HOTO QWSDT001 LED Rechargeable flashlight Instruction Manual
- June 14, 2024
- HOTO
Table of Contents
QWSDT001 LED Rechargeable flashlight
Stay tuned to our social media (@hoto_official)
https://qrcode.hototools.com/
Product Overview
Read this manual carefully before use, and retain it for future reference.
Thank you for using HOTO flashlight Lite
- Diffuser
- Focus Ring
- Main Switch
- Strobe/SOS switch
- Hook
- Indicator Light
- Type-C charging port
How to Use
Focusing
- Push the focus ring up and down to achieve the effect of focusing and flooding.
Main Switch
- Daily use: short press to turn it on (low light mode by default). Short press again to adjust to medium light mode; again to high light mode; and again to shut it down. Repeat the operation.
- During charging: Short press to turn it on to low light mode; short press again to shut it down. Repeat the operation.
Strobe/SOS switch
- Short press to turn on the strobe mode; short press again to switch to SOS mode; short press again to shut down; Repeat the operation.
- The strobe mode: in this mode, high-frequency flashing and strong light stimulation can be used to disturb the line of sight of any potential perpetrators for defense.
- SOS mode: in this mode, the flashlight automatically flashes with three dits, three dats, and three dits to signal for help to the outside world.
Indicator status
Operating status
- Battery is above 60%: green light is on.
- Battery is between 30%-60%: orange light is on.
- Battery is between 10%-30%: red light is on.
- Battery is less than 10%: red light flashes. (Attention: After the red light flashes for a while, the main lamp of the flashlight will flash and be forced to turned off in about 2 minutes. In that case, please charge the device.)
Charging status
- Charging: red light breathes;
- Fully charged: green light is on.
This flashlight is equipped with a Type-C charging port, and a USB charging cable is included.
**** General Power Tool Safety Warnings
Safety matters
Correct use
Please use the tool properly as guided in this document.
Maintenance service
This product cannot be disassembled. Only the maintenance personnel authorized
by our company can repair the product. Please do not repair it yourself to
avoid possible harms.
Charging instructions
- Only use the charger that is in line with the charging parameters of the tool for charging;
- If the status indicator does not display normally when it is not used for a long time, please continue to charge for 30 minutes and check it again.
Instructions for use
- This product can emit strong light. Please avoid having it emit direct light to human, animal eyes and optical equipment lens;
- In order to reduce the risk of harm, children should use the flashlight when with their parents;
- To reduce the risk of electric shock, do not put the tool in water or other liquids;
- Do not place or store the tool where it may fall into the bathtub or sink;
- After the strobe mode is turned on for a long time, the focus ring may generate high temperature. To reduce the risk of burns, please do not touch it.
Warning
- Please use a charger that is in line with the charging parameters of the tool for charging. Other types of chargers and accessories may violate the product warranty and may cause danger.
- 15 minutes after the highlight mode is turned on, the temperature will increase by about 20°C. For users who are sensitive to temperature, please implement heat insulation measures. （After 25 minutes, the temperature will slowly decrease. ）
- After the product detects that the battery reaches 45°C, it will trigger the charging protection function and stop charging. The recommended charging environment temperature is 0 ℃ -30 ℃.
General malfunction and troubleshooting methods
| Issue | Possible Causes | Solution |
|---|---|---|
| Press the main switch or strobe/SOS switch, the red light flashes. | Low li-ion | |
| battery power | Charging | |
| Press the main switch or strobe/SOS switch, the flashlight does not light up. | ||
| No li-ion battery power | Charging | |
| The indicator light on the main switch does not light up during charging. | The | |
| USB cable is not plugged in, or the specified charging cable is not used. | Use |
the specified charging cable; use 5V power adapter; check whether the indicator light is on.
Specifications
Model: QWSDT001
Item Dimensions: 164.5x 30 x 30 mm
Net Weight: Approx.160 g
Input: 5V 1A
Battery Type: Lithium-ion battery
Battery Capacity: 2600 mAh
Rated Voltage: 3.65V
Charging Time: Approx.210 min
Main switch three-mode parameters
| High light mode| 350LM| Low light mode
---|---|---|---
Brightness| 1000LM| 3.5H| 50LM
Run time| 2H| Medium light mode| 24H
Manufactured by: Shanghai HOTO Technology Co., Ltd.
Address: Building 45, No.50 Moganshan Road, Putuo District Shanghai,China
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>