WHALL Slow ZM1512 HALL Slow Masticating Juicer User Manual

ZM1512

User Manual

Household use only
Please read the instruction manual carefully before using

WHALL(HONGKONG)GLOBAL BUSINESS CO.,LIMITED
FLAT/RM B,5/F GAYLORD COMMERCIAL BUILDING,114-118 LOCKHART ROAD, HK
sj.aftersale@outlook.com

CHAPTER 1: SAFETY PRECAUTIONS IN USE

1. The input voltage of the appliance is 120V/60Hz. Please confirm it before using the appliance.
2. Do disconnect the power supply before dismantling, assembling or adjusting any part of the appliance.
3. The appliance has Y connection. If its power cord is damaged, please contact our customer service department for replacement (Email: sj.aftersale@outlook.com) to avoid dangers. Do not dismantle and repair it by yourself.
4. Before use, please check if the power cord, the plug, the juice strainer, the spiral pusher and any other part is damaged. If any of the said part is damaged, stop using the applianceand contact our customer service department  promptly. Do not dismantle and repair it by yourself, otherwise dangers may happen.
5. If it is necessary to repair the appliance during use, please contact our customer service department. Do not dismantle it by yourself, otherwise dangers may happen.
6. It is necessary before connecting the power supply to ensure that the juicing body, the spiral pusher, the juicing body cap and all other dis-mountable parts are properly installed.
7. Never put hands or sharp objects into the feed port or contact the spiral pusher when the appliance is running, otherwise injuries may be caused or the appliance may be damaged; never replace the spiral pusher with any other  objects or have eyes get close to the feed port, otherwise accidents may happen.
8. Cut food ingredients into small blocks with sizes fitting the feed port of the juicing body. Do not begin to process any vegetables or fruits with cores, hard seeds or thick skin or shells until they are removed.
9. When feeding a food ingredient, do not make the pushing force too large but have it just enough to cut the food ingredient.
10. Dyeing of the juice strainer, the juicing body cap, the spiral pusher and other accessories after juicing some vegetables or fruits is normal and will neither affect food eating nor do harm to health.
11. Do not dismantle the dis-mountable parts of the appliance immediately after use but afterboth the motor and the spiral pusher have stopped and the power supply is disconnected.
12. Do not sterilize any accessories of the appliance with hot water that is higher than 80℃ or a microwave oven, otherwise they may be heated, deformed and damaged. The materials of all parts in contact with food ingredients should comply with food hygiene certificationand be clean, hygienic and reliable.
13. Do not put the main body into water or another liquid or flush it with water or another liquid, otherwise it may be damaged.
14. Do not clean the appliance with steel wool, abrasive cleaning agents or corrosive liquids(such as gasoline or acetone).
15. The appliance is applicable to use by individuals or families only.
16. The appliance is not to be used by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have beengiven supervision or instruction. children being  supervised not to play with the appliance.
17. Accessories, other than those supplied with the appliance, include instructions for their safe use.
18. Use a wet cloth to clean surfaces in contact with food before unplug the plug.
19. Switch off the appliance and disconnect from supply before changing accessories or approaching parts that move in use.
20. If the supply cord is damaged, it must be replaced by the manufacturer, its service agentor similarly qualified persons in order to avoid a hazard.
21. Warning: potential danger may be against misuse
22. Always disconnect the appliance from the supply if it is left unattended and before assembling, disassembling or cleaning.

CHAPTER 2: PARTS AND FUNCTIONS

full contact with the spiral pusher and higher juice extraction efficiency.
2| Tray| It is mainly used for storing the extracted food ingredients.
3| Juicing
body| It is a main part for juicing. Food ingredients are first fed via the feed port at the top of the juicing body and then discharged in forms of juice and pulp via the juice outlet and the pulp outlet respectively

CHAPTER 3: DIRECTIONS FOR USE

• Before using the appliance for the first time, clean its parts in contact with food ingredients thoroughly (please refer to “Chapter 4: Maintenance”).

Button operation instructions:

• On button: Function Start
• “0” button: Close and stop
• “R” button: It is used when pulp discharge is blocked or the motor is locked

Use of the appliance
Please install and use the appliance following the steps below.

| 1| Connect the juicing body and the main body:
1. Have the triangular aligning sign “▼” on the     juicing body aligned with the aligning “unlocking triangular sign” on the main body and  then put the juicing body into the main body (the three clips on the juicing body will realize alignment).
2. Then turn the juicing body anticlockwise. When there is a click, it suggests that the connection is finished.
---|---|---
| 2| Have the hexagonal shaft of the spiral pusher aligned with the hole on the main body and push it horizontally until it reaches the bottom (when alignment fails, just turn the spiral pusher slightly).
| 3| Fit the larger-hole end of the juicer strainer into the tail of the spiral  pusher and push it while the three clips of the juicer strainer align with  the three clamping slots in the juicing body. (The juicestrainer is used with the juicing button in the rear only. This function is used for juicing.)
| 4| Align the triangle alignment mark on the juice extractor with the unlock triangle mark on the juice extractor, and then put the end cup into the juice extractor.
| 5| Put the juice cup in the corresponding groove on the main body and have its opening aligned with the bottom of the juice outlet of the juicing body.
| 6| Put the pulp cup below the pulp outlet of the juicing body and have it close to the juice cup.
| 7| Install the tray on the upper end of the feed port of the juicing body. The  tray can make feeding of food ingredients more convenient, particularly when small-particle food ingredients like grapes and strawberries are processed.
| 8| Connect the power supply for use of the appliance (make sure the switch is on the OFF position before the power supply is connected).
| 9| Wash vegetables and fruits, cut them into blocks fitting the size of the feed port and put them on thetray.
| 10| Put food ingredients into the feed port on the juicing body cap and then push the food ingredients with help of the pushing rod.

CHAPTER 4: MAINTENANCE

1. Before cleaning the appliance, do switch off the switch and disconnect the power supply.
2. After use, clean the appliance promptly.
3. Do not wash the main body with water but wipe the stains on it with a piece of wrung rag or cotton cloth.
4. Before storing the appliance, make sure it is clean and dry.
5. Clean the appliance after dismantling it following the steps below.

| 1| Take down the pushing rod and the tray.
---|---|---
| 2| Press the button on the side of the juicing body and turn the juicing body  clockwise at the same time to take out the juicing body. The juicing body cannot be dismantled if the button is not pressed.
| 3| After taking down the juicing body, take down the juicing button, the juicing body cap, the juice strainer (or the squeezer) and the spiral  pusher in order. The dismountable parts may be flushed with clean water.

CHAPTER 5: MAINTENANCE

Notes:
What given about are the analysis and elimination methods of ordinary faults. For other faults, please contact our customer service department or have the appliance directly repaired by a service center designated by us. Do not dismantle  and repair it by yourself.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>