AIXPI JY1911-70 Solar Induction Light Instruction Manual

AIXPI JY1911-70 Solar Induction Light

Product Information

The Solar Induction Light is a wall light that is designed to illuminate when there is human movement detected and the ambient light level is below 20 Lux. It operates using solar energy, storing electricity during the daytime to power the light at night.  The light source of this luminaire is not replaceable, so the entire luminaire will need to be replaced when the light source reaches its end of life. The sensitivity of the PlR sensor is affected by temperature, with higher temperatures resulting in a shorter detection range. The product comes with a 12-month warranty.

Product Usage Instructions

1. Before first use, turn on the switch by pushing it to the left.
2. Cover the solar panel before testing the light.
3. Place the lamp under direct sunlight for 6-8 hours to charge it.
4. If the lamp doesn’t work after charging, follow these steps:
   • Ensure the switch is turned on.
   • Install the lamp in a location exposed to direct sunlight.
   • Charge the lamp for 6-8 hours before first use.
5. The lamp will turn on when people approach it and automatically turn off after approximately 20 seconds when people leave.
6. The lamp can be adjusted to different angles:
   • The lamp can be rotated up and down by 135 degrees.
   • The two lights attached to the left and right can be rotated forward and backward by 135 degrees and up and down by 90 degrees.
   • Caution: Do not rotate any part at too large an angle to avoid disconnection of the internal circuit.
7. Installation Instructions:
   • Remove the bottom of the solar sensor light.
   • Fix the removed bracket on the wall and mark the positions of the three holes with a pen.
   • Punch holes in the marked positions.
   • Use a hammer to drive the wall plug into the punched hole.
   • Align the bracket to the hole and use a Phillips screwdriver to fix the screw on the bracket.
   • The bracket is now installed.
   • Finally, install the lamp on the fixed bracket.
   • Assembly is now completed.

If you need any further assistance, please feel free to contact us at service01@aixpi.com.
Thank you for choosing our product!

Notes & Precautions

1. After the switch is turned to the “ON” position, the wall light only illuminates when the ambient light level is below 20 Lux and there is human movement detected.
2. The number of uses depends on the amount of electricity stored during the daytime, which is affected by the intensity and duration of sunlight.
3. Temperature affects the sensitivity of the PlR sensor, causing the detection range to vary.The higher the temperature is, the shorter the detection range will be.
4. If the light fails to light up after* days of continuous rainy or cloudy weather, it is because the battery has been exhausted. The light will function normally again at night after a sunny day.
5. Please turn the switch off; If the lamp doesn’t work, please install the lamp in a location exposed to direct sunlight, and charge it for 6-8h before 1st time use.
6. The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced

Specification

• 6W, 70 LEDs, Lithium-ion battery 3.7V DC, 1500 mAh 18650 1.62A, 6500K, IP65, ABS\PC\PE,-25°C-40°C/-13°F-104°F

Tast

1. Turn on the switch first;
2. Cover the solar panel before the test;
3. Put the lamp under the sun for 6-8 hours, if it doesn’t work.

Light mode

• Please push to the left to start the switch for first use, it will be on when people approach the light, and it will be off after about 20 seconds when people leaves the light.

Various angles can be adjusted

1. The lamp can be rotated to left or to right by 75 degrees,(Please do not directly turn to one side over 75 degrees). The lamp can be rotated up and down by 135 degrees.
2. The two lights attached to the left and right can be rotated forward and backward by 135 degrees, and up and down by 90 degrees.
3. Caution : All rotating parts should not be rotated at too large an angle, which might cause disconnection of the internal circuit.

Product List

Installation Instructions

1. Remove the bottom of the solar sensor light.
2. Fix the removed bracket on the wall and mark the positions of the three holes with a pen.
3. Punch holes in the marked positions.
4. Use a hammer to drive the wall plug into the punched hole.
5. Align the bracket to the hole, and use a Phillips screwdriver to fix the screw on the bracket.
6. The bracket is installed
7. Finally, install the lamp on the fixed bracket.
8. Assembly Completed.

Dear Customer:
Thank you for purchasing our products. If you need any help, please feel free to contact us, our email address: service01@aixpi.com
We provide 12 month warranty. Thanks and best regards.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>