HOTO QWXCJ002 20V Pressure Washer Pro Gun User Manual

QWXCJ002 20V Pressure Washer Pro Gun

User Manual for HOTO 20V Pressure Washer Pro

WARNING! You must read this manual thoroughly before using HOTO 20V Pressure Washer Pro!

Stay tuned to our social media (@hoto_official)

Product Overview
Thank you for using HOTO 20V Pressure Washer Pro. Read this manual carefully before use, and retain it for future reference.

• Multi-Function Nozzle
• Spray Lance
• Soap Holder
• Handle
• Trigger
• Battery Pack
• Battery Level Display Button
• Hose Inlet
• Hose Clip
• Water Inlet Filter
• Water Inlet

Operating Instructions

Component assembly

Install the battery pack: Align the mark on the handle with the mark on the battery pack. Rotate the battery pack 90 degrees in the arrow direction so that the mark is aligned with
the mark. There will be a sound of locking for successful assembly.

Connection of the hose inlet: Plug hose inlet into water inlet as shown in the diagram.

Assembly of the spray lance: Align the reducer of spray lance with the slot inside handle. Rotate the gun 90 degrees in the arrow direction so that spray lance restores.

Assembly of the soap holder: Align soap holder with the slot in spray lance in the arrow direction. Rotate it about 45 degrees in the arrow direction to lock soap holder.

Disassembly of components

Disassembly of the battery pack: Rotate battery pack 90 degrees in the arrow direction so that the mark is aligned with the mark; Remove battery pack downward.

Disassembly of the hose inlet: Hold hose inlet at its largest diameter position in the upper part, and then pull it out downward.

How to use

Connect the water pipe: Put hose inlet into a bucket and fix it to the edge of the bucket with hose clip. Connect water inlet filter.

Add detergent: Remove soap holder, add detergent or car washing liquid (powder), and then close the soap holder.

Disassembly of the spray lance: Press and push backward spray lance in the arrow direction, and then rotate spray lance 90 degrees in the arrow direction and draw it out.

Disassembly of the soap holder: Rotate soap holder 45 degrees in the arrow direction Remove soap holder in the arrow direction.

Change the water type: Rotate the shell of multifunctional nozzle to align the arrow with the corresponding mark on the shell to change the water type. Five water types are available circularly.

• Jet mode: It is used to rinse stubborn stains, such as dry stains on the car’s surface.
• Tilted mode: It is used to clean the top of the car and other higher planes.
• 20-degree/40-degree water mode: The two modes are all used for routine cleaning purposes, such as washing cars, bicycles, motorcycles, windows, or fences, and only have differences in water spray angles.
• Foam/Shower mode: The washer working in this mode can spray foam when there is soap in the soap holder, or can be used as a shower when there is no soap.

Self-lock the start button: Switch trigger down to the mark to self-lock the button (so that the motor will not work if trigger is pressed). Restore trigger to the mark to lift self-lock.

Checking the Battery Level During Use

During Charging:

• Battery level 100%: Press the battery level display button, and four indicators will remain on for 20 seconds and then go off.
• Battery level 75%-100%: Indicators 1, 2, and 3 remain on, and indicator 4 blinks.
• Battery level 50%-75%: Indicators 1 and 2 remain on, and indicator 3 blinks.
• Battery level 25%-50%: Indicator 1 remains on, and indicator 2 blinks.
• Battery level 0%-25%: Indicator 1 blinks.

Product Overview

Thank you for using HOTO 20V Pressure Washer Pro.
Read this manual carefully before use, and retain it for future reference.

1. Multi-Function Nozzle
2. Spray Lance
3. Soap Holder
4. Handle
5. Trigger
6. Battery Pack
7. Battery Level Display Button
8. Hose Inlet
9. Hose Clip
10. Water Inlet Filter
11. Water Inlet

Operating Instructions
Component assembly

Install the battery pack：

• Align the “●” mark on the handle with the ” ” mark on battery pack.
• Rotate battery pack 90 degrees in the arrow direction so that the “●” mark is aligned with the ” ” mark. There will be a sound of locking for successful assembly.

Assembly of the spray lance:
Align the reducer of spray lance with the slot inside handle.
Rotate the gun 90 degrees in the arrow direction so that spray lance restores.

Connection of the hose inlet:
Plug hose inlet into water inlet as shown.

Assembly of the soap holder:

• Align soap holder with the slot in spray lance in the arrow direction.
• Rotate it about 45 degrees in the arrow direction to lock soap holder.

Disassembly of components
Disassembly of the battery pack:

• Rotate battery pack 90 degrees in the arrow direction so that the “●” mark is aligned with the ” ” mark;
• Remove battery pack downward.

Disassembly of the spray lance:
Press and push backward spray lance in the arrow direction, and then rotate spray lance 90 degrees in the arrow direction and draw it out. Disassembly of the hose inlet:
Hold hose inlet at its largest diameter position in the upper part, and then pull it out downward.

Disassembly of the soap holder:
Rotate soap holder 45 degrees in the arrow direction。
Remove soap holder in the arrow direction.

How to use

• Connect the water pipe: Put hose inlet into a bucket and fix it to the edge of the bucket with hose clip. Connect water inlet filter.
• Change the water type: Rotate the shell of multifunctional nozzle to align the arrow “●” with the corresponding mark on the shell to change the water type. Five water types are available circularly.
• “ ” Jet mode: It is used to rinse stubborn stains, such as dry stains on the car’s surface.
• “ ” Tilted mode: It is used to clean the top of the car and other higher planes.
• ” ” 20-degree/40-degree water mode: The two modes are all used for routine cleaning purposes, such as washing cars, bicycles, motorcycles, windows, or fences, and only have differences in water spray angles.
• “ ” Foam/Shower mode: The washer working in this mode can spray foam when there is soap in the soap holder, or can be used as a shower when there is no soap.
• Add detergent: Remove soap holder, add detergent or car washing liquid (powder), and then close the soap holder.
• Self-lock the start button: Switch trigger down to the “ ” mark to self-lock the button (so that the motor will not work if trigger is pressed). Restore trigger to the “ ” mark to lift self-lock.
• Battery pack: The USB-C interface of the battery pack supports the two-way fast charge with an output of 40 W MAX USB-C. The USB-C port supports the fast charging input of 40W MAX. The
• USB-C port supports the fast charge output of 40 W MAX, thus providing the fast charging experience in a more efficient manner.
• Charge the battery pack: Remove the waterproof cover over the charge port of the battery pack, and connect the Type-C connector of the charger cable to the charge port of the battery pack and the other end of the cable to power supply.
• Discharge the battery pack: This product can be discharged through USB-C. You may purchase a two-way Type-C charger cable separately(or Apple charging cable with one end of Type C). Plug one end of the Type-C interface of the charger cable into the USB-C interface of the battery pack and the other end of the Type-C interface of the charger cable into the equipment that supports the USB-C interface.

Checking the Battery Level During Use

• Battery level 75%‒100%: Press the battery level display button, the four indicators will remain on for 10 seconds and then go off.
• Battery level 50%‒75%: Press the battery level display button, and three of the four indicators will remain on for 10 seconds and then go off.
• Battery level 25%‒50%: Press the battery level display button, and two of the four indica-tors will remain on for 10 seconds and then go off.
  Battery level 0%‒25%: Press the battery level display button, and one of the four indicators will remain on for 10 seconds and then go off.

During Charging

• Battery level 100%: Press the battery level display button, and four indicators will remain on for 20 seconds and then go off.
• Battery level 100%: The total four indicators remain on for 20 seconds and then go off. Battery level 75%‒100%: Indicators 1, 2, and 3 remain on, and indicator 4 blinks.
• Battery level 50%‒75%: Indicators 1, and 2 remain on, and indicator 3 blinks.
• Battery level 25%‒50%: Indicator 1 remains on, and indicator 2 blinks.
• Battery level 0%‒25%: Indicator 1 blinks.

Safety Precautions

Safety Warnings for Washer

• Do not spray water on devices with electrical components.
• Please stop using the washer immediately if there is visible damage or leakage caused by bumping or falling.
• Do not spray water on yourself or others in an attempt to wash clothes, shoes, or socks. Disconnect the washer from power before the maintenance.
• High-pressure hoses and connectors are critical to the washer. Use only the accessories like hoses and connectors provided or approved by the manufacturer to ensure the safety of the washer.
• Do not use the washer if the power cord or key components like the hose and soap holder are damaged, or the safety function malfunctions.
• To avoid personal injury, please pay extra attention to the children around when using the washer.
• Familiarize yourself with the control parts of the washer, and depressurize or stop the washer as soon as possible if needed.
• Always keep yourself alert when using the washer in a cleaning task.
• Do not operate the washer when you are fatigued, or after drinking alcohol or using medications that may compromise your consciousness.
• Make sure that there is no unnecessary personnel in the area where you are using the washer.
• Do not place the washer on an unstable stand. Keep the washer stable and balanced at all times.
• Strictly abide by the maintenance instructions specified in the user manual, and do not disassemble the washer on your own.

Safety Warnings for Battery Pack

• Do not open or shred the battery pack.
• Do not expose the battery pack to heat or flames. Keep the battery pack away from direct sunlight.
• Do not short-circuit the battery pack. Do not store the battery pack in a box or drawer without precaution. Store the battery pack separately to avoid short circuits with other battery packs or  metal objects.
• Protect the battery pack from mechanical shock.
• In case of accidental battery leakage, do not directly contact the leaked liquid with your skin or eyes. In case of contact, flush with plenty of water.
• Correctly align the positive and negative poles of the battery pack to ensure proper use. Do not use battery packs that are not intended for the washer.
• Keep the battery pack away from children.
• Keep the battery pack clean and dry.
• Please use a dry and clean cloth to wipe the battery pack interface.
• Charge the battery pack before use.
• After long-term storage, the battery pack needs to be charged and discharged several times for optimal performance.
• The battery pack is at its best performance when used at room temperature of 20°C ± 5°C. Please keep the washer’s original user manual for future reference.
• The battery pack is for its intended use only.
• Disconnect the washer from power before removing the battery pack.

Note
The washer will be tested to use before leaving the factory to ensure quality. There may be a few water stains inside when unpacking for the first time, which is normal. Please feel free to use it.

Specifications

• Model: QWXCJ002

• Item Dimensions: 545×244×84 mm

• Net Weight: 1.5 kg

• Rated Input: 5V 10W/9V 18W/12V 24W/ 15V 30W/20V 40W

• Motor Power: 330 W

• Battery Type: Lithium-ion battery pack

• Rated Capacity: 2500 mAh(18 V )

• Nominal Energy: 45 Wh

• Rated Pressure and Flow Rate:

• Self-priming Way: Jet mode/Tilted mode/20-degree/40-degree Water Mode:

• Pressure 18 ± 2 Bar, flow rate 160 ± 20 L/H Foam/Shower Mode:

• Pressure 3±3 Bar, flow rate 210±20 L/H

• Water-Supplying Way:
  The outlet water pressure and flow rate will vary along with the inlet water pressure.

• Max. Inlet Water Pressure: 0.7 MPa

Notes:

• Self-priming way: The washer automatically absorbs water through a hose.
• Water-supplying way: The washer uses water via a faucet, but the relevant accessories should be purchased separately.

Care & Maintenance

Please disassemble the relevant components from the washer before performing the maintenance.
Please check whether the washer and components are damaged before each use. If any, stop using the washer and contact the supplier or manufacturer to replace the damaged compo-nents.

Cleaning the Water Inlet Filter

• Rotate the water inlet filter head to remove the lower part, then take out the filter for cleaning.
• After cleaning, put the filter back into the filter head and rotate the filter head to reassemble it.

Cleaning & Storage

• Drain the machine and the water pipe before storage. Wipe the machine body with a soft brush or a clean cloth. Do not use water, solvents or polishes. Keep the machine in a safe and dry place away from children. Do not place articles on the machine.
• Please protect the washer and accessories from frost in storage.

Troubleshooting

The washer starts, but the self-priming function does not work, or the pressure is inadequate.| The washer is too much higher than the water surface level.

The hose female connector

| Lower the washer till it is 1.5 m below the water surface level.
The hose female connector and the hose male connector are poorly connected.| Connect the hose female connector to the hose male connector properly.
The water inlet filter is blocked or not full submerged in water.| Clean the water inlet filter/filter head and fully submerge them in water.
The hose is bent or twisted.| Straighten the hose.
The multi-function nozzle leaks water.| The nozzle is not fully rotated into place.| Rotate the nozzle fully into place.
Water flows out after the washer is turned off.| There is water residue in the pump after the washer is turned off.| Drain the water residue before storage.
No soap sprays out at the foam/shower mode.| There is no soap in the soap holder.| Refill the soap.
The washer does not start.| The battery pack is not properly installed.| Reinstall the battery pack.
The battery pack is depleted.| Charge the battery pack before use.
The pressure of the washer is discontinuous.| Air is drawn by the pump.| Make sure the hose and the washer are properly connected.
Fully submerge the water inlet filter head in water.
The washer automatically stops.| The battery pack is depleted.| Charge the battery pack before use.
The battery pack is too hot, and the overheat protection is enabled.| Wtuarnitinfogrothnethteemwpaesrhaetru.re to drop before
The self-priming function does not work when the washer has not been used for a long time.| Air is trapped in the pump.| Put the water inlet filter head into a bucket or connect the washer to a faucet, then turn on the washer. Regulatory Compliance Information

Europe — EU declaration of conformity

We, Shanghai HOTO Technology Co., Ltd., hereby, declare that this equipment is in compliance with the applicable Directives and European Norms, and amendments.

Disposal and recycling information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health. Please contact the installer or local authorities for more information about the location as well as terms and conditions of such collection points.

Manufacturer: Shanghai HOTO Technology Co., Ltd.
Address: Building 45, No. 50 Moganshan Rd, Putuo District, Shanghai, PRC, 200060.

DECLARATION OF CONFORMITY

EU Declaration of Conformity
We
Shanghai HOTO Technology Co., Ltd.

Declare that the product:
HOTO 20V Pressure Washer Pro / QWXCJ002

Complies with the essential health and safety requirements of the following directives:
2006/42/EC The Machinery Directive

References to the following harmonized standard were made:
EN 62841-1:2015
EN 62841-2-1:2018+A11:2019
2014/30/EU Electromagnetic Compatibility directive References to the following harmonized standard were made:
EN55014-1: 2017 EN55014-2: 2015 EN 61000-3-2:2014 EN 61000-3-3:2013

2011/65/EU+ (EU) 2015/863 Restrictions of the Use of Certain Hazardous Substances in Electrical and Electronic Equipment
Authorised signatory and technical file holder:
Shanghai HOTO Technology Co., Ltd.
Building 45, No.50 Moganshan Road, Shanghai, China

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>