TEVII G402TX SmartShare 4K Pro User Guide

TEVII G402TX SmartShare 4K Pro

Introduction

SmartShare 4K Pro is an intuitive and high-efficiency 4K wireless presentation and collaboration system that enables any meeting participant to simply share the content from their laptop, mobile phone, or tablet on the projector or large screen wirelessly, no APP required, no setup, no messy cables, just click and share. SmartShare 4K Pro supports up to 16 presenters to share their content instantly without wasting valuable meeting time. A standard SmartShare 4K Pro is a combination of one transmitter and one receiver, the receiver is connected to a projector or display, and the transmitters are connected to a PC or any device with an HDMI jack, after connected, users click the button on the transmitter and the screen will be streaming to the display, it’s easy for other users to switch by click. You can buy an additional transmitter or receiver if needed. Never have to worry about the software configuration, no compatibility, WIFI and network set up, no need IT support, with our powerful and simple solution, everyone can immediately know how to use it for collaborative presentations, which significantly improves corporate efficiency and productivity.

Product Features

Plug and play

| Simply connect the transmitter with the PC HDMI ports, then click the button to start the streaming.

App Free

| SmartShare 4K Pro doesn’t need any software or app installation, no setup, no IT team.
All in one| Support iOS/Android/Windows system, support Blu-ray DVD player,

media player and any devices with HDMI jack.

Wireless Camera

| ****

Share the images and audio from smart-phone camera or to the large display simultaneous.

Multi-user mode| Up to 16 user’s presentation at one time

Auto Channel Selection

| The SmartShare 4K Pro will select the best Wi-Fi channel automatically after power on to ensure streaming smoothly.
Fast Speed with 5G AC MIMO Technology| The SmartShare 4K Pro comes with the fast 802.11ac MIMO technology

which increase Wi-Fi speeds by allowing a pair of wireless devices to simultaneously send or receive multiple data streams.

4K60 High Resolution Quality| SmartShare 4K Pro support 4K high resolution, which means much more clear pictures, rich in details and texture compared with 1080p.

High Security Protection

| No worries about the data security, the SmartShare 4K Pro support AES 128-bit security encryption and WPA2/WPA-PSK/WPA2-PSK authentication protocol to protect data. HDCP supported to protect the

content.

Package Included

Devices Requirement
Please ensure the devices meet the following requirements:

• iOS 9.0 or above
• Android 5.0 or above

Product Specification

Feature|
---|---
Video input| Up to 4K30
Video output| Up to 4K60
Audio| Stereo, quality 16bits 48KHz
Wireless Channel| IEEE 802.11ac, 5GHz, 2T2R
Latency| About 100ms latency
Streaming Protocol| Airplay, Miracast, DLNA
HDMI Version| HDMI2.0
Authentication Protocol| WPA2 (WPAS-PSK / WPA2-Enterprise)
Security| AES 128 bit
Platform supported| Windows, iOS, Android system, Any devices with HDMI jack
Distance| About 50 meters in the clean line of sight
Transmitter|
interface| HDMI in jack x 1, Type c x 1, button x 1
LED| Red and blue
Switch button| x 1
Power supply| DC5V/0.7A
Battery capacity| 780mA Polymer battery
Power Consumption| About 3.5 W
Dimension| 83x32x13mm
Weight|
---|---
Receiver|
Interface| HDMI out jack x 1, Type c x 1, button x 1
LED| Blue
Power supply| DC5V/1 A
Power Consumption| About 3W
Dimension| 83x32x13mm
Weight|
Temperature Range|
Operating:| 0°C to +40°C (+32°F to +104°F)
Storage:| -10°C to +60°C (+14°F to +140°F)
Humidty|
Operating:| 10% to 80% relative humidity
Storage:| 5% to 90% relative humidity

Overview

TX

1. HDMI in: connect with the HDMI port of the source devices.
2. Button: click to cast
3. LED: to display different statues.

1. Reset: press the button up to 3s for a factory reset
2. Type C: for power supply.

TX Playback time

1. Some video sources’ HDMI has 5V output, which ensures TX up to 4 hours of playback.
2. If the video source’s HDMI has no power output, the built-in battery of the TX can support 50 minutes of playback. If the battery is running out, please place the TX into the cradle for charging.

LED indicator of the SmartShare 4K Pro TX

RX

1. HDMI out: connect with monitor or projector.
2. Button： Long press 9s for factory reset
3. LED: to display different statues.
4. Type C: for power supply.

LED indicator of the SmartShare 4K Pro

RX

| Description
---|---
Flashing blue| Waiting for connection
Static blue| Connected and start to presenting

Receiver Installation

1. Connect the RX with the HDMI port of the display.
2. Connect the type c port of RX to the TV USB port through the USB cable for power supply.

Remark: Remark: the power supply of RX is about 5V/0.5A. Please connect the RX with a power adapter if your TV can’t supply enough power.

Connect to internet

• Connect the RX SSID with your smart devices, the SSID and password are shown on the left upper corner of the screen.

• Open the browser with your phone, and input the IP address that shows on the right upper corner of the screen to enter to the RX management platform. Remark: when connected to the router, the IP address will be updated accordingly.

• Select the network and connect to the management platform, the RX will link to the network and show the network SSID on the middle of the screen. (to get better performance, we recommend connecting with 5G router)

• Select the network and connect to the management platform, the RX will link to the network and show the network SSID in the middle of the screen. (to get better performance, we recommend connecting with 5G router)

AP password management:
Users can change AP passwords on the management page. Remark: if the password is changed, the TX and RX have to pair again.

Language
Users can change the language on the management page:

Screen Position
If the RX HDMI OUT size is not compatible with the display, the user can use Screen Position to adjust the zoom-in and zoom-out the screen.

Airplay mode: you can select to use streaming mode or Mira mode.

Pairing a transmitter and receiver
A standard SmartShare 4K Pro set includes one receiver and one transmitter, which are paired before shipment. Normally you don’t need to pair them again. However, if you buy an additional transmitter or upgrade to new software, you need to follow the instructions below to pair the new transmitter with the receiver.

Pairing instruction:

1. Power on the receiver and connect with the display and wait for RX to enter the home page.
2. Power on the TX and wait around 5-10seconds, the button light of the TX will turn to flash red, Then hold the reset button up to 3 seconds till the button flash fast for factory reset, then the TX will restart and the LED light will turn from red to flashing blue after 30s automatically.
3. Click the TX button to stream when the TX LED is turning to flash blue.

Stream from TX: SmartShare 4K Pro TX Installation

1. Connect the SmartShare 4K Pro TX’s HDMI to the PC HDMI port.
2. The LED indicator of the SmartShare 4K Pro TX will turn red when it’s booting up.
3. The LED indicator will become blue and flash when SmartShare 4K Pro is ready to stream.
4. Click the button to start casting, the LED indicator will become constant blue.

Streaming from smart devices

1. iOS devices

   • Search RX SSID and connect. (SSID: RXxxxxx, Password: 12345678), the SSID is shown on the left upper corner of the screen.
     Remark: if the RX is already connected with your network, just make sure your device is in the same network with RX.

   • Stream the content from your iOS devices via Airplay.

Android devices

• make sure your Android device’s Wi-Fi is available, and select the miracast function of your phone and start to stream.

Remark: there are different names on different brand phones or tablets: WIFI Display, WLAN Display, Wireless Display, Allshare Display, Allshare Cast, Wireless Display TX:

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used following the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF warning statement:

• The device has been evaluated to meet general RF exposure requirements. The device can be used in portable exposure conditions without restriction.

Specific Absorption Rate (SAR) information

• This radio is designed for and classified as “General population/uncontrolled Use”, the guidelines are based on standards that were developed by independent scientific organizations through periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health. The exposure standard for wireless radio employs a unit of measurement known as the Specific Absorption Rate or SAR, the SAR limit set to 1.6W/kg.
• Body-worn operation; this device was tested for typical body-worn operations with the Down of the Transmitter kept 0mm for body-worn. To maintain compliance with RF exposure requirements, use accessories that maintain a 0mm for body-worn. The use of belt clips, holsters and similar accessories should not contain metallic components in their assembly. The use of accessories that do not satisfy these requirements may not comply with RF exposure requirements and should be avoided. The highest reported SAR value for worn on the body is 0.444W/kg and Simultaneous SAR is 0.862 W/kg

FCC STATEMENT

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, under Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance 20cm between the radiator & your body. The UNII Band 5150-5250MHz indoor use only.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>