HOLLYLAND Cosmo C1 Wireless HDMI SDI Video Transmission System User Guide
- June 14, 2024
- HOLLYLAND
Table of Contents
HOLLYLAND Cosmo C1 Wireless HDMI SDI Video Transmission System
FOREWORD
Thank you for purchasing the Cosmo C1 wireless video transmission system. Please read the instruction carefully before using the product. Wish you a pleasant experience.
KEY FEATURES
- As Low As 40ms Transmission Latency
- 350m Wireless Transmission Range (LOS)
- Supports Smart Channel Selection
- Transmitter Supports SDI Input, HDMI Input, and SDI Loopout
- Receiver Supports 2*SDI Outputs and HDMI output
- Supports DC Power Supply, Battery, and USB Type-C Power Supply
- Supports UVC Pull-streaming (Based on P format)
PACKING LIST
- Transmitter x1
- Receiver x1
- Antenna x4
- Mushroom Antenna x2
- Cold Shoe x1
- Peasecod Pan-tilt with Cold Shoe x1
- Type-C Converter x1
- DC Adapter x1
- User Guide x1
- Warranty Card x1
- Expansion Accessory x1
TYPICAL SETUP
Note : The transmitter can be equipped with mushroom antenna. When there is a large height difference between the transmitter and receiver, it is recommended to use Hollyland mushroom antenna at the transmitter to improve the stability of wireless transmission.
PRODUCT INTERFACES
A: TRANSMITTER
- Antenna Interface
- HDMI Input
- SDI Input
- SDI Loop out
- DC Power Input
- Expansion Accessories Mounting Hole
- LED Light (Yellow light indicates connection status, red light indicates low power)
- OLED Screen
- Thumbwheel Switch
- Power Switch
- USB Type-C Interface
- Outlet
- 1/4 Threaded hole
B: RECEIVER
- Antenna Interface
- HDMI Output
- SDI Output 1
- SDI Output 2
- DC Power Input
- Expansion Accessories Mounting Hole
- LED Light (Yellow light indicates connection status, red light indicates low power)
- OLED Screen
- Thumbwheel Switch
- Power Switch
- USB Type-C Interface
- Outlet
- 1/4 Threaded Hole
INSTALLATION
INSTALLATION OF TRANSMITTER
- Install the antenna according to the angle shown in the picture.
- Install the magic arm onto the 1/4 threaded hole of the transmitter and install the assembled transmitter into the camera body.
- Install the battery (compatible with NP-F970 and others of same series).
- Push the power switch to turn on the device.
INSTALLATION OF RECEIVER
- Install the antenna according to the angle shown in the picture.
- Install the receiver onto the stent through the 1/4 threaded hole on the bottom of the device.
- Install the battery (compatible with NP-F970 and others of same series).
- Push the power switch to turn on the device.
OLED DISPLAY
- Signal Strength
- Indicator of Power Supply
- Video Format
- Channel Display
- Indicator of Auto-frequency-hopping
NOTE: The “AUTO” indicates that the frequency point is in the automatic frequency hopping mode (the picture on the right); switch the frequency manually will change the device to the locked-frequency-mode state in the left picture.
QUICK GUIDE
ENTER MENU
Long press the thumbwheel switch for three seconds to enter the menu. Flip the
toggle wheel up or down to switch menu options, and click to confirm.
CHANNEL SWITCHIN
Toggle up/down the switcher to change the menu options on the transmitter or
receiver, click the confirm key to confirm the channel, then the receiver and
the transmitter channel will be synchronized automatically.
PRODUCT PARAMETERS
| Transmitter | Receiver |
|---|
Interfaces
| Antenna Interface (RP-SMA Male) HDMI Input (Type A Female)
SDI Input SDI Loopout DC Input USB Type-C
| Antenna Interface (RP-SMA Male) HDMI Input (Type A Female)
SDI Output *2 DC Input
USB Type-C
Power Supply
| DC Power Input: 6~16V
USB Type-C Power Supply: 5V/2A Battery Power Supply: 6-16V
| DC Power Input: 6~16V
USB Type-C Power Supply: 5V/2A Battery Power Supply: 6-16V
Power Consumption| <9W| <9W
Weight| 214g (Without Exterior Antenna)| 214g (Without Exterior Antenna)
Dimension
| (LWH): 1157032mm (The Battery Plate Exclude)| (LWH): 1157032mm (The Battery Plate Exclude)
Input/Output Video Format
| HDMI: 480p60576p50720p50/59.94/60
1080i50/59.94/60
1080p23.98/24/25/29.9/30
1080p50/59.94/60
SDI:
1080p60/59.94/50 (Level A)
1080p60/59.94/50 (Level B)
1080i60/59.94/50
1080p30/29.97/25/24
/23.981080psf25 720p60/59.94/50
1080psf24/23.98
| HDMI:
480p60
576p50
725p50/60
1080i50/60
1080p24/25/30
1080p50/60
SDI:
1080p60/50 (Level A)
1080i60/50
1080p30/25/24
1080psf25/24
720p60/50
Frequency| 5.1GHz~5.8GHz| 5.1 GHz~5.80 GHz
Transmission Power| Maximum 22dBm| /
Receiver Sensitivity| /| -80dBm
Transmission Latency| As low as 40 ms
Bandwidth| 20MHz| 20MHz
SUPPORT
If encounter any problems in using the product or need any help, please follow these ways to get more technical support:
Hollyland User Group
HollylandTech
HollylandTech
HollylandTech
support@hollyland-tech.com
www.hollyland-tech.com
FCC REQUIREMENT
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help. This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Shenzhen Hollyland Technology Co., Ltd.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>