CHAINWAY CM710-1 1-Port RFID Module User Manual
- June 14, 2024
- CHAINWAY
Table of Contents
CHAINWAY CM710-1 1-Port RFID Module User Manual
CM710-1 / CM510-1 / CM310-1 is a 1-port RFID module based on Impinj E710 / E510 / E310 chip. It can be integrated in mobile RFID readers, fixed RFID readers, card issuers and etc. With high integration level, it is small in size, lowin power consumption, resistant to electromagnetic interference and good at heat dispersion. The module appeals to challenging industries like warehousing, logistics, apparel, production lines and such.
Dimensions
Interface Definition (12 PIN)
PIN#12| InterfaceVIN
VIN| Description3.5-5.25VDC
---|---|---
3| GND| Ground
4| GND| Ground
5| EN| High LLT level (>1.2V) boot the module
Low LLT level (<0.4V) out the module
6| 101| Reserved GPIO 3.3V TTL level
7| 102| Reserved GPIO 3.3V TTL level
2| 103| Reserved GPIO 3.3V TTL level
| RXD| UART receive 3.3V TTL level
10| TXD| UART transmit 3.3V TTL level
11| NC|
“2| NC|
Specification
Model
1-Ports RFID Module: CM710-1 / CM510-1 / CM310-1
Development Board Module : CM-X_EDCB
Physical Characteristics
Dimensions: 57.2 mm x 36.8 mm x 7.6 mm
Weight: 26.0 g / 0.92 oz.
RFID Features
RF Chip : Impinj E710 / 510 / 310
Air Interface Protocol: EPCglobal Gen2 (ISO18000-6C) Working Frequency
865-868 / 920-925 / 902-928 MHz ( custom design for frequency band )
Output Power 1-30dBm adjustable; 1dB step interval; +/- 0.5dB precision
Output Powe r: Flatness +/- 0.2dB
Antenna Interface :50Ω RF connector MMCX Receptacle
Regions Supported: FCC 902-928 MHz; ETSI 865.6-867.6 MHz; China
920-925MHz; Others for customization (865-868, 902-928MHz)
Receive Sensitivity
CM710-1 : < -87 dBm;
CM510-1: < -81 dBm;
CM310-1 : < -74 dBm;
Tag RSSI: Supported
Antenna Detector : Supported
Ambient Temp Monitor: Supported
Working Mode: Single/DRM
Communication Interface
Connector: 12 PIN FPC Connector
Host Communication: UART 3.3V TTL Level
Baud Rate: 115200bps
Power Supply
Input Voltage : DC 3.5-5.25V
Power Consumption in RF Output Mode: 7.5W
Power Consumption in Standby (EN high TTL level) : 0.175W;
Power Consumption in Power Down (EN low TTL level): 42.5uW
User Environment
Operating Temp: – 13o F to 149o F / -25o C to 65o C
Storage Temp: -40o F to 185o F / -40o C to 85o C
Humidity: 10% – 95%
Reading Performance
Fastest Read Rate
CM710-1 : 950+ tags/s;
CM510-1: 550+ tags/s;
CM310-1: 250+ tags/s;
Reading Range: Up to 10m (with 4dBi antenna)
Notice: Product specifications are subject to change without prior
notice. / Model: CM710-1 CM510-1 /CM310-1 / Update Date: 2022-04-02Shenzhen
Chainway Information Technology Co., Ltd
Address: 9F, Building2, Phase 2, Gaoxinqi Industrial Park, Liuxian 1st Rd.,
Bao’an District, Shenzhen, Guangdong 518102, China
Tel: 0086-755-23223316
Fax: 0086-755-23223310
Email: sales@chainway.cn Web:
http://www.chainway.net
FCC Information
RF Exposure Information: To maintain compliance with FCC RF exposure requirements, use the product that maintain a 20cm separation distance between the user’s body and the host.
FCC statements:
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause un desired operation.
NOTE: The manufacturer is not responsible for any radio or TV interference caused by unauthorized modifications or changes to this equipment. Such modifications or changes could void the user’s authority too pate the equip NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help
This device is intended only for OEM integrators under the following conditions:
- The antenna must be installed such that 20 cm is maintained between the antenna and users.
- The transmitter module may not be co-located with any other transmitter or antenna. As long as the two conditions above are met, additional transmitter testing will not be required. However, the OEM integrator is still responsible for testing their end-product for any additional compliance requirements required for the installed module.
Important Note:
In the event that these conditions cannot be met (for example certain laptop
configurations or co-location with another transmitter), then the Federal
Communications Commission of the U.S. Government (FCC) and the Canadian
Government authorizations are no longer considered valid and the FCC ID cannot
be used on the final product. In these circumstances, the OEM integrator shall
be responsible for re evaluating the end-product (including the transmitter)
and obtaining a separate FCC authorization in the U.S. and Canada. OEM
Integrators – End Product Labeling Considerations:
This transmitter module is authorized only for use in device where the antenna
may be installed such that 20 cm may be maintained between the antenna and
users. The final end product must be labeled in a visible area with the
following: “Contains, FCC ID: 2ABGH RC101ML”. The grantee’s FCC ID can be used
only when all FCC compliance requirements are met.
OEM Integrators – End Product Manual Provided to the End User:
The OEM integrator shall not provide information to the end user regarding how
to install or remove this RF module in end product user manual. The end user
manual must include all required regulatory information and warnings as
outlined in this document.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>