HOTO QWXCJ001 20V Cordless High Pressure Washer User Manual

October 30, 2023
HOTO

HOTO QWXCJ001 20V Cordless High-Pressure Washer

HOTO-QWXCJ001-20V-Cordless-High-Pressure-Washer-
PRODUCT

Product Overview

The HOTO 20V Cordless High-Pressure Washer is a compact and portable device designed for various cleaning applications. It comes with a multifunctional jet nozzle, foam tank, transparent water inlet hose, self-priming water filter, 20V charger, battery pack release button, inlet hose connector, and safety lock.

Operating Procedures

  1. Wear goggles, earmuffs, a protective suit, and non-slip shoes when operating.
  2. Insert the 20V battery pack into the battery holder on the device.
  3. Connect the quick connector of the inlet hose to the inlet hose connector. Put the self-priming filter into the water after connection. Make sure the filter is fully immersed in the water.
  4. Connect the multifunctional jet nozzle to the device. Unlock the Safety Lock, and pull the trigger to turn on the device.
  5. Connect the foam tank to the quick connector of the device. Pull the trigger to spray the foam.

After Use

  1. Disconnect the multifunctional jet nozzle.
  2. Pull down the quick connector of the hose. Take the self-priming filter out of the water.
  3. Press the battery pack release button and take out the battery pack.
  4. Unplug the waterproof plug on the battery pack charging hole and insert the charger for charging. When the red charging light is on, it indicates normal charging. When the red light turns green, it indicates the completion of charging. Please use the original charger!

Maintenance for Longer Service Life

  1. Take off the filter net at the inlet hose connector. Screw off the self-priming filter and take out the filter net.
  2. Rinse the filter nets with clean water in time (It is recommended that the filter nets be cleaned once every 3 to 5 times of use according to the local water supply).
  3. Please pay attention to the battery level and charge in time
    when the battery level is low. Frequent loss of power may lead to the sleep state of the battery pack.

Technical Specifications

  • Name: HOTO 20V Cordless High-Pressure Washer
  • Model: QWXCJ001
  • Battery Type: Lithium-ion battery pack
  • Rated Voltage: 20V
  • Capacity: 200W
  • Water Pressure: 24bar

Application Scenarios

This device is applicable to car washing, deep cleaning such as window washing, and plants watering or light cleaning.

Product Safety

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference.

WARNING: This product can expose you to chemicals including lead, phthalate or bisphenol A which are known to the State of California to cause cancer, birth defects or other reproductive harm. Wash your hands after use. For more information go to www.P65Warnings.ca.gov.

IMPORTANT SAFETY INSTRUCTIONS

WARNING: When using this product basic precautions should always be followed, including the following:

  1. Read all the instructions before using the product.
  2. To reduce the risk of injury, close

SAFETY WARNINGS FOR BATTERY PACK

  1. Do not dismantle, open or shred the battery pack.
  2. Do not expose the battery pack to heat or fire. Avoid storage in direct sunlight.

Product Overview

Please read this manual carefully before use, and retain it for future reference.HOTO-QWXCJ001-20V-Cordless-High-Pressure-Washer-
FIG-1

  1. Multifunctional Jet Nozzle
  2. Foam Tank
  3. Transparent Water Inlet Hose
  4. Self-priming Water Filter
  5. 20V Charger
  6. Battery Pack Release Button
  7. Battery Pack Charging Hole
  8. Inlet Hose Connector
  9. Safety Lock

Operating Procedures

HOTO-QWXCJ001-20V-Cordless-High-Pressure-Washer-
FIG-4

  1. Please wear goggles, earmuffs, a protective suit, and non-slip shoes when operating.
  2. Insert the 20V bakery pack into the battery holder on the device
  3. Connect the quick connector of the inlet hose to the inlet hose connector. Put the self-priming filter into the water aner connection. Make sure the filter is fully immersed in the water
  4. Connect the multifunctional jet nozzle to the device. Unlock the Safety Lock, pull the trigger to turn on the device.
  5. Connect the foam tank to the quick connector of the device. Pull the trigger to spray the foam.

After Use

HOTO-QWXCJ001-20V-Cordless-High-Pressure-Washer-
FIG-5

  1. Disconnect the multifunctional jet nozzle.
  2. Pull down the quick connector of the hose.
    • Take the self-priming filter out of the water.
  3. Press the battery pack release button and take out the battery pack.
  4. Unplug the waterproof plug on the battery pack charging hole and insert the charger for charging.
    • When the red charging light is on, it indicates normal charging.
    • When the red light turns green, it indicates the completion of charging.
    • Please use the original charger!

Maintenance

Longer service life for the deviceHOTO-QWXCJ001-20V-Cordless-High-
Pressure-Washer-FIG-7

  1. Take off the filter net at the inlet hose connector. Screw off the self-priming filter and take out the filter net.
  2. Rinse the filter nets with clean water in time (It is recommended that the filter nets be cleaned once every 3 to 5 times of use according to the local water supply).
  3. Please pay attention to the battery level and charge in time when the battery level is low. Frequent loss of power may lead to the sleep state of the battery pack.

Technical Specifications

  • Name: HOTO 20V Cordless High-Pressure Washer
  • Model: QWXCJ001
  • Battery Type: Lithium-ion battery pack
  • Rated Voltage: 20V
  • Capacity: 200W
  • Water Pressure: 24bar
  • Flow Rate: 180 L/h
  • Feed temperature: 0-40°C
  • Charging   time: 3-5h
  • Operating time: Around 20min
  • Weight: 2.25kg

Application Scenarios

HOTO-QWXCJ001-20V-Cordless-High-Pressure-Washer-
FIG-8

Product Safety

WARNING: Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury. Save all warnings and instructions for future reference.
WARNING: This product can expose you to chemicals including lead, phthalate or bisphenol A which are known to the State of California to cause cancer, birth defects or other reproductive harm. Wash your hands after use. For more information go to www.P65Warnings.ca.gov.

SAFETY INSTRUCTIONS

IMPORTANT

WARNING: When using this product basic precautions should always be followed, including the following:

  1. Read all the instructions before using the product.
  2. To reduce the risk of injury, close supervision is necessary when a product is used near children.
  3. Know how to stop the product and bleed pressures quickly. Be thoroughly familiar with the controls.
  4. Stay alert – watch what you are doing.
  5. Do not operate the product when fatigued or under the influence of alcohol or drugs.
  6. Keep the operating area clear of all persons
  7. Do not overreach or stand on unstable support. Keep good footing and balance at all times.
  8. Follow the maintenance instructions specified in the manual.
  9. WARNING – Risk of injection or injury- do not direct discharge stream at persons.
  10. Do not spray electrical apparatus and wiring.

SAVE THESE INSTRUCTIONS

SAFETY WARNINGS FOR BATTERY PACK
  • Do not dismantle, open or shred battery pack.
  • b) Do not expose the battery pack to heat or fire. Avoid storage in direct sunlight.
  • c) Do not short-circuit a battery pack. Do not store battery packs haphazardly in a box or drawer where they may short-circuit each other or be short-circuited by other metal objects. When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws, or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or fire.
  • d) Do not remove the battery pack from its original packaging until required for use.
  • e) Do not subject the battery pack to mechanical shock.
  • f) In the event of battery leaking, do not allow the liquid to come in contact with the skin or eyes. If contact has been made, wash the affected area with copious amounts of water and seek medical advice.
  • g) Observe the plus (+) and minus (-) marks on the battery back and equipment and ensure correct use.
  • h) Do not use any battery pack which is not designed for use with the equipment.
  • Keep the battery pack out of the reach of children.
  • Seek medical advice immediately if a cell or battery has been swallowed.
  • k) Always purchase the battery pack recommended by the device manufacturer for the equipment.
  • i) Keep the battery pack clean and dry.
  • m) Wipe the battery pack terminals with a clean dry cloth if they become dirty.
  • n) Battery pack need to be charged before use. Always use the correct charger and refer to the manufacturer’s instructions or equipment manual for proper charging instructions.
  • o) Do not leave battery pack on prolonged charge when not in use.
  • p) After extended periods of storage, it may be necessary to charge and discharge the battery pack several times to obtain maximum performance.
  • q) Battery pack gives its best performance when it is operated at normal room temperature (20 °C + 5 °C).
  • r) When disposing of battery packs, keep battery packs of different electrochemical systems separate from each other.
  • s) Recharge only with the charger specified by WORX Do not use any charger other than that specifically provided for use with the equipment. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
  • t) Retain the original product literature for future reference.
  • u) Use only the battery pack in the application for which it was intended.
  • v) Remove the battery pack from the equipment when not in use.
  • w) Dispose of properly.

Connect to pressurized water supply

  • The maximum feed pressure and tempera- ture of the inlet are 0.7MPa/7bar and 40°C respectively.
  • Check whether the filter is installed inside the inlet hose and is not blocked.
  • Connect the hose to the water tap using the quick connector and then open the water tap.
  • Before connecting the hose to the device, let the water flow through the hose to prevent sand and dirt from entering the device.
  • Turn off the water tap and connect the hose to the inlet using the quick connector.

troubleshooting

Issue Possible Causes Solution
The lithium ba very pack indicator flashes Insufficient ba very power.

Charge the ba very in time.
No power an er turning on| Insufficient ba very power. The ba very pack is not properly installed.| Charge the ba very in time.

Reinsert the battery pack into the battery holder and make sure it is properly connected.

Unexpected halt| Automatic overheating protection.| Turn it on after it cools down.
The ba ery pack cannot be charged| The ba very is not properly connected to the charger.

The charger is not connected to the power supply.

Unmatched charger.

| Reinsert the charger into the charging hole and make sure it is properly connected.

Check whether the power supply is energized and make sure the charger is properly connected- ed to it (the power indicator flashes or not).

Charge using the original adapter.

Small water output| The filter is clogged causing poor water inflow.

The inlet hose is folded. Impure water supply. The nozzle is clogged.

| Clean the filter net on the water filter and the inlet filter net.

Straighten out or replace the water inlet hose. Use clean water.

Clean the jets inside the nozzle.

Fail to pump water

| The hose connector is not properly connected to the inlet.

The self-priming water filter is not fully immersed in the water.

The inlet seal ring falls off or is damaged.

| Connect the inlet hose connector to the inlet properly.

Fully immerse the water filter in the water.

Install or replace the seal ring.

Long waiting time for water output| Small water output.| Refer to the solution for small water output.
Leaking water outlet| The nozzle is not properly installed.| Properly install the nozzle on the device.

Manufacturer: Shanghai HOTO Technology Co., Ltd.
Address: Building 45, No. 50 Moganshan Rd, Putuo District, Shanghai, PRC, 200060.

Documents / Resources

| HOTO QWXCJ001 20V Cordless High Pressure Washer [pdf] User Manual
QWXCJ001, QWXCJ001 20V Cordless High Pressure Washer, 20V Cordless High Pressure Washer, Cordless High Pressure Washer, High Pressure Washer, Washer
---|---
| HOTO QWXCJ001 20V Cordless High Pressure Washer [pdf] User Manual
QWXCJ001, QWXCJ001 20V Cordless High Pressure Washer, 20V Cordless High Pressure Washer, Cordless High Pressure Washer, High Pressure Washer, Washer

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals