dimmable LED,
Dimmer for Dimmable LED, Dimmable LED, LED
---|---
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>