EMITEVER DNA042BU1-600-P 25W Triac Dimmable Driver Power Supply User Guide

User Guide
Triac Dimmer Switch
Works with Dimmable LED Light
CFL/Inc./Hal. Light

DNA042BU1-600-P 25W Triac Dimmable Driver Power Supply

LED/CFL:3W-200W
Dimming Method| Phase-cut
Working Environment| Temperature: 0 c. – 40 (
Humidity:10% R.H. – 90% R.H.
Model Size| 4.13in x 1.73in x 1.22in (LxWxH)

PLEASE READING BEFORE INSTALLING

1. Please confirm the compatibility with dimmable LED lights, CFLs, incandescent or halogen lights only.
2. This product should be used with an upstream air-switch.
3. Turn off power at the circuit breaker or fuse and test that power is off before installing the dimmer.
4. After installing the dimmer, it is recommended to set the minimum brightness level to ensure that bulbs turn on immediately.
5. If you are unsure about any part of these instructions, consult a professional electrician.
6. To reduce the risk of overheating and possible damage to other equipment, do not install the dimmer to control a receptacle, a motor-operated appliance, or a transformer-supplied appliance.
7. Risk of fire and electrical shock, the dimmer should be installed in accordance with appropriate electrical codes and regulations.
8. When multiple bulbs are used with one dimmer, do not mix bulb types. All bulbs shall be either LED, CFL, or incandescent. Using the same model of each bulb will enhance dimmer performance.

FUNCTIONAL PARTS INSTRUCTIONS

1. Status Indicator
   ● Indicator lights red: OFF status.
   ● Indicator lights white: ON status.
   Short press: Within 0.5s
   Long press: Over 0.5s
   Continuous short press: Each interval of short press should within 0.3s.

2. Minimum Brightness Button
   ● Short pressing this button sets the screen brightness to the minimum level. There are six minimum brightness levels.

3. Power Button
   ● Turn On: Short press once when the screen is off. Turn Off: Short press once when the screen is on. Set Brightness Minimum: Continuously short press the power button six times after setting the screen brightness to the ideal minimum level when the screen is on. Set Brightness Maximum: Continuously short press the power button eight times after setting the screen brightness to the ideal maximum level when the screen is on.
   ● To reset the minimum and maximum brightness settingse: Continuously press the power button for nine seconds when it is ON.
   ● Restore Factory Settings Button: To restore the factory default settings, continuous short press this button ten times. The status indicator will flash three times to indicate the successful restoration of the factory default settings.
   ● Brightness increase:Short press the dimming button (UP) once can increase a level of brightness when in ON status.

4. Dimming Button (UP)
   ● Brightness increase continuous:Long press the dimming button (UP) can continuous to increase the brightness until release or reach the maximum brightness.
   ● Quickly to full brightness:Continuous short press two times when in ON/OFF status to turn quickly to the maximum brightness.

5. Dimming Button (Down)
   ● Brightness decrease:Short press the dimming button (Down) once can decrease a level of brightness when in ON status.
   ● Brightness decrease continuous:Long press the dimming button(Down) can continuous to decrease the brightness until release or reach the minimum brightness.
   ● Quickly to minimum brightness:Continuous short press two times when in ON/OFF status to turn quickly to the minimum brightness.

6. Power Cut-off Button
   ● To connect or cut off power, insert or remove the power cut-off button accordingly.

7. Luminance Indicator ● Luminance Indicator Table

PARTS INFORMATION

INSTALLATION

Step1 Warning
To prevent fire and electrical shock, always turn off power at the circuit breaker or fuse before wiring.
Step2 Remove existing device
To remove an existing device, first remove the screws installed on the existing panel and switch. Carefully pull out the switch from the wall box, identify and remove the power cord attached to the switch, then remove the switch. Do not remove the power cord detached from the switch. (This step is not required for new configuration installation.)
Step3 Idepyt tiucric 1 noitacoL yfitnedI
Note: If the wiring in the wall box is different from the following layouts, please consult an electrician.
Single-Pole(Use wiring diagram step 4a below)

3-Way(Use wiring diagram step 4b-1/2 below)

IMPORTANT: For 3-Way applications, note that one of the screw terminals from the old switch being removed will usually be a different color (Black) or labeled Common. Tag that wire with electrical tape and identify as the common (Line or Load) in both the dimmer wall box and 3-way wall box. Bae) Wiring diagram Step 4a: Single-Pole

Location 1 wiring:

• Connect the green wire on the dimmer with the green or bare copper ground wire on the wall box and tighten it by screwing the P3 wiring nut.
• Connect the black wire on the dimmer with the live wire of the circuit breaker or load wire and tighten it by screwing the P3 wiring nut.
• Connect the red wire on the dimmer with the live wire of the circuit breaker or load wire and tighten it by screwing the P3 wiring nut.
• Protect the remaining brown wire on the dimmer by screwing the P3 wiring nut.

Step 4b-1: 3-Way (3-way Switch)
NOTE: Only one dimmer can be used per circuit

Location 1 wiring:

• Connect the green wire on the dimmer to the green or bare copper ground wire on the wall box and screw in the P3 wiring nut.
• Connect the black wire on the dimmer to the live wire of the circuit breaker or load wire and screw in the P3 wiring nut.
• Connect the brown wire on the dimmer to the Traveler 2 and screw in the P3 wiring nut.
• Connect the red wire on the dimmer with Traveler 1 and tighten it by screwing the P3 wiring nut.

Location 2 wiring:

• Connect Traveler 2 to Screw 1 or Screw 2 of the 3-way Switch.
• Connect the 3-way Switch Common Terminal to the jumper wire. Then, connect Traveler 1 to the jumper wire, as well as the live wire of the circuit breaker or load wire, and tighten it by screwing the P3 wiring nut.

Step 4b-2: 3-Way(Toggle Switch)
NOTE: Only one dimmer can be used per circuit

Location 1 wiring:

• Connect the green wire on the dimmer to the green or barecopper ground wire on the wall box and tighten it by screwing the P3 wiring nut.
• Connect the black wire on the dimmer to the live wire of the circuit breaker or load wire and tighten it by screwing the P3 wiring nut.
• Connect the brown wire on the dimmer to Traveler 2 and tighten it by screwing the P3 wiring nut.
• Connect the red wire on the dimmer to Traveler 1 and tighten it by screwing the P3 wiring nut.

Location 2 wiring:

• Connect Traveler 2 to Screw 1 of the Toggle Switch.
• Connect Screw 2 of the Toggle switch to the Jumper wire, then connect Traveler 1 to the Jumper wire, as well as the live wire of the circuit breaker or load wire, and tighten it by screwing the P3 wiring nut.Install the dimmer.

Step5 Install dimmer

• Position all wires carefully inside the wall box, leaving enough space to insert the dimmer and tighten them with the matching screws.

Step6 Install the split panel

Compatible with integrated panel but does not include

• Install the mounting frame on the dimmer and secure it with the matched screws.
• Put the panel and mounting frame together, press gently to make sure it is be installed firmly.

USING INSTRUCTION

Short press: Within 0.5 seconds
Long press: More than 0.5 seconds
Continuous quick press: Less than 0.3 second between two quick presses.
Table 1 Single-Pole

Table 2 3-way

Function| Dimmer Operation Way| Dimmer Operation| 3-way Switch or
Toggle Switch Operation
---|---|---|---
ON/OFF| Short press the power button once| V| V
Dimmin g| Short or long press the dimming button (Up/Down)| V| X
Quickly turn to the maximum brightest| Continuous short press the dimming Button (UP) twice| V| X
Quickly turn to the minimum brightest| Continuous short press the dimming Button (Down) twice| V| X
Setting the maximum brightness| Continuous short press Power Button 8 times| V| X
Setting the minimum brightness| Short press the minimum Brightness Button| V| X
Continuous short press Power Button 6 times| V| X
Clear the minimum and maximum brightness| Continuous short press Power Button 9 times| V| X
Restore factory Settings| Continuous short press Power Button 10 times| V| X

TOOLS NEEDED TO INSTALL THE DIMMER

TROUBLESHOOTING

One dimmer been connected to multiple types bulbs, incur interference and cause flicker.| Change bulbs to same type.
Abnormal| Put the power cut-off button out and cut off the power,then put the power cut-off button in and connect the power on again.
LED and CFL flickers at low end of dimming range.| Load compatibility is not good.| Turn up lamp minimum brightness properly.
Lamps can’t be turn on| Circuit breaker has tripped.| Turn power on
Fuse burn out| Change fuse
Lamp burned out| Change lamp
Lamp neutral connection is not wired| Reconnect the lamp neutral
Lights out of control| Abnormal| Put the power cut-off button out and cut off the power,then put the power cut-off button in and connect the power on again.
Dimmer can not work in 3-way connection| Wrong or bad connection| Re-check the connection
Abnormal of 3-way switch| Change a new 3-way switch

CUSTOMER SERVICE

| Warranty:5-Years Limited Warranty
---|---
| Support ：Lifetime Technical Support
| service@emitever.com

If you have any questions, please feel free to contact us!

Documents / Resources

| EMITEVER DNA042BU1-600-P 25W Triac Dimmable Driver Power Supply [pdf] User Guide
EMITEVER DNA042BU1-600-P 25W Triac Dimmable Driver Power Supply, EMITEVER DNA042BU1-600-P, 25W Triac Dimmable Driver Power Supply, Triac Dimmable Driver Power Supply, Dimmable Driver Power Supply, Driver Power Supply, Power Supply, Supply
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>